The 2013 Ford Explorer uses a cartridge-style oil filter located on top of the engine
The oil filter on a 2013 Ford Explorer sits in a plastic housing on the driver's side of the engine, near the back. It's a cartridge filter, not a spin-on type, which means you unscrew the cap, pull out the filter element, and replace it—rather than twisting off an entire canister. This design is common on Ford vehicles from that generation and requires a specific tool to remove the housing cap.
You'll need a cartridge filter wrench (usually around 74 mm or 86 mm, depending on your engine size) to unscrew the cap. The filter itself costs between $8 and $15, and the job takes about 15 to 20 minutes once you have the right tool. If you don't own a filter wrench, you can rent one from most auto parts stores for a few dollars, or a shop can do the replacement for $30 to $60 in labor.
Key Takeaways
- The 2013 Ford Explorer has a cartridge-style oil filter in a housing on top of the engine, not a spin-on filter under the car.
- You need a cartridge filter wrench to remove the housing cap; the size depends on whether you have a 3.5L EcoBoost or 3.0L engine.
- The filter element itself costs $8 to $15, and you should replace the rubber O-ring seal on the cap at the same time to prevent leaks.
- If you don't have the wrench, renting one from an auto parts store costs less than paying a shop to do the work.
Which Engine Size you have matters for the wrench size
The 2013 Ford Explorer came with two engine options: the 3.5L EcoBoost and the 3.0L EcoBoost. Both use a cartridge filter, but the housing cap size differs between them. The 3.5L uses an 86 mm wrench, while the 3.0L uses a 74 mm wrench. Check your owner's manual or the engine cover under the hood to confirm which engine you have before buying or renting a wrench.
If you buy the wrong size wrench, it won't fit the cap and you'll waste time and money. Many auto parts stores will let you return an unused wrench, so ask about their return policy before you leave. Some stores also sell a universal cartridge filter wrench that adjusts to fit multiple sizes, though these are less reliable than a fixed-size tool.
Steps to replace the filter yourself
Start by running the engine for a minute or two to warm the oil slightly, then turn it off and wait five minutes. Warm oil drains faster and more completely. Locate the filter housing cap on top of the engine—it's a black plastic cylinder about 3 inches tall on the driver's side, toward the rear of the engine bay.
Place an oil drain pan underneath the housing, then use your cartridge filter wrench to turn the cap counterclockwise. It will loosen and unscrew by hand after a few turns. Lift the cap straight up and out; the old filter element will come out with it. Some oil will spill, so keep the drain pan in place. Remove the rubber O-ring seal from the cap (it's a small ring around the base) and discard it.
Wipe the inside of the housing clean with a lint-free cloth or paper towel. Install the new O-ring seal on the cap—this comes with most replacement filters, or you can buy one separately for $2 to $3. Slide the new filter element into the housing, then screw the cap back on by hand until the O-ring contacts the housing, then turn it an additional three-quarter turn with the wrench. Do not over-tighten; the O-ring does the sealing, not brute force.
Start the engine and let it run for 30 seconds, then turn it off and wait a minute. Check the cap and housing for leaks. If oil is dripping, the cap may not be tight enough or the O-ring may not be seated correctly. Tighten slightly and check again. Once you confirm there are no leaks, dispose of the old filter and O-ring at an auto parts store or recycling center.
What filter part numbers to buy
Ford's OEM (original equipment manufacturer) filter for the 2013 Explorer is part number DG9Z-6714-A. This is the filter element only; the O-ring comes separately as part number DG9Z-6713-A. You can buy both from a Ford dealer, though they are usually more expensive than aftermarket options.
Common aftermarket replacements include Motorcraft (Ford's parts brand, sold at auto parts stores), Fram, Bosch, and Purolator. All of these fit the 2013 Explorer and meet Ford's specifications. Motorcraft filters are typically $10 to $12, while other brands range from $8 to $15. Check the package to confirm it says "cartridge filter" and lists the 2013 Explorer as compatible; spin-on filters will not fit your vehicle.
When to replace the oil filter
Ford recommends replacing the oil filter every time you change the oil. For a 2013 Explorer with the EcoBoost engines, that's every 10,000 miles or 12 months, whichever comes first, under normal driving conditions. If you tow, idle frequently, or drive in dusty conditions, Ford suggests every 5,000 miles or 6 months instead. Check your owner's manual for the exact interval that applies to your driving habits.
The filter housing cap has a small inspection window on the side; if the filter element looks dark or clogged when you look through it, that's a sign it's time for a change even if you haven't hit the mileage interval. A clogged filter restricts oil flow and can damage the engine over time.
Common mistakes to avoid
The most common error is forgetting to replace the O-ring seal. Reusing the old O-ring will cause leaks because it hardens and loses its seal over time. Always install a new one, even if the old one looks fine. The second mistake is over-tightening the cap with the wrench. The O-ring does all the sealing work; tightening beyond the three-quarter turn after hand-tightening can damage the housing or the O-ring itself.
Another frequent problem is using the wrong wrench size. If the wrench doesn't fit snugly on the cap, stop and confirm you have the right size for your engine. Forcing a wrench that's too small or too large can strip the cap and make it impossible to remove later. Finally, some owners forget to drain the old oil from the housing before installing the new filter. This doesn't damage anything, but it means your new oil will be diluted with old oil until the next change.
Frequently Asked Questions
Can I use a spin-on oil filter on a 2013 Ford Explorer?
No. The 2013 Explorer has a cartridge-style filter housing, not a spin-on filter base. A spin-on filter will not thread onto your engine. You must use a cartridge filter element designed for your vehicle.
What happens if I don't replace the O-ring seal?
The old O-ring will harden and lose its grip, allowing oil to leak from the housing cap. You may not notice when ready, but over time the leak will cause oil loss and potentially engine damage. Always install a new O-ring with each filter change.
Do I need to drain the oil pan before changing the filter?
No. The cartridge filter housing is separate from the oil pan, so changing the filter alone does not drain the engine oil. You only need to drain the pan during a full oil change. However, some oil will spill from the housing when you remove the cap, so use a drain pan to catch it.
Can I reuse the old filter element?
No. Oil filters are designed for single use and cannot be cleaned or restored to working condition. A used filter will restrict oil flow and reduce engine protection. Always install a new filter element.
Where do I dispose of the old filter and O-ring?
Most auto parts stores accept used oil filters and O-rings for recycling at no charge. Some recycling centers also take them. Do not throw them in the trash or pour old oil down the drain.