Which oil filter fits your 2014 Ram 1500

The 2014 Dodge Ram 1500 uses a Mopar 68157291AA oil filter as the factory part, or equivalent aftermarket filters that meet the same specifications. The filter is a spin-on cartridge located on the driver's side of the engine block, below the intake manifold. You can also use Fram PH8A, Motorcraft FL-400S, or Wix 51515 as direct replacements — all three are widely available and cost between $8 and $15.

The filter capacity is 1.5 quarts, and the thread size is 3/4-16 UNF (the standard size for most Ram trucks). If you're buying online or at a parts counter, confirm the part number matches your specific engine — the 3.6L V6, 5.7L V8, and 8.0L V10 all use the same filter location and size, but it's worth double-checking before you leave the store.

Key Takeaways

  • The factory Mopar filter is 68157291AA; Fram PH8A, Motorcraft FL-400S, and Wix 51515 are direct aftermarket replacements that fit the same location.
  • The filter threads are 3/4-16 UNF, the standard size for Ram 1500 trucks, so most spin-on filters at auto parts stores will work.
  • The filter sits on the driver's side of the engine block below the intake manifold and holds 1.5 quarts of oil.
  • Replacement takes about 10 minutes once you locate the filter; drain the old oil first, then unscrew the filter by hand and install the new one hand-tight.

How to locate and access the filter on your Ram

Open the hood and look toward the driver's side of the engine block, just below where the intake manifold sits. The filter is a cylindrical cartridge about 4 inches tall and 3 inches wide. You may need to remove the plastic engine cover or air intake ducting to reach it comfortably — both are held on by clips or bolts and take less than a minute to remove.

If you're working under the truck, the filter is easier to access from below. Raise the truck on jack stands (never rely on a jack alone), and you'll see the filter hanging down from the engine block. This angle also makes it simpler to catch dripping oil in a drain pan. Have a rag or old towel ready — some oil will spill when you unscrew the filter, even if you've drained the pan.

Step-by-step filter replacement

Start by draining the engine oil into a pan. Locate the drain plug on the bottom of the oil pan (passenger side, toward the rear), unscrew it by hand or with a wrench, and let the oil drain completely — this takes 5 to 10 minutes. Once the flow slows to a drip, wipe the drain plug clean, check the rubber washer for damage, and screw it back in hand-tight, then snug it with a wrench (do not over-tighten).

Next, position your drain pan under the oil filter. Use an oil filter wrench to unscrew the old filter — grip it near the base and turn counterclockwise. Once it's loose enough, finish unscrewing by hand. Tip the filter upright as you remove it to avoid spilling oil down your arm. Wipe the filter mounting surface on the engine block with a clean rag to remove any old rubber gasket material or debris.

Before installing the new filter, coat the rubber gasket (the ring around the top of the filter) lightly with fresh oil — this helps create a watertight seal and makes removal easier next time. Screw the new filter on by hand until the gasket contacts the mounting surface, then turn it an additional three-quarter turn. Do not use a wrench to tighten it; hand-tight is correct. Over-tightening will damage the gasket and make the filter stick next time.

Oil capacity and viscosity for your 2014 Ram 1500

The 2014 Ram 1500 holds 5 quarts of oil if you're replacing only the filter, or 6 quarts if you're doing a full drain and refill (the extra quart accounts for oil left in the engine passages and filter). Check your owner's manual for the exact capacity of your engine — the 3.6L V6 and 5.7L V8 have slightly different volumes.

Dodge recommends SAE 5W-20 oil for all 2014 Ram 1500 engines. This viscosity is printed on the oil cap under the hood. Use the same weight every time; switching between 5W-20 and 10W-30, for example, can affect fuel economy and engine wear. Synthetic, semi-synthetic, and conventional oils all meet the 5W-20 spec — the choice depends on your budget and how long you want to run between changes.

When to replace the filter during regular maintenance

Dodge's factory maintenance schedule calls for an oil and filter change every 10,000 miles under normal driving conditions, or every 3 months if you drive fewer miles in that period. If you tow frequently, drive in stop-and-go traffic, or operate the truck in dusty conditions, change the filter every 5,000 miles instead. The filter itself degrades over time even if you're not driving, so a seasonal change (spring and fall) is reasonable if you use the truck only occasionally.

Check your oil level monthly using the dipstick under the hood. A low reading doesn't always mean you need an oil change, but it's a sign the engine is burning oil or leaking — either way, have it inspected. If the oil on the dipstick looks black or gritty, change it sooner than the scheduled interval, regardless of mileage.

Disposal and recycling of used oil and filters

Used motor oil is recyclable and should never go down a drain or into the trash. Most auto parts stores that sell oil (Autozone, O'Reilly, Advance Auto Parts, Napa) will take used oil and filters for free, even if you didn't buy the replacement oil from them. Bring the oil in a sealed container — a milk jug, old oil bottle, or drain pan with a lid all work. Some stores limit the amount to 5 gallons per visit, so call ahead if you're disposing of more.

Used oil filters can also be recycled. Many recycling centers accept them, and some auto parts stores will take them alongside the oil. If the filter is still dripping, place it in a cardboard box or on newspaper to prevent staining your vehicle or the store's floor. Never leave an oil filter in the trash — the oil inside contaminates soil and groundwater.

Frequently Asked Questions

Can I use a different oil filter size or brand?

Yes, as long as it's a 3/4-16 UNF spin-on filter rated for your engine size. Fram, Wix, Motorcraft, and Bosch all make filters that fit the 2014 Ram 1500. Avoid filters significantly cheaper than the Mopar part — they may have thinner media or weaker gaskets. Mid-range filters ($10–$15) are usually reliable.

How tight should I screw the new filter on?

Hand-tight plus three-quarter turn. Tighten until the rubber gasket contacts the engine block, then rotate the filter body an additional 270 degrees. This compresses the gasket enough to seal without crushing it. Over-tightening makes the filter stick and can tear the gasket when you remove it next time.

What if oil leaks from the filter after I install it?

Check that the old rubber gasket isn't stuck to the engine block — if two gaskets are present, the new filter won't seal. Wipe the mounting surface clean and reinstall the filter. If it still leaks, the new filter may be defective; return it and try a different brand or part number.

Do I need to change the filter every time I change the oil?

Yes. The filter traps contaminants and degrades as oil circulates through it. A clogged filter restricts oil flow and can trigger the low-oil-pressure warning light. Changing the filter with every oil change ensures clean filtration and protects engine bearings.

Can I reuse the old filter if I'm just topping off oil?

No. Topping off oil is not the same as an oil change. If you're only adding a quart because the level is low, the filter stays in place. But if you're doing a full drain and refill, always install a new filter — reusing an old one defeats the purpose of changing the oil.