The 2013 Altima uses a cartridge-style oil filter located on top of the engine
The 2013 Nissan Altima's oil filter is not a spin-on canister like many older cars. Instead, it's a cartridge filter housed in a plastic cap on the top of the engine, near the front. This design is common on modern Nissans and requires a different removal process than traditional filters — you unscrew the cap, pull out the cartridge, and replace it rather than unscrewing an entire filter unit.
The filter sits directly above the engine block and is straightforward to access without lifting the car or removing other parts. You'll need a filter wrench to remove the cap, but the job itself takes about 10 to 15 minutes once you have the right tools and a new filter on hand.
Key Takeaways
- The 2013 Altima has a cartridge-style oil filter in a cap on top of the engine, not a traditional spin-on filter.
- You will need a cartridge oil filter wrench (also called a cap wrench) to remove and reinstall the filter cap.
- The correct replacement filter is Nissan part number 15208-9E000 or an equivalent OEM or aftermarket cartridge filter rated for your engine size.
- Always replace the rubber O-ring seal on the filter cap when you change the filter to prevent oil leaks.
- The job takes about 10 to 15 minutes and requires only basic tools, a drain pan, and the correct filter wrench.
What filter size and part number your 2013 Altima needs
The 2013 Nissan Altima comes in two engine sizes — a 2.5-liter four-cylinder and a 3.5-liter V6 — and both use the same cartridge filter housing. The OEM Nissan part number is 15208-9E000, which fits both engines. This is the filter Nissan dealers stock and install, and it's the safest choice if you want to match the factory specification exactly.
Aftermarket brands like Fram, Mobil 1, Purolator, and Bosch all make cartridge filters that fit the 2013 Altima. When shopping, look for filters labeled as fitting a 2013 Nissan Altima or a Nissan Altima with a cartridge-style filter housing. The filter itself is small and cylindrical, about 3 inches tall and 2 inches in diameter. Avoid buying a spin-on filter by mistake — they will not fit this car.
The filter cap also has a rubber O-ring seal that sits between the cap and the engine block. Many shops and owners replace this O-ring every time they change the filter to prevent leaks. Nissan sells the O-ring separately (part number 11065-1XF0A), or it often comes pre-installed on replacement filter caps sold as kits.
Tools and supplies you'll need
To change the oil filter on a 2013 Altima, gather these items before you start: a cartridge oil filter wrench (the most important tool), a new oil filter, a small drain pan or container, clean rags or paper towels, and optionally a new O-ring seal for the filter cap. The filter wrench is a socket-like tool that grips the filter cap and allows you to turn it without stripping the plastic threads. You can buy one at any auto parts store for $10 to $20, and it works on all Nissan cartridge filters.
You do not need to lift the car or remove the wheel well to access this filter. The cap sits on top of the engine and is reachable from above. A flashlight helps if you're working in dim light, and having a small funnel nearby makes it easier to pour new oil back in after the filter change, though it's not required for the filter swap itself.
Step-by-step filter removal and installation
Start with a cold or warm engine — not hot — to avoid burns. Open the hood and locate the filter cap on top of the engine, toward the front. It's a round plastic cap about 3 inches in diameter with a center bolt on top. Place your drain pan underneath it to catch any oil that spills when you open it.
Using the cartridge filter wrench, grip the cap and turn it counterclockwise to unscrew it. It will come free in your hand. Inside the cap, you'll see the old cylindrical filter cartridge. Pull it straight out and set it aside. A small amount of oil will drip from the cap and the engine block, so keep the drain pan in place.
Before installing the new filter, inspect the rubber O-ring seal on the underside of the cap. If it looks cracked, hardened, or damaged, replace it now. If you're keeping the old cap, clean the O-ring and the sealing surface on the engine block with a clean rag to remove any dirt or debris. Slide the new filter cartridge into the cap, making sure it sits flat and fully inserted. The filter should not be forced — it slides in smoothly.
Thread the cap back onto the engine block by hand first to avoid cross-threading the plastic. Once it's hand-tight, use the filter wrench to snug it down. Do not over-tighten — the cap only needs to be tight enough that the O-ring seals properly. A quarter-turn past hand-tight is usually sufficient. Start the engine and check for leaks around the cap. If oil drips, turn off the engine, let it cool slightly, and tighten the cap a bit more.
Common mistakes to avoid
The most common error is forgetting to replace or inspect the O-ring seal. A worn or missing O-ring will cause the filter cap to leak oil even if it's tight. Always look at the O-ring when you open the cap, and replace it if there's any doubt about its condition. A new O-ring costs just a few dollars and takes seconds to install.
Another mistake is over-tightening the cap. The plastic threads on the cap can strip if you use too much force with the wrench. Hand-tight plus a quarter-turn is the right amount. If the cap is leaking after you've tightened it, the problem is usually a bad O-ring, not a loose cap.
Do not buy a spin-on filter thinking it will fit. The 2013 Altima's engine is designed for a cartridge filter only. A spin-on filter will not thread onto anything on this car, and you'll waste time and money trying to make it work.
When to change the oil filter
Nissan recommends changing the oil filter every time you change the engine oil. For a 2013 Altima, that's typically every 3,000 to 5,000 miles with conventional oil, or every 7,500 to 10,000 miles with synthetic oil, depending on your driving conditions and the oil type you use. Check your owner's manual or the maintenance schedule sticker under the hood for the exact interval for your car.
If you're doing an oil change yourself, the filter swap takes only a few extra minutes and is worth doing at the same time. If you're having the oil changed at a shop, confirm that the filter is being replaced as part of the service — some budget shops may skip it or charge extra.
Frequently Asked Questions
Can I change the oil filter without changing the oil?
Yes, you can change just the filter if you want, but it's not recommended. The filter and oil work together to keep the engine clean, and replacing one without the other defeats the purpose. Most people change both at the same time for simplicity and cost-effectiveness.
What happens if I over-tighten the filter cap?
Over-tightening can crack the plastic cap or strip the threads on the engine block, making it impossible to seal properly. If this happens, you'll need a replacement cap, which costs $30 to $50 from a Nissan dealer. Hand-tight plus a quarter-turn is all you need.
Is the O-ring included with the replacement filter?
Some aftermarket filters come with a new O-ring, but not all. Check the package before you buy. If the O-ring isn't included and you need one, Nissan part number 11065-1XF0A is the correct replacement, or you can reuse the old one if it's in good condition.
Do I need to prime the new filter with oil before installing it?
No. Cartridge filters for the 2013 Altima do not need to be pre-filled with oil. straightforward insert the dry filter into the cap and install it. The oil will flow through the filter once the engine starts.
Where do I dispose of the old oil filter?
Most auto parts stores accept used oil filters for free, even if you didn't buy the replacement from them. Some recycling centers also take them. Never throw an oil filter in the trash — it contains residual oil and should be recycled or disposed of properly.