The 2013 Sonata uses a cartridge-style oil filter mounted on top of the engine

The 2013 Hyundai Sonata's oil filter is not a spin-on canister like many older cars. Instead, it's a cartridge filter that sits inside a plastic housing on the top of the engine, near the front. This design is common on modern Hyundais and requires a different removal process than traditional filters, but the job is still straightforward if you know where to look and what tools you need.

You'll find the filter housing directly above the engine block, toward the passenger side. It's a white or translucent plastic cap about 3 inches across. Once you locate it, you can unscrew the cap by hand or with a filter wrench, pull out the old cartridge, and drop in a new one—the whole process takes about 10 minutes once you have the right filter on hand.

Key Takeaways

  • The 2013 Sonata uses a cartridge-style filter in a plastic housing on top of the engine, not a traditional spin-on filter.
  • You will need a new cartridge filter, a new rubber O-ring seal, fresh oil, and either a filter wrench or a 74mm socket to remove the housing cap.
  • The filter housing is located on the top of the engine block toward the passenger side, clearly visible once you open the hood.
  • Replacing the filter takes about 10 minutes and requires no special skills, but using the correct filter part number prevents leaks and engine damage.

What filter part number your Sonata needs

Hyundai part number 26300-35503 is the OEM cartridge filter for all 2013 Sonatas, regardless of engine size (2.0L turbo, 2.4L, or 2.0L diesel in some markets). This is the filter Hyundai installs at the factory and the one most mechanics will recommend.

Aftermarket brands like Fram, Bosch, and Mobil also make cartridge filters that fit the 2013 Sonata. These are usually cheaper than the OEM part and work just as well if you buy from a reputable brand. Check the box or product listing to confirm it's listed as compatible with a 2013 Hyundai Sonata—cartridge filters vary by engine, so buying the wrong one will not fit.

You will also need a replacement O-ring seal (Hyundai part 26315-2F000 or an equivalent rubber gasket). The old seal gets compressed and can leak if you reuse it, so always install a fresh one.

Tools and supplies you will need

To remove the filter housing cap, you have two options: a 74mm oil filter socket (the most common size for this job) or a filter wrench with a strap or chain grip. A socket is faster and less likely to slip, but a wrench works if that's what you have. Do not try to unscrew the cap by hand—it's usually too tight and you risk stripping the plastic threads.

You'll also need a drain pan to catch old oil that spills when you remove the housing, fresh oil (check your owner's manual for the correct grade and amount), a rag or paper towels, and a small brush or pipe cleaner to wipe out the inside of the housing before installing the new filter. If you're changing the oil at the same time, you'll need a drain plug wrench as well.

Step-by-step removal and installation

Step 1: Warm the engine and locate the filter housing. Start the car and let it idle for a minute or two to warm the oil, then turn it off. Wait a few minutes for the oil to cool slightly so you don't burn yourself. Open the hood and look toward the top of the engine on the passenger side—you'll see a white or translucent plastic cap about 3 inches across. This is the filter housing.

Step 2: Remove the housing cap. Place your drain pan underneath the housing to catch any oil that spills. Use your 74mm socket and a ratchet (or a filter wrench) to turn the cap counterclockwise. It will take some force the first time. Once it's loose, you can unscrew it by hand. Lift the cap straight up and out.

Step 3: Remove the old filter and seal. Inside the housing, you'll see the cartridge filter standing upright. Grab it by the top and pull it straight out. The old rubber O-ring seal will either come out with the filter or stay stuck to the inside of the housing cap. Remove it and discard both the old filter and the old seal.

Step 4: Clean the housing. Use a rag or paper towel to wipe out the inside of the housing, removing any dirt or old oil residue. A small brush or pipe cleaner works well for the grooves where the O-ring sits. This step prevents debris from getting into your fresh oil.

Step 5: Install the new seal and filter. Place the new O-ring seal into the groove on the inside of the housing cap, making sure it sits flat all the way around. Slide the new cartridge filter into the housing, pushing it down until it stops. The filter should sit flush with the top of the housing.

Step 6: Reinstall the housing cap. Screw the cap back onto the housing by hand first, then use your socket or wrench to tighten it. Snug it firmly but do not over-tighten—you can crack the plastic housing. A good rule is to tighten until you feel resistance, then turn another quarter turn.

Step 7: Check your work. Start the engine and let it run for 30 seconds, then turn it off. Wait a minute and check around the housing cap for any oil leaks. If you see drips, the seal may not be seated correctly—turn off the engine, let it cool, and check that the O-ring is in the groove and the cap is tight.

Common mistakes that cause leaks or damage

The most common error is forgetting to install the new O-ring seal or reusing the old one. The seal compresses over time and loses its grip, so old seals almost always leak. If you skip this step, you'll lose oil and damage the engine. Always buy a new seal with your filter.

Over-tightening the housing cap is the second mistake. The cap is plastic and the threads are straightforward to strip. Tighten it until snug, then stop—you do not need to crank it down hard. If you strip the threads, you'll have to replace the entire housing, which is much more expensive than the filter itself.

Installing the wrong filter size is rare but possible if you order online without checking the part number. A filter that does not fit will either not seat properly or will not fit in the housing at all. Always confirm the part number matches your 2013 Sonata before you buy.

When to replace your oil filter

Hyundai recommends replacing the oil filter every time you change the oil. For a 2013 Sonata, that's typically every 5,000 to 10,000 miles, depending on your driving conditions and the type of oil you use. Check your owner's manual for the exact interval for your car—severe driving (lots of short trips, towing, or dusty conditions) may call for more frequent changes.

If you hear a rattling noise from the engine or see an oil pressure warning light on the dashboard, the filter may be clogged or the seal may be leaking. Stop driving and check the filter housing for leaks or the filter itself for damage. A clogged filter restricts oil flow and can damage the engine if ignored.

Frequently Asked Questions

Can I use a spin-on filter instead of the cartridge filter?

No. The 2013 Sonata is designed for a cartridge filter only. Spin-on filters do not fit the housing, and trying to adapt one will cause leaks or engine damage. Stick with the cartridge filter.

What happens if I over-tighten the housing cap?

You risk cracking the plastic housing or stripping the threads. If the threads strip, the cap will not seal and oil will leak out. You'll then have to replace the entire housing, which costs much more than the filter. Tighten until snug, then stop.

Do I need to change the oil every time I change the filter?

No, but Hyundai recommends changing both at the same time. If you're only replacing the filter between oil changes, you can do that—just make sure you're not overdue for an oil change based on your mileage or the time since your last one.

Where do I dispose of the old filter and oil?

Take used oil and the old filter to a recycling center, auto parts store, or quick-lube shop. Most accept them for free. Do not pour oil down the drain or throw the filter in the trash—both harm the environment and are illegal in most places.

How much oil will spill when I remove the filter housing?

Usually just a few ounces, enough to fill a drain pan a quarter of the way. The cartridge filter itself does not hold much oil. If you're changing the oil at the same time, you'll drain much more from the drain plug.