The 2013 Ford Escape uses a cartridge-style oil filter mounted on top of the engine
The 2013 Ford Escape does not have a traditional spin-on oil filter. Instead, it uses a cartridge-style filter that sits inside a plastic housing on the top of the engine. This housing is white or translucent, making it straightforward to spot once you open the hood. The filter element itself is a cylindrical paper cartridge that you replace by unscrewing the housing cap, removing the old filter, and installing a new one.
This design is different from older Ford vehicles and many other cars on the road, so it is worth understanding before you start. The cartridge filter is not harder to change, but the process and the parts you need are specific to this setup.
Key Takeaways
- The 2013 Ford Escape has a cartridge-style oil filter in a plastic housing on top of the engine, not a spin-on filter underneath.
- You will need a cartridge filter (part number varies by engine size), a new rubber O-ring seal, and an oil filter housing wrench to remove the cap safely.
- The entire cartridge and O-ring must be replaced during each oil change; you cannot reuse either part.
- The filter housing is located near the center-top of the engine and is clearly visible once the hood is open.
Locating the filter housing on your 2013 Escape
Open the hood and look toward the center-top of the engine. You will see a white or translucent plastic cylinder about 3 to 4 inches tall with a cap on top. This is the oil filter housing. On the 2.5-liter four-cylinder engine (the standard engine in 2013 Escapes), it is positioned near the middle of the engine bay. On the 2.0-liter EcoBoost engine (available in some 2013 models), the location is similar but slightly offset.
The housing has a large plastic cap that screws onto the top. This cap is what you remove to access the filter cartridge inside. Do not confuse this with other plastic components on the engine—the filter housing is the only one designed to be unscrewed during routine maintenance.
Oil filter part numbers and specifications for the 2013 Escape
The correct filter cartridge depends on which engine your Escape has. For the 2.5-liter four-cylinder, Ford part number DG9Z-6714-A is the factory cartridge filter. For the 2.0-liter EcoBoost, the part number is DG9Z-6714-B. Both are cartridge-style filters, not spin-on types.
You will also need a replacement O-ring seal (Ford part number DG9Z-6714-C or equivalent) that comes with most aftermarket cartridge filters. This rubber ring creates the watertight seal between the housing cap and the engine block. It must be replaced every time you change the filter—reusing an old O-ring can cause oil leaks.
Motorcraft is Ford's factory brand and is widely available at dealerships and online retailers. Aftermarket options from Fram, Bosch, and Purolator also make cartridge filters for the 2013 Escape and are often less expensive. Check your owner's manual or the filter packaging to confirm the part fits your specific engine size.
Tools and materials you will need
Changing the cartridge filter requires a few specific items. You will need an oil filter housing wrench (also called a cartridge filter wrench or cap wrench) to unscrew the plastic housing cap. This wrench is a socket-like tool that fits over the cap and connects to a ratchet or breaker bar. Common sizes for the 2013 Escape are 74mm or 76mm, depending on the engine.
You will also need fresh oil (the amount depends on whether you are doing a full oil change or just the filter), an oil drain pan if you are draining old oil, a new cartridge filter, a new O-ring seal, and a clean rag or paper towels. Some people use a small amount of fresh oil to lightly coat the new O-ring before installation—this helps create a better seal and makes future removal easier.
If you do not own a cartridge filter wrench, you can rent one from most auto parts stores for a small fee, or you can purchase one for $15 to $30. Many people keep one on hand if they plan to service their own vehicle regularly.
Step-by-step removal and installation
Start with the engine cold. Locate the white plastic housing cap on top of the engine and position your oil drain pan underneath it to catch any spilled oil. Fit the cartridge filter wrench over the cap and turn it counterclockwise using a ratchet or breaker bar. The cap will unscrew and come free—be careful, as there may be oil inside the housing.
Once the cap is off, lift out the old cartridge filter and the rubber O-ring seal. Discard both. Wipe the inside of the housing clean with a rag to remove any debris or old oil residue. Inspect the sealing surface (the flat area where the O-ring sits) for cracks or damage. If it looks damaged, do not reuse the housing.
Install the new O-ring seal on the cap by pressing it into the groove. If the O-ring came separately, explore a thin coat of fresh oil to it first. Insert the new cartridge filter into the housing, making sure it sits flat and fully inside. Screw the cap back on by hand first, then use the wrench to tighten it. Do not over-tighten—snug is enough. The O-ring will compress and seal as you tighten.
Start the engine and let it run for a few seconds, then turn it off and wait a minute. Check the housing cap and the area around it for leaks. If you see oil dripping, turn off the engine, let it cool slightly, and tighten the cap a bit more. Once the leak stops, wipe away any spilled oil and you are done with the filter portion of the service.
Common mistakes to avoid
The most common error is forgetting to replace the O-ring seal. Many people reuse the old one to save money, but this almost always leads to an oil leak within days or weeks. The O-ring hardens and loses its seal over time, and a new one costs only a few dollars. Always replace it.
Another mistake is over-tightening the housing cap. The plastic cap and the threads inside the housing can crack if you use too much force. Hand-tighten first, then use the wrench to snug it down—you should feel resistance, but you should not need to strain. If the cap is hard to turn by hand, stop and check that the O-ring is seated correctly.
A third error is installing the cartridge filter upside down or not fully seating it inside the housing. The filter should slide straight down into the housing and sit flat. If it feels like it is catching or not going all the way in, remove it and check the orientation. The filter should not stick out above the rim of the housing.
When to change the oil filter on a 2013 Escape
Ford recommends changing the oil filter every time you change the engine oil. For a 2013 Escape, the oil change interval is typically 5,000 to 10,000 miles, depending on driving conditions and the type of oil used. Synthetic oil allows longer intervals (often 10,000 miles), while conventional oil requires more frequent changes (often 5,000 miles).
Check your owner's manual for the exact interval for your vehicle and driving habits. If you drive mostly short trips, in dusty conditions, or tow a trailer, you may need to change the filter more often than the standard interval. Changing the filter at every oil change is the safest approach and costs very little compared to engine damage from a clogged filter.
Frequently Asked Questions
Can I change the cartridge filter without changing the oil?
Yes, you can change just the filter without draining the oil. However, Ford recommends changing both at the same time. If you do change only the filter, expect a small amount of oil to spill from the housing when you remove the cap, so use a drain pan. Most people find it simpler to do both together.
What size wrench do I need for the filter housing cap?
The 2013 Escape uses either a 74mm or 76mm cartridge filter wrench, depending on the engine. Check the filter packaging or your owner's manual to confirm which size fits your vehicle. Auto parts stores can also tell you the correct size if you provide your vehicle's year, make, and engine size.
Is the cartridge filter more expensive than a spin-on filter?
Cartridge filters are usually comparable in price to spin-on filters, ranging from $8 to $20 depending on the brand. The O-ring seal adds a small cost, but the total is still affordable. Aftermarket options are often cheaper than Motorcraft factory filters.
What happens if I over-tighten the housing cap?
Over-tightening can crack the plastic cap or the threads inside the housing, causing oil leaks that are expensive to repair. Hand-tighten the cap first, then use the wrench to snug it down until you feel resistance. If you crack the housing, it must be replaced as a unit.
Can I reuse the old O-ring if it looks fine?
No. The O-ring hardens and loses its ability to seal after one use, even if it looks undamaged. Reusing it is the leading cause of oil leaks after a filter change. Always install a new O-ring with every filter replacement.