What a Subaru remote start key fob does
A Subaru remote start key fob lets you start your engine from outside the vehicle using a button on your key. When you press the remote start button, the fob sends a signal to your car's receiver module, which cranks the engine and runs it for a set time—usually 10 to 15 minutes—before shutting off automatically. This feature works whether you're in your driveway, at a store, or anywhere within range of the receiver (typically 300 to 500 feet, depending on obstacles).
Remote start is standard on many newer Subaru models, though availability and range vary by year and trim level. Some Subaru vehicles require the key fob to be within a certain distance or line of sight to work properly. The engine will not start if your doors are locked or if the car detects a safety issue, such as low fuel or an open hood.
Key Takeaways
- Subaru remote start activates through a dedicated button on your key fob and runs the engine for 10 to 15 minutes before shutting down automatically.
- Remote start does not work if your doors are locked, fuel is critically low, or the car detects an open hood or other safety condition.
- A dead key fob battery is the most common reason remote start stops working, and replacing the battery usually costs under $10.
- If your fob battery is good but remote start still does not work, the receiver module in your car may need reprogramming or replacement by a Subaru dealer.
- You can test whether your fob is the problem by trying the lock and unlock buttons—if those work, the issue is likely the remote start circuit specifically.
How to identify the remote start button on your fob
The remote start button on a Subaru key fob is usually marked with a car icon or an arrow pointing away from a vehicle. On most models, it is a separate button from the lock and unlock buttons, often positioned at the top or side of the fob. Some Subaru fobs require you to hold the button for 2 to 3 seconds rather than press it once; check your owner's manual for your specific model year.
If you are unsure which button starts the engine, your owner's manual will show the exact layout for your fob. You can also contact a Subaru dealer with your vehicle identification number (VIN) and model year, and they can confirm which button to use.
Why your remote start key fob might not be working
The most common reason remote start fails is a dead or dying battery inside the fob itself. Subaru key fobs typically use a CR2032 or similar coin-cell battery that lasts 3 to 4 years with normal use. If the lock and unlock buttons still work but remote start does not, the battery may still have enough charge for those functions but not enough for the higher-power remote start circuit.
A second common cause is that the receiver module in your car has lost its pairing with the fob. This can happen after a battery disconnect, a dead car battery, or a software glitch. The module may need to be reprogrammed or, in rare cases, replaced. A third possibility is that a safety interlock is preventing the start—for example, the car will not remote-start if the hood is open, the doors are unlocked, or the fuel tank is nearly empty.
Less often, the remote start button itself may be worn out or damaged, especially if the fob has been dropped or exposed to moisture. Water damage inside the fob can corrode the circuit board and disable specific buttons while leaving others functional.
How to replace your key fob battery
Replacing a Subaru key fob battery is straightforward and takes about five minutes. First, locate the small slot or seam on the edge of your fob and use a flat tool—a coin, flathead screwdriver, or plastic pry tool—to gently separate the two halves. Do not force it; the fob is designed to open with light pressure.
Once open, note the orientation of the old battery (the + side usually faces up or toward you). Remove the old battery and replace it with a new CR2032 or the equivalent battery type for your fob. You can find the correct battery type printed on the old battery or in your owner's manual. Close the fob halves back together until they click, and test the remote start button.
If remote start still does not work after a fresh battery, the issue is likely not the battery itself. Move on to testing the receiver module or contacting a dealer.
Reprogramming your fob if remote start stops working
If your battery is fresh but remote start still does not respond, the receiver module in your car may have lost its pairing with the fob. Some Subaru models allow you to reprogram the fob yourself using a sequence of key turns and button presses, though the exact steps vary by year and model. Your owner's manual will include the reprogramming procedure if your vehicle supports it.
Many newer Subaru models do not support owner reprogramming and require a dealer to reprogram the receiver module. A Subaru dealer can reprogram your fob in about 15 to 30 minutes, usually for a fee between $50 and $150 depending on the location and model. If reprogramming does not restore remote start, the receiver module itself may be faulty and need replacement, which is a more expensive repair that only a dealer can perform.
When to contact a Subaru dealer
Contact a Subaru dealer if you have replaced the battery and remote start still does not work, or if you are unsure whether your vehicle even has remote start capability. Bring your key fob and your vehicle identification number (VIN). The dealer can check whether your specific model and year came with remote start, confirm that the receiver module is working, and reprogram or replace components as needed.
If your fob is physically damaged—cracked, water-logged, or with buttons that do not respond at all—the dealer can order a replacement fob and program it to your vehicle. A new OEM Subaru key fob typically costs between $200 and $400, though some dealers offer refurbished fobs at a lower price. Ask about warranty coverage on the fob itself; some Subaru warranties cover key fob defects for a limited time.
Testing your fob before you assume it is broken
Before you spend money on repairs, test whether the problem is the fob or the car. Stand near your Subaru and press the lock button on your fob. If the doors lock, the fob is transmitting a signal. Now press unlock. If the doors unlock, the fob battery has enough power for basic functions. Finally, press the remote start button and listen for the engine to crank.
If lock and unlock work but remote start does not, the fob battery may be low (replace it first) or the remote start circuit in the fob may be faulty. If none of the buttons work—lock, unlock, or remote start—the battery is almost certainly dead. If the battery is new and still nothing works, the fob itself may be damaged or the receiver module in the car may not be responding to any fob signals.
Frequently Asked Questions
Can I remote start my Subaru if the doors are locked?
No. Subaru remote start will not function if the doors are locked as a safety feature. You must unlock the doors first using your fob or key, then press remote start. This prevents someone from starting your car without being able to enter it.
How long does the engine run after I press remote start?
The engine typically runs for 10 to 15 minutes before shutting off automatically. The exact time depends on your model year and trim level. You can press the remote start button again to extend the run time for another cycle, up to a maximum set by Subaru.
What does it mean if remote start works sometimes but not always?
Intermittent remote start usually points to a weak key fob battery. Replace the battery first. If the problem persists, the receiver module may be losing its pairing intermittently, which requires dealer reprogramming. Distance and obstacles can also affect range; try remote start from closer to the vehicle.
Is remote start the same as keyless ignition?
No. Remote start cranks the engine from outside the car using your fob. Keyless ignition (push-button start) lets you start the engine from inside the car without inserting a physical key. Many Subarus have both features, but they use different systems.
Can I use a generic key fob for remote start, or does it have to be a Subaru fob?
You must use a Subaru key fob programmed to your specific vehicle. Aftermarket or generic fobs may work for lock and unlock on some models, but remote start requires the correct fob paired to your car's receiver module. A Subaru dealer can program an OEM fob to your vehicle.