The 2013 Ford Edge uses a cartridge-style oil filter mounted on top of the engine
The 2013 Ford Edge does not have a traditional spin-on oil filter that you unscrew from the side of the engine. Instead, it uses a cartridge filter housed in a plastic cap on top of the engine. This cap sits near the front of the valve cover, and the filter element slides out from inside it. The design is cleaner and takes up less space, but it means the replacement process is slightly different from what you might expect if you have owned other vehicles.
Understanding where this filter sits and how it comes out matters because you need to know what you are working with before you start. If you are doing the work yourself, you need to locate the cap, know how to open it without spilling oil everywhere, and understand which direction the new filter goes in. If you are having it done at a shop, knowing the real location helps you understand what the technician is actually doing and why it takes the time it does.
Key Takeaways
- The 2013 Ford Edge has a cartridge-style oil filter in a plastic cap on top of the engine, not a spin-on filter on the side.
- You will need an oil filter wrench sized for the cap (usually 74 mm or 86 mm depending on engine size) and a drain pan to catch oil that spills when you open the cap.
- The filter element itself is a flat, accordion-shaped piece that slides straight out and must be replaced with the correct part number for your engine size.
- Replacing the filter takes 10 to 15 minutes once you have the right tools and understand the layout, and it should be done every time you change the oil.
Locating the filter cap on your 2013 Edge
Open your hood and look toward the front of the engine, near the driver's side. You will see a black plastic cap with a center bolt or nut on top of it. This cap sits directly on the valve cover. On the 2.0-liter EcoBoost engine, the cap is smaller and sits more toward the center-front of the engine. On the 3.5-liter V6 engine, the cap is larger and sits slightly more to the driver's side. Either way, it is the most obvious cylindrical plastic housing on top of the engine block.
The cap is connected to the engine with a single bolt or nut in the center. When you remove this fastener, the entire cap lifts straight up and off. Inside the cap is where the filter element lives. The cap itself contains a spring and a rubber seal that keep oil from leaking out when the engine is running. When you open it, oil will drip, so position your drain pan underneath before you loosen anything.
Tools and parts you will need
You need an oil filter wrench that fits the cap. Ford Edge filter caps typically use either a 74 mm or 86 mm wrench, depending on your engine. The 2.0-liter EcoBoost usually takes a 74 mm wrench, and the 3.5-liter V6 usually takes an 86 mm wrench. You can find these wrenches at any auto parts store for $10 to $20. Some shops use a strap wrench instead, which works on any size but requires more hand strength. If you are doing this yourself, the socket-style wrench is easier.
You will also need a new filter element. Ford part numbers vary by engine: the 2.0-liter EcoBoost uses part number DG9Z-6714-A or equivalent, and the 3.5-liter V6 uses DG9Z-6714-B or equivalent. Always verify the correct part for your specific engine before you buy. You will need a drain pan large enough to catch 1 to 2 quarts of oil, rags or paper towels, and fresh oil to top up the reservoir after you finish. Wear gloves to keep oil off your hands.
How to remove and replace the filter element
Position your drain pan under the filter cap. Use the oil filter wrench to loosen the center bolt on top of the cap by turning it counterclockwise. Once it is loose enough to turn by hand, unscrew it the rest of the way and set it aside. Carefully lift the plastic cap straight up and off the engine. Oil will drip from the cap and from the opening on the engine, so let it drain into the pan for a few seconds.
Inside the cap, you will see the filter element—a flat, pleated piece that looks like an accordion. It is held in place by a center post. Grab the element by its edges and pull it straight out. Do not twist it or force it; it should slide out cleanly. Inspect the rubber seal on the underside of the cap. If it looks cracked, hardened, or damaged, it should be replaced along with the filter. Most shops replace the seal as part of routine maintenance.
Slide the new filter element into the cap, making sure the center post goes through the hole in the middle of the element. The pleated sides should sit flat against the inside walls of the cap. Place the cap back on the engine opening and hand-tighten the center bolt. Once it is snug, use the wrench to tighten it an additional one-quarter to one-half turn. Do not over-tighten; the seal will compress and hold the cap in place without excessive force.
Why the cartridge design matters for maintenance
Cartridge filters are sealed inside a cap, which means they stay cleaner and are less likely to leak during installation. The design also reduces the amount of oil that spills during a change because the filter element itself does not hold as much oil as a traditional spin-on filter. However, the trade-off is that you must be careful not to lose the rubber seal when you open the cap, and you need the correct wrench size to avoid stripping the bolt.
The cartridge design also means the filter is harder to access if you are working in a tight engine bay. On some Edge models, you may need to remove the air intake or other components to get a clear angle on the cap. This is one reason why many owners choose to have this service done at a shop rather than doing it themselves. A technician with the right tools and experience can complete the job quickly without risk of damaging the seal or cross-threading the bolt.
Common mistakes to avoid
The most common mistake is over-tightening the center bolt. The bolt does not need to be cranked down hard; it only needs to compress the rubber seal enough to hold the cap in place. Over-tightening can crack the seal or strip the threads on the bolt, and then you have a leak that is expensive to fix. Tighten it snug, then add one-quarter turn with the wrench and stop.
Another mistake is installing the filter element backwards or not seating it fully. The element must slide all the way down onto the center post, and the pleats must sit flat inside the cap. If you force the cap back on and the element is not seated, you can damage the pleats or the seal. Take a moment to make sure the element is sitting correctly before you reinstall the cap.
A third mistake is forgetting to top up the oil after you finish. When you remove the filter cap, you lose some oil. After you reinstall the cap and run the engine briefly to circulate the new filter, check the oil level and add oil if needed. Running the engine low on oil, even for a short time, can damage the engine.
When to replace the filter during an oil change
The filter should be replaced every time you change the oil. On a 2013 Ford Edge, Ford recommends an oil change interval of 10,000 miles under normal driving conditions, or 5,000 miles if you drive in severe conditions (frequent short trips, towing, dusty environments, or extreme temperatures). The filter cannot be cleaned or reused; it must be replaced with a new one each time.
If you go longer than the recommended interval between oil changes, the filter becomes saturated with contaminants and loses its ability to trap particles. This means dirt and metal particles circulate through the engine, causing wear on bearings, pistons, and valve components. Replacing the filter on schedule is one of the cheapest ways to extend engine life and avoid costly repairs down the road.
Frequently Asked Questions
Can I use any cartridge filter, or does it have to be a Ford part?
You should use a filter that matches your engine size and is rated for the 2013 Edge. Ford OEM filters are reliable, but quality aftermarket filters from brands like Motorcraft, Fram, or Bosch also work well. The key is matching the part number to your specific engine (2.0 EcoBoost or 3.5 V6) and making sure the filter is designed for that process. Using the wrong size or type can cause leaks or poor filtration.
What should I do if the rubber seal sticks to the engine and does not come off with the cap?
If the seal stays on the engine instead of coming off with the cap, use a plastic scraper or old credit card to gently pry it off. Do not use a metal tool, which can scratch the sealing surface. Once you remove the old seal, clean the surface with a rag and inspect it for damage. Install the new seal that comes with the replacement filter cap, or purchase a seal kit separately if your filter element did not include one.
How much oil will spill when I open the filter cap?
Expect 1 to 2 quarts of oil to drain from the cap and engine opening. This is less than a full oil change, but enough to make a mess if you do not have a drain pan ready. Position the pan directly under the cap before you loosen the bolt, and let the oil drain for 10 to 15 seconds after you remove the cap. Wipe up any spills with rags or paper towels to prevent slipping and to keep the engine bay clean.
Do I need to replace the rubber seal every time I change the filter?
The seal should last several oil changes, but it is a good idea to inspect it each time you open the cap. If it looks cracked, hardened, or damaged, replace it. Many shops include a new seal with the replacement filter cap, or you can purchase a seal kit for $5 to $10. Replacing the seal preventively every other oil change is also a reasonable practice if you want to avoid leaks.
What is the difference between the 2.0 EcoBoost and 3.5 V6 filter caps?
The 2.0-liter EcoBoost filter cap is smaller and uses a 74 mm wrench. The 3.5-liter V6 cap is larger and uses an 86 mm wrench. The filter elements are also different sizes and part numbers. If you have the wrong wrench, you will not be able to remove the cap without damaging it. Check your owner's manual or the cap itself to confirm which engine you have before you buy tools or parts.