The 2013 CR-V uses a cartridge-style oil filter mounted on top of the engine
The 2013 Honda CR-V has an oil filter that sits in a plastic housing on the top of the engine, not a spin-on filter screwed to the side like older vehicles. The filter element itself is a flat, accordion-shaped cartridge that you pull straight up out of the housing. This design is common on newer Hondas and means you do not need a filter wrench — just your hands and a new rubber O-ring seal.
The filter housing is located on the driver's side of the engine, toward the back. You can see it clearly once you open the hood. It is a black plastic cap about the size of a soda can. The whole job takes 10 to 15 minutes if you are changing the filter alone, or about 30 minutes if you are also draining and refilling the oil.
Key Takeaways
- The 2013 CR-V filter is a cartridge type housed in a plastic cap on top of the engine, not a spin-on filter.
- You will need a new filter cartridge, a replacement O-ring seal, and a filter wrench or cap socket to remove the housing — not a traditional oil filter wrench.
- The filter housing cap requires a 74 mm socket or a dedicated Honda filter wrench to unscrew; a standard wrench will slip.
- Always replace the rubber O-ring seal when you change the filter, because reusing the old one can cause leaks.
What you need to buy for a 2013 CR-V oil filter change
The OEM (original equipment manufacturer) filter for a 2013 CR-V is Honda part number 15400-PLM-A01. Aftermarket equivalents are widely available from auto parts stores and online retailers. The filter itself costs between $8 and $15 depending on the brand. You will also need a replacement O-ring seal, which Honda sells as part number 91301-PLC-003 or 91301-PLC-901. Many filter kits include both the cartridge and the O-ring together for $12 to $20.
To remove the housing cap, you need either a 74 mm oil filter socket (about $10 to $15) or a Honda-specific filter wrench. A standard adjustable wrench or pipe wrench will slip on the plastic cap and damage it. If you plan to change your own oil regularly, the socket is a worthwhile investment. If this is a one-time job, you can borrow one from a friend or rent one from an auto parts store for a few dollars.
Step-by-step filter replacement
Start with a cold engine or let it cool for at least five minutes after running. Locate the filter housing cap on the top of the engine on the driver's side. Place a drain pan underneath it — there will be some oil in the housing. Using your 74 mm socket and a ratchet, turn the cap counterclockwise to unscrew it. It will come off in your hand.
Pull the old filter cartridge straight up and out of the housing. It will be wet with oil. Discard it. Look inside the housing and wipe out any debris or old rubber bits with a clean rag. Locate the rubber O-ring seal on the underside of the cap — it is a small black ring. Peel it off and throw it away. Slide the new O-ring onto the cap, making sure it sits in the groove all the way around.
Insert the new filter cartridge into the housing, pushing it down until it seats. Screw the cap back on by hand first, then tighten it with your socket. Do not over-tighten — snug is enough. Wipe up any spilled oil. Start the engine and let it run for a few seconds, then turn it off and wait a minute. Check the oil level on the dipstick and top up if needed.
Common mistakes that cause leaks
The most frequent problem is reusing the old O-ring seal. The rubber hardens over time and loses its grip, so oil seeps out around the cap. Always install a fresh O-ring every time you change the filter. The second mistake is over-tightening the cap. The plastic housing can crack if you crank too hard. Hand-tight plus a quarter turn with the socket is the right amount.
A third issue is forgetting to seat the filter cartridge all the way down before screwing the cap back on. If the cartridge is not fully inserted, the O-ring will not compress properly and you will have a leak. Push the cartridge down until you feel it stop, then install the cap.
Where to buy a 2013 CR-V oil filter
Auto parts chains like AutoZone, O'Reilly, NAPA, and Advance Auto Parts stock both OEM Honda filters and aftermarket brands in-store and online. Amazon and eBay also carry them, though shipping times vary. Walmart and Costco carry basic filters if you have a membership. The OEM Honda filter is usually the most expensive option but is may provide to fit. Reputable aftermarket brands like Fram, Mobil 1, and Bosch work well and cost less.
If you are unsure which filter to order online, use the part number 15400-PLM-A01 or enter your vehicle information (2013 Honda CR-V) into the parts store website and it will show you compatible options. Many stores offer free in-store pickup within a day or two, which is faster than waiting for shipping.
When to change your 2013 CR-V oil filter
Honda recommends changing the oil filter every time you change the engine oil. For a 2013 CR-V, that is typically every 10,000 miles or once a year, whichever comes first, if you use synthetic oil. If you use conventional oil, the interval is usually 5,000 to 7,500 miles or every six months. Check your owner's manual for the exact interval for your driving conditions.
If you are not sure when your last filter change was, look at the oil change sticker on the driver's side of the windshield or in the door jamb. It will show the mileage and date. If it has been more than a year or the mileage is more than 10,000 miles ago, it is time to change the filter.
Frequently Asked Questions
Can I change the oil filter without changing the oil?
Yes, you can change just the filter. However, the filter housing will still contain some old oil that will drain into your pan, so have one ready. Most people change both at the same time because you are already under the hood and the labor is the same.
What if the filter cap is stuck and won't unscrew?
explore penetrating oil like WD-40 around the cap and let it sit for 15 minutes. Make sure you are using the correct 74 mm socket — a wrench that is too small will slip and round the edges. If it is still stuck, tap the socket gently with a hammer to help it grip, then try again.
Is the OEM Honda filter worth the extra cost?
OEM filters are made to Honda's exact specifications and are may provide to fit. Reputable aftermarket brands work just as well and cost less. Either choice is fine as long as you buy from a known brand and replace the O-ring every time.
How much oil will spill when I remove the filter cap?
Usually less than a cup, but it depends on how long the engine has been off. A cold engine will have more oil in the housing. Always place a drain pan underneath before you unscrew the cap to catch the spill.
Do I need to reset anything after changing the filter?
No. The 2013 CR-V does not have an oil filter change reminder light. Once you finish, just start the engine and check that the oil pressure light goes out within a few seconds. If it stays on, turn off the engine and check your oil level.