What oil filter fits a 2013 F-150 with the 5.0L engine

The 2013 Ford F-150 with the 5.0L V8 engine uses a Motorcraft FL-820S oil filter, which is Ford's factory-spec filter for this truck. This is a spin-on filter that threads directly onto the engine block below the intake manifold on the driver's side. The filter is roughly 3 inches in diameter and 4.5 inches tall, so it fits in the tight engine bay without interfering with other components.

If you cannot find the Motorcraft FL-820S or prefer an aftermarket option, several manufacturers make direct replacements that meet Ford's specifications. Common alternatives include the Fram PH8A, Bosch 3330, and Wix 51515. All of these filters have the same thread size (3/4-16 UNF), bypass valve rating, and micron filtration as the factory filter. The key is matching the thread size and flow capacity — using the wrong filter can cause pressure issues or bypass the filter entirely under load.

Key Takeaways

  • The factory filter for a 2013 F-150 5.0L is the Motorcraft FL-820S, which costs between $8 and $15 depending on where you buy it.
  • Aftermarket filters like Fram PH8A, Bosch 3330, and Wix 51515 are direct replacements with the same thread size and flow rating.
  • The filter threads onto the engine block below the intake manifold and is accessible without removing other parts.
  • Always check the filter canister for the correct thread size (3/4-16 UNF) before purchase to avoid cross-threading or leaks.

Where the filter is located and how to access it

On the 2013 F-150 5.0L, the oil filter sits on the driver's side of the engine, mounted vertically below the intake manifold. To reach it, you do not need to remove the wheel well or any major components — it is one of the more accessible filter locations on this truck. You will need to get underneath the engine or use a jack and jack stands to create enough clearance to work comfortably.

The filter head is angled slightly, so a standard oil filter wrench works well. A 3-inch or adjustable filter wrench will grip the canister without slipping. If you use a strap wrench instead, wrap it around the middle of the filter to avoid crushing the thin metal. Once you loosen the filter by hand after breaking it free with the wrench, you can unscrew it by hand — it should come off cleanly without spilling oil if you drain the pan first.

Checking your owner's manual for the exact filter specification

Your 2013 F-150 owner's manual lists the oil filter specification in the maintenance section, usually under "Recommended Fluids and Capacities" or "Maintenance Schedule." The manual will confirm the Motorcraft FL-820S as the factory filter and may also list acceptable substitutes. Ford's service bulletins sometimes note alternative filters that meet the same performance standards, which can help you find options if one brand is out of stock.

The manual also specifies the oil capacity (typically 6 quarts with a filter change for the 5.0L) and the recommended oil viscosity for your climate. Checking the manual before you buy a filter ensures you get the right part and avoid confusion at the parts counter. If you no longer have the physical manual, you can read a PDF version from Ford's owner portal or search for it on automotive documentation sites.

Comparing factory and aftermarket filter options

The Motorcraft FL-820S is the original equipment filter and carries Ford's full warranty coverage if something goes wrong during an oil change. It is also the filter that was installed at the factory, so it has been tested in thousands of 2013 F-150s. The trade-off is cost — Motorcraft filters typically run $10 to $15, which is slightly higher than some aftermarket brands.

Aftermarket filters from Fram, Bosch, Wix, and ACDelco offer the same thread size and bypass valve rating at a lower price point, usually $6 to $12. These filters meet or exceed Ford's OEM specifications and carry their own warranties. The main difference is the media material and bypass valve design — some aftermarket filters have a higher micron rating (finer filtration) or a different bypass pressure, but all the options listed above are engineered to work safely in your 5.0L engine. If you change your oil on schedule, either choice will protect your engine.

What to do if you install the wrong filter

If you accidentally install a filter with the wrong thread size, you will notice it when ready — the filter will not thread on smoothly, or it will cross-thread and jam. Stop and remove it at once. Do not force it, because you can damage the filter head threads on the engine block, which is an expensive repair. Unscrew it slowly by hand, and if it is truly stuck, use a filter wrench to back it out gently.

If you install a filter with the wrong bypass valve rating, the engine will not show symptoms right away, but the filter may bypass prematurely under cold starts or high-load driving. This means unfiltered oil circulates through the engine, which accelerates wear over time. The best safeguard is to double-check the part number on the canister before you thread it on — compare it to the Motorcraft FL-820S or one of the verified aftermarket replacements listed above.

Oil filter change intervals and maintenance schedule

Ford recommends changing the oil and filter every 10,000 miles or 12 months for the 2013 F-150 5.0L, whichever comes first. If you drive in severe conditions — towing, idling in traffic, or dusty environments — Ford suggests shortening the interval to 5,000 miles. Your owner's manual has a detailed maintenance schedule that breaks down severe versus normal driving, so check that section to see which interval applies to your truck.

Changing the filter every time you change the oil is the standard practice and the safest approach. Some people stretch intervals or skip filter changes, but the filter is inexpensive compared to engine damage. A clogged filter forces the bypass valve open, which sends unfiltered oil through the engine and accelerates sludge buildup. Sticking to the schedule keeps your engine clean and protects your warranty.

Frequently Asked Questions

Can I use a different thread size filter if it fits the hole?

No. The 2013 F-150 5.0L uses a 3/4-16 UNF thread, and using a different size will either cross-thread or leak. Even if a filter physically threads on, the wrong size will not seal properly and oil will seep out. Always match the thread size exactly — it is printed on the filter canister.

How much oil comes out when I remove the old filter?

Expect about 1 to 1.5 quarts of oil to drain from the filter and the filter head cavity when you unscrew the old filter. This is why you should drain the pan first and have a drain pan ready under the filter head. Tilt the filter as you unscrew it to direct the oil into the pan and minimize spillage.

Do I need to pre-fill the new filter with oil before installing it?

It is not required, but many technicians fill the filter halfway with fresh oil before threading it on. This reduces the time the engine runs without full oil pressure after a cold start. If you do pre-fill, wipe the rubber gasket with a clean rag first so oil does not prevent a proper seal.

What if the filter wrench slips and I cannot get the old filter off?

Use a strap wrench instead of a band wrench — wrap it around the middle of the filter and pull steadily. If the filter is truly stuck, try tightening a hose clamp around the middle and using that as a grip point. As a last resort, carefully puncture the filter with a screwdriver and use the hole as a lever to turn it, but this is messy and should only be done if the filter is already damaged.

Is synthetic oil compatible with the Motorcraft FL-820S filter?

Yes. The Motorcraft FL-820S and all the aftermarket replacements listed work with conventional, synthetic blend, and full synthetic oils. The filter media and bypass valve are rated for all oil types. The filter change interval may differ depending on the oil you use — synthetic oils often allow longer intervals — so check your owner's manual for the interval that matches your oil choice.