Where the oil filter sits on your 2013 Optima
The oil filter on a 2013 Kia Optima is mounted on the driver's side of the engine, below the intake manifold and tucked behind the engine block. You'll access it from underneath the car, not from the top. This placement means you'll need to either lift the vehicle on a jack or drive it onto ramps, and you'll be working from below rather than from the engine bay.
The filter itself is a cylindrical cartridge about 3 inches tall, held in place by a plastic housing with a cap you turn by hand. Unlike some vehicles where you unscrew a spin-on filter, the Optima uses a cartridge design—you remove the cap, pull out the old filter element, and drop in a new one. This design is common on newer Kias and Hyundais and actually makes the job cleaner because the old filter stays contained inside the housing.
Key Takeaways
- The 2013 Optima's oil filter cartridge sits low on the driver's side of the engine and requires access from underneath the vehicle.
- You turn the plastic housing cap counterclockwise by hand to remove it, then pull out the old filter element and replace it with a new one.
- The correct replacement filter is Kia part number 26300-35503 or equivalent aftermarket cartridge filters rated for your engine size.
- Changing the filter takes 10 to 15 minutes once you have the vehicle safely lifted, and you should replace the rubber seal on the housing cap every time.
What filter type and part number your Optima needs
Kia's original equipment filter for the 2013 Optima is part number 26300-35503. This is a cartridge-style filter, not a spin-on, and it's the part you'll find listed in your owner's manual and service records. If you're buying a replacement, ask for this part number or ask the parts counter to confirm the filter is a cartridge type for a 2013 Optima—this prevents confusion with spin-on filters from other vehicles.
Aftermarket filters from brands like Fram, Mobil 1, and Bosch make cartridge replacements that fit the same housing. When you buy an aftermarket filter, verify on the package that it's designed for a 2013 Kia Optima and that it's a cartridge, not a spin-on. The housing itself rarely needs replacement unless it's cracked or the threads are stripped, which is uncommon.
How to access and remove the old filter
Start by safely lifting the vehicle. Use jack stands if you're using a floor jack—never work under a car supported only by a jack. If you have ramps, drive the front wheels up onto them and set the parking brake. You need enough clearance to reach the filter housing from underneath without lying flat on your back in an awkward position.
Once you're under the vehicle, locate the cylindrical plastic housing on the driver's side of the engine block. It's roughly the size of a soda can and has a large cap on top. Turn the cap counterclockwise by hand—it should come off without tools, though it may be tight if it hasn't been serviced in a while. If it won't budge, use an oil filter wrench or a strap wrench to get it started, then finish by hand.
When the cap comes off, the old filter element will be inside. Pull it straight out and dispose of it. Some oil will drip from the housing, so have a drain pan or old towel underneath. Wipe the inside of the housing clean with a paper towel to remove any debris or old filter material.
Installing the new filter and seal
Before you install the new filter, look at the rubber seal on the underside of the plastic cap. This seal is a small rubber ring that sits in a groove. If it looks cracked, hardened, or flattened, replace it—Kia sells replacement seals separately, or many aftermarket filter kits include a new seal. A worn seal can cause oil leaks around the housing cap.
If you're reusing the old seal, wipe it clean and make sure it sits properly in the groove. Slide the new filter element into the housing—it should drop in easily and sit flat on the bottom. The filter has a rubber seal on its top end that will compress slightly when you screw the cap back on.
Thread the cap back onto the housing by hand, turning clockwise. Tighten it firmly but do not over-tighten—hand-tight is the correct torque for this housing. Over-tightening can crack the plastic cap or damage the seal. Once the cap is snug, you're done with the filter replacement.
Why the cartridge design matters for your maintenance
The cartridge filter design on your Optima is cleaner and more contained than a spin-on filter. When you remove the old filter, it stays inside the housing rather than dripping oil all over the engine bay. This also means less mess when you dispose of the old filter. However, it does require you to work from underneath the vehicle, which is why many owners take their Optima to a shop for oil changes rather than doing it themselves.
The trade-off is that you must replace the rubber seal on the cap periodically. A worn seal is the most common source of oil leaks at the filter housing. If you notice oil seeping from around the cap after an oil change, the seal is likely the culprit, not the filter itself. Replacing just the seal costs a few dollars and takes two minutes.
Tools and supplies you'll need
To change the filter yourself, gather a new filter cartridge, a replacement seal (optional but recommended), a drain pan or towels, jack stands or ramps, a flashlight, and paper towels. An oil filter wrench or strap wrench is helpful if the cap is stuck, but many people can remove it by hand. You do not need special tools to complete this job, though a lift or ramps make it much more comfortable than lying on your back.
If you're changing the oil at the same time, you'll also need new oil, an oil drain plug wrench, and an oil drain pan. The oil drain plug is separate from the filter housing and sits at the bottom of the oil pan on the underside of the engine.
Frequently Asked Questions
Can I change the filter without lifting the car?
Technically yes, but it's uncomfortable and unsafe. The filter sits low enough that you can reach it if you lie on your back under the engine, but you have no protection if the car shifts or falls. Ramps or jack stands are the safer choice and only add 5 minutes to the job.
How often should I replace the filter on a 2013 Optima?
Kia recommends replacing the oil filter every time you change the oil. For a 2013 Optima, that's typically every 10,000 miles or once a year, whichever comes first. Check your owner's manual for the exact interval for your engine size and driving conditions.
What happens if I over-tighten the filter cap?
Over-tightening can crack the plastic housing or damage the rubber seal, both of which cause oil leaks. Hand-tight is correct—if the cap is snug and doesn't turn anymore, stop. You don't need a wrench to finish tightening it.
Is the rubber seal reusable or does it need to be replaced every time?
The seal can last through several oil changes, but it hardens over time. Replacing it every other oil change or whenever it looks cracked or flattened prevents leaks. A new seal costs a few dollars and takes 30 seconds to install.
Where do I dispose of the old filter?
Most auto parts stores accept used oil filters for free, and some recycling centers do as well. Call ahead to confirm. Never throw an oil filter in the trash—it contains residual oil and is considered hazardous waste in most places.