The 1968 Dodge Charger: Engine and Performance Basics

The 1968 Dodge Charger came with one of three engines: a 225-cubic-inch slant-six producing 145 horsepower, a 318-cubic-inch V8 with 230 horsepower, or the high-performance 440-cubic-inch Magnum V8 rated at 375 horsepower. The engine you have determines how the car behaves under load, how much fuel it burns, and what maintenance intervals matter most. The slant-six is durable and economical but underpowered for a car that weighs 3,600 pounds; the 318 offers a middle ground; the 440 is what made the Charger famous, but it demands regular oil changes and cooling system attention.

All three engines use a carburetor rather than fuel injection—a single four-barrel carb on the 440, simpler setups on the smaller engines. Carburetors are mechanical devices that mix air and fuel by vacuum and mechanical linkage. They require periodic cleaning and adjustment, especially after sitting for months. If your Charger has been stored, the carburetor jets are likely varnished, and the fuel in the tank has oxidized. This is the first thing to address before trying to start the car.

Key Takeaways

  • The 1968 Charger's carburetor needs cleaning and fuel system flushing if the car has sat idle, because old gasoline leaves varnish that blocks fuel flow and clogs jets.
  • The cooling system uses a mechanical fan and a radiator that can corrode internally; flushing it with fresh coolant every few years prevents overheating and head gasket failure.
  • The points-and-condenser ignition system requires regular inspection and replacement because worn points cause hard starting, rough idle, and stalling.
  • The original drum brakes on the rear and front discs (or drums on early models) need regular inspection for wear and fluid leaks, because brake fade increases stopping distance.
  • Suspension bushings, ball joints, and tie-rod ends wear out and cause steering play and uneven tire wear; replacing them restores handling and safety.

Carburetor and Fuel System: Why Old Fuel Matters

Gasoline oxidizes over time, especially in a warm garage or shed. After six months or more, the fuel turns brown or amber and deposits varnish inside the carburetor, fuel lines, and tank. This varnish blocks the small passages in the carburetor jets, preventing fuel from flowing to the engine. The result is a car that cranks but will not start, or starts briefly and dies.

Before you assume the engine is broken, drain the old fuel from the tank and replace it with fresh gasoline. If the car still will not start or runs rough, the carburetor needs to come off and be soaked in carburetor cleaner or sent to a shop for ultrasonic cleaning. Do not try to poke the jets with a wire—you will enlarge them and ruin the carburetor's calibration. A proper cleaning takes a few hours and costs $75 to $150 at a shop, but it is far cheaper than replacing the carburetor.

Check the fuel lines for cracks or leaks. Original rubber hose hardens and becomes brittle after 50 years. A cracked fuel line can leak gasoline onto the engine, creating a fire hazard. Replace any hose that shows cracks, discoloration, or a hard, inflexible feel. Use fuel-rated hose, not generic rubber tubing.

Ignition System: Points, Condenser, and Spark Plugs

The 1968 Charger uses a points-and-condenser ignition system, not electronic ignition. Inside the distributor, a mechanical arm called the rotor opens and closes a set of contact points as the engine turns. When the points open, they break the electrical circuit and create a spark at the spark plugs. The condenser is a small capacitor that prevents arcing across the points and extends their life.

Points wear out. The contact surfaces pit and corrode, causing the gap between them to change. When the gap is wrong, the spark timing shifts, and the engine runs rough, starts hard, or stalls. Worn points also cause the engine to lose power at highway speeds. Replacing the points and condenser is a job you can do yourself in 20 minutes with basic tools: remove the distributor cap, unscrew the old points, install new ones, and set the gap with a feeler gauge to the specification in your owner's manual (usually 0.016 to 0.020 inch).

Spark plugs should be replaced every 10,000 miles on a points system, or every 5,000 miles if the car sits for long periods between drives. Old plugs have wider gaps and require higher voltage to fire, which stresses the ignition coil and makes cold starts harder. Use the plug type specified in your manual—usually a Champion or AC plug with a heat range suited to your engine.

Cooling System: Radiator, Hoses, and Thermostat

The 1968 Charger's cooling system is straightforward: a water pump driven by a belt, a radiator with a mechanical fan, and a thermostat that opens when coolant reaches about 180 degrees Fahrenheit. The radiator is brass or aluminum with copper tubes, and the inside can corrode or clog with rust and mineral deposits. If you have never flushed the cooling system, the radiator is likely restricted, and the engine will overheat under load or in traffic.

Flush the radiator by draining the old coolant, filling the system with fresh water, running the engine until it reaches operating temperature, draining again, and repeating until the water runs clear. Then refill with a 50/50 mix of antifreeze and distilled water. This removes rust, scale, and old corrosion inhibitors that have broken down. A proper flush takes an hour and costs $50 to $100 at a shop, or you can do it yourself if you are comfortable working with hot coolant.

Check the radiator hoses for cracks, leaks, or soft spots. Original hoses are likely hardened and brittle. Replace any hose that feels hard or shows visible cracks. Also inspect the water pump for leaks around the shaft seal—a weeping pump will eventually fail and leave you stranded. The fan belt should be tight enough that you can deflect it about half an inch with thumb pressure at the midpoint; a loose belt will slip and fail to cool the engine.

Brake System: Drums, Discs, and Fluid

The 1968 Charger came with front disc brakes and rear drum brakes, or all drums on early models. Disc brakes are more effective at stopping and dissipating heat, but they require regular inspection of the brake pads and rotors. Drum brakes are simpler but prone to fade if the brake fluid overheats or if the drums become glazed.

Brake fluid absorbs moisture from the air over time. Old, contaminated fluid has a lower boiling point and can cause the brakes to fade or fail when you brake hard or descend a long hill. Flush the brake system every two years: open the bleeder valves at each wheel, pump fresh fluid through until it runs clear, and close the valves. This removes old fluid and air bubbles that reduce braking power. If you have never done this, a shop can do it in 30 to 45 minutes for $75 to $150.

Inspect the brake pads (front) and linings (rear) for thickness. Pads should be at least 3/32 inch thick; linings should be 1/8 inch or more. Worn brakes increase stopping distance and can damage the rotors or drums. Also check for leaks at the wheel cylinders (rear) and calipers (front). A slow leak will eventually leave you with no brakes.

Suspension and Steering: Bushings, Ball Joints, and Tie-Rods

The 1968 Charger's suspension uses upper and lower control arms with ball joints, coil springs, and a solid rear axle with leaf springs. All of these components have rubber bushings that absorb vibration and allow movement. After 50 years, these bushings are cracked, hardened, or missing entirely. When bushings wear out, the suspension becomes loose, the steering feels vague, and the tires wear unevenly.

Common wear points are the lower ball joints, which support the weight of the front end and move up and down as the suspension compresses. A worn ball joint will rattle when you drive over bumps and will eventually fail, causing the wheel to collapse inward. Check for play by grasping the tire at the 3 and 9 o'clock positions and trying to move it up and down. If there is more than a quarter inch of movement, the ball joint needs replacement.

The tie-rod ends connect the steering box to the wheels and allow the wheels to turn. Worn tie-rod ends cause the steering wheel to feel loose and cause the front end to wander. Check them by grasping the tie-rod and trying to move it up and down; any movement means replacement is needed. Replacing ball joints and tie-rod ends is a job for a shop with a lift and alignment equipment, because you will need a wheel alignment after the work is done.

Rubber Seals, Gaskets, and Fluid Leaks

After 50 years, every rubber seal and gasket on the engine has hardened and shrunk. The valve cover gaskets, oil pan gasket, and transmission pan gasket all leak. These leaks are not catastrophic—a few drops per week is normal—but they indicate that the seals are failing and should be replaced during a major service.

Check the engine oil level every time you drive. If the level drops more than a quart between fill-ups, you have a leak or the engine is burning oil. Burning oil usually means worn piston rings or valve seals, which is expensive to fix. A leak from the pan gasket or valve covers is cheaper to address and should be done to prevent oil from dripping on the driveway and to keep the engine clean.

The transmission also leaks. Check the fluid level with the engine running and the transmission in Park, on level ground. The fluid should be bright red and smell like oil, not burnt. If it is dark brown or smells burnt, the transmission fluid has broken down and should be changed. A transmission fluid change on a 1968 Charger takes about an hour and costs $50 to $100 at a shop.

Frequently Asked Questions

Can I drive a 1968 Charger with the original carburetor?

Yes, if it has been cleaned and properly tuned. The original carburetor is part of the car's character and history. However, if it is severely damaged or you cannot get it to run smoothly, a modern electronic fuel injection system can be retrofitted. This improves reliability and fuel economy but costs $1,500 to $3,000 and changes the engine's appearance.

What should I do if the engine overheats?

Stop driving when ready and let the engine cool. Do not remove the radiator cap while the engine is hot—you can be burned by steam. Once cool, check the coolant level and top it off. If the engine overheats again, the radiator may be clogged, the thermostat may be stuck, or the water pump may be failing. Have a shop diagnose the problem before driving the car again.

How often should I change the oil in a 1968 Charger?

Every 3,000 miles or every three months, whichever comes first. Older engines with loose tolerances and points ignition systems benefit from frequent oil changes. Use a high-quality mineral oil rated for older engines, typically 10W-30 or 10W-40. Synthetic oil can be used but is not necessary and costs more.

What is the best way to store a 1968 Charger for the winter?

Fill the fuel tank to prevent condensation inside, add fuel stabilizer to prevent varnish, disconnect the battery to prevent slow discharge, and cover the car with a breathable tarp. Do not use a plastic tarp, which traps moisture and promotes rust. If possible, park in a dry garage or shed. Start the engine and drive it for 15 minutes every month to keep the battery charged and the oil circulating.

Do I need to replace the original wiring harness?

Not when ready, but original cloth-covered wiring becomes brittle and the insulation cracks, exposing bare copper and creating a fire hazard. If you are restoring the car or planning to drive it regularly, replacing the wiring harness is a good investment. A quality reproduction harness costs $300 to $600 and takes a shop 8 to 12 hours to install. You can also repair sections of the original harness by wrapping them with electrical tape as a temporary fix.