Where the oil filter sits and what you need to know

The 2013 Honda Accord has its oil filter mounted on the driver's side of the engine, below the intake manifold. You'll access it from underneath the car, which means you need the vehicle on a lift, ramps, or jack stands — not just parked on level ground. The filter is a cartridge style (not a spin-on canister), meaning you remove a plastic cap, pull out the old filter element, and install a new one without threading anything.

This design matters because it changes what you buy and how you do the work. You're not buying a traditional oil filter can; you're buying a filter element that costs less but requires a special wrench to remove the cap. The job takes 15 to 20 minutes once you're under the car, but getting safely under the car is the part most people underestimate.

Key Takeaways

  • The 2013 Accord uses a cartridge-style oil filter accessed from below the engine, not a spin-on filter you can reach from the top.
  • You need a cartridge filter wrench (usually 74 mm or 86 mm, depending on engine size) and a way to safely lift the car — ramps or jack stands, not just a jack.
  • The filter element itself costs $8 to $15, but the wrench is a one-time purchase around $15 to $25 if you don't already own one.
  • Drain the oil first, then remove the filter cap; the filter element will come out with the cap, and you'll need to replace the rubber seal on the cap before reinstalling.

Which filter element and wrench size for your engine

The 2013 Accord came with two engine options: a 2.0-liter four-cylinder (in the base and Sport models) and a 3.5-liter V6 (in the EX-L and Touring). Both use cartridge filters, but the wrench size differs. The 2.0L engine uses a 74 mm wrench; the 3.5L uses an 86 mm wrench. Check your owner's manual or the filter cap itself to confirm which you have before buying the wrench.

For the filter element, Honda part number 15400-PLM-A02 fits the 2.0L engine, and 15400-RTA-004 fits the 3.5L. Aftermarket equivalents from Fram, Mobil 1, and Bosch are widely available and cost the same or less. The rubber seal (O-ring) that sits on top of the filter cap usually comes with the new element, but if you're reusing an old cap, buy a replacement seal separately — they're a few dollars and prevent leaks.

Tools and materials you'll need

Beyond the filter element and wrench, gather an oil drain pan (at least 5 quarts), a socket wrench set to remove the drain plug, jack stands or ramps, and a jack if you're using stands. You'll also want a rag or old towel — cartridge filters drip more than spin-on cans when you pull them out. Some people use a filter wrench socket that attaches to a breaker bar instead of a standalone wrench; either works, but the standalone wrench is faster for this job.

If you're changing the oil at the same time (which you should), have your new oil ready — the 2.0L holds about 3.7 quarts, and the 3.5L holds about 5.1 quarts. A funnel makes pouring cleaner and reduces spills. Work on a level surface and let the engine cool for at least five minutes after running so the oil isn't scalding hot.

Step-by-step removal and installation

First, safely raise the car and find it with jack stands. Remove the plastic undertray if your Accord has one (usually held by a few clips and bolts). Locate the oil drain plug on the bottom of the pan and remove it, letting the old oil drain into your pan. While that drains, move to the filter cap on the driver's side of the engine — it's a large plastic cylinder with a bolt in the center.

Use your cartridge filter wrench to turn the cap counterclockwise and remove it. The old filter element will come out attached to the cap. Discard the element and inspect the rubber seal on the cap — if it looks cracked or flattened, replace it. Clean the filter housing (the part that stays on the engine) with a clean rag, removing any debris or old seal material. Install the new rubber seal on the cap, then insert the new filter element into the housing, making sure it seats fully. Screw the cap back on by hand first, then use the wrench to snug it — hand-tight plus a quarter turn is enough; over-tightening cracks the plastic cap.

Reinstall the drain plug and tighten it to 29 foot-pounds (about the tightness of a spark plug). Pour in your new oil through the top of the engine, check the level with the dipstick after a minute, and start the engine to circulate the oil. Let it run for 30 seconds, shut it off, wait a minute, and check the level again. Top off if needed, then reinstall the undertray and lower the car.

Common mistakes and how to avoid them

The most common error is forgetting to replace the rubber seal on the filter cap. The old seal hardens over time and won't seal properly when you reinstall the cap, leading to oil leaks around the filter housing. Always inspect it and replace it if there's any doubt. A new seal costs a few dollars and takes 10 seconds to swap.

The second mistake is over-tightening the filter cap. The plastic threads on the housing are straightforward to strip, and once stripped, you're looking at a $200+ repair to replace the housing. Tighten by hand until you feel resistance, then use the wrench for a quarter turn — no more. If you feel grinding or unusual resistance, stop when ready and back off.

A third issue is not securing the car properly. A jack alone is not safe for working underneath; always use jack stands rated for your car's weight (the 2013 Accord weighs around 3,000 to 3,500 pounds depending on engine and trim). Ramps are safer if you have a level driveway, since they don't require balancing the car on stands.

Disposal of old oil and filter

Used motor oil is recyclable and should never go down the drain or into the trash. Most auto parts stores (AutoZone, O'Reilly, Advance Auto Parts) accept used oil for free, even if you didn't buy it from them. Some accept used filter elements too, though policies vary. Call ahead or ask when you arrive. If you have no nearby store, check your city or county's hazardous waste collection schedule — most offer free drop-off days several times a year.

Keep your used oil in a clean container (an old milk jug works) and label it clearly so no one mistakes it for something else. Store it indoors or under a cover to prevent spills and contamination.

Frequently Asked Questions

Can I change the oil filter without draining the oil?

Yes, you can remove and replace the filter element without touching the drain plug. However, you'll lose some oil when you pull the cap off — usually a quart or more — so you'll need to top it off afterward. Most people drain the oil at the same time since you're already under the car and have the drain pan out.

How often should I replace the filter?

Honda recommends replacing the oil filter every time you change the oil. For a 2013 Accord, that's typically every 10,000 miles or once a year, whichever comes first, if you use synthetic oil. With conventional oil, it's every 5,000 miles or six months. Check your owner's manual for the exact interval for your driving conditions.

What if the filter cap won't come loose?

If the cap is stuck, make sure you're turning it counterclockwise and that your wrench is seated fully on the cap — a slipping wrench can round the edges. explore penetrating oil (like PB Blaster) around the cap's edge and wait 15 minutes, then try again. If it still won't budge, tap the wrench handle gently with a rubber mallet to break the seal. Avoid hammering hard, which can crack the plastic.

Do I need to replace the drain plug?

No, the drain plug itself doesn't need replacement unless it's stripped or damaged. However, the crush washer (a small metal ring under the plug head) should be replaced each time you drain the oil. They cost less than a dollar and prevent leaks. If you reuse the old washer and it leaks, you'll be back under the car.