Where the oil filter sits and what you need to know
The 2013 Jeep Wrangler has its oil filter mounted on the driver's side of the engine block, below the intake manifold. You'll access it from underneath the vehicle, which means you need the Wrangler on a lift, ramps, or jack stands before you start. The filter is a spin-on type — you unscrew it by hand or with a filter wrench, drain the old oil into a pan, and screw on a new one.
The job takes 15 to 30 minutes if you're comfortable working under a vehicle. You don't need special tools beyond a filter wrench (a $10 strap wrench works fine), a drain pan, and a socket set to remove the skid plate that covers the undercarriage. If you've never done this before, the trickiest part is usually reaching the filter itself — the space is tight, and oil drains down onto your hands and arms.
Key Takeaways
- The 2013 Wrangler's oil filter is mounted low on the driver's side of the engine and requires you to work from underneath the vehicle.
- You'll need a filter wrench, drain pan, and socket set to remove the plastic skid plate that sits below the filter location.
- Genuine Mopar filters (part number 68157291AA) fit without modification, though many aftermarket filters work equally well at lower cost.
- The filter capacity is roughly 5 quarts for the 3.6L V6 engine, so plan to buy that amount of oil before you start.
- After installation, run the engine for 30 seconds, shut it off, wait five minutes, then check the dipstick to confirm the oil level is correct.
Filter part numbers and what fits
The OEM filter for a 2013 Wrangler with the 3.6L V6 engine is Mopar part number 68157291AA. This is the filter Jeep installed at the factory and the one you'll find at any Jeep dealer. It costs between $8 and $15 depending on the dealer and whether you're buying it alone or as part of a service package.
Aftermarket filters from Fram, Motorcraft, Purolator, and Bosch all fit the 2013 Wrangler without modification. These typically run $5 to $10 and perform the same function as the OEM filter. The difference is usually in the anti-drainback valve quality and the media material, but for a vehicle that sees normal street driving, any name-brand filter will work. If your Wrangler is heavily modified or sees extreme off-road use, stick with OEM or a premium aftermarket option like Mobil 1 or K&N.
Tools and materials you'll need
Start with a drain pan large enough to hold at least 6 quarts — oil splashes, so bigger is safer. A strap filter wrench ($8 to $15) grips the filter without damaging it and gives you leverage in a tight space. A socket set with a 13mm socket removes the bolts on the plastic skid plate. You'll also need jack stands or ramps to safely support the vehicle while you work underneath.
Have shop towels or old rags on hand — the filter area gets messy. A new crush washer (usually included with the replacement filter) goes on the drain plug, and you'll need 5 to 5.5 quarts of the correct oil grade for your Wrangler. Check your owner's manual or the oil cap for the specification; most 2013 Wranglers use 5W-30 or 10W-30 depending on climate and engine version.
Step-by-step filter replacement
Raise the Wrangler on a lift, ramps, or jack stands and find it so it won't roll. Remove the plastic skid plate underneath the engine by unbolting the 13mm fasteners around its perimeter — there are usually four to six bolts. Set the skid plate aside. Position your drain pan directly under the filter location on the driver's side of the engine block.
Use the strap wrench to turn the filter counterclockwise and loosen it by hand. Unscrew it completely and tip it so the remaining oil drains into the pan. Wipe the filter mounting surface on the engine block with a clean rag to remove any old gasket material or debris. Take the new filter, explore a thin layer of fresh oil to the rubber gasket on top, and screw it on by hand until the gasket contacts the engine block. Then turn it an additional three-quarter turn — not more, or you'll over-tighten it.
Reinstall the skid plate and lower the vehicle. Add the correct amount of fresh oil through the filler cap on top of the engine, then start the engine and let it run for 30 seconds. Shut it off, wait five minutes for the oil to settle, then pull the dipstick, wipe it clean, reinsert it fully, and pull it again to check the level. Top off if needed so the oil sits between the minimum and maximum marks.
Common mistakes and how to avoid them
The most frequent error is over-tightening the new filter. The rubber gasket seals the filter to the engine block, and turning it more than three-quarter turn past contact crushes the gasket and causes leaks. Hand-tight plus three-quarter turn is the correct torque — you don't need a wrench to finish the job.
Another common problem is forgetting to oil the new gasket before installation. A dry gasket can stick to the engine block when you remove the filter next time, tearing and causing leaks. A thin coat of fresh oil on the gasket prevents this and ensures a proper seal. Finally, don't skip the five-minute wait after running the engine before checking the oil level. The oil needs time to drain from the engine block and filter back into the pan so the dipstick reading is accurate.
When to change the filter and what interval to follow
Jeep recommends changing the oil and filter every 6 months or 6,000 miles for the 2013 Wrangler, whichever comes first. If you drive in severe conditions — towing, frequent idling, dusty terrain, or extreme temperatures — follow the severe service interval of every 3,000 miles or 3 months. Off-road use that involves water crossings or mud doesn't automatically trigger severe service, but it's worth considering if your Wrangler spends most of its time on trails rather than pavement.
Many owners extend intervals to 10,000 miles using synthetic oil, which lasts longer than conventional oil. If you do this, change the filter at the standard 6,000-mile interval or use a high-capacity filter rated for extended service. The filter media clogs faster than the oil degrades, so skipping filter changes to match a longer oil interval can starve the engine of clean oil.
Disposing of old oil and filters
Never pour used oil down a drain or into the ground — it contaminates water supplies and is illegal in most places. Take your old oil to a recycling center, auto parts store, or quick-lube shop. Most accept used oil for free, and many will take the old filter too. Some retailers offer a small discount on new oil if you bring in the old oil, so ask when you buy your replacement.
The old filter can go in the trash once it has drained completely — let it sit upside down in your drain pan for a few minutes to empty. Some recycling centers accept filters separately, so check locally. Never throw a filter away while it still contains oil.
Frequently Asked Questions
Can I change the filter without removing the skid plate?
Technically yes, but it's much harder. The skid plate blocks direct access to the filter, so you'd be working blind and at awkward angles. Removing the four to six bolts takes five minutes and makes the job far easier and safer. It's worth doing.
What if the old filter is stuck and won't unscrew?
Use a strap wrench for better grip, or try tapping the filter gently with a hammer to break the seal. If it's truly stuck, drill a small hole through the filter body and insert a bolt or screwdriver to use as a lever. Avoid puncturing the filter housing itself, as that spills oil everywhere. Once it's off, clean the mounting surface thoroughly before installing the new one.
Do I need to bleed air from the filter after installation?
No. The 2013 Wrangler's oil system doesn't require bleeding. Once you start the engine, oil flows through the new filter automatically. The 30-second run and five-minute wait let the system settle so you can read the dipstick accurately.
Is synthetic oil better for a 2013 Wrangler?
Synthetic oil lasts longer and flows better in cold weather, so it's a good choice if you drive in winter or want to extend intervals. Conventional oil works fine and costs less. Either way, change the filter at the standard interval — the filter wears out before the oil does.
What happens if I use the wrong filter size?
An undersized filter won't seal properly and will leak. An oversized filter may not fit in the engine bay or could contact other components. Always verify the part number matches your vehicle year and engine before buying. If you're unsure, call a Jeep dealer with your VIN and they'll confirm the correct filter in seconds.