Subaru key fob batteries typically last three to four years and cost $5 to $15 to replace

Your Subaru key fob runs on a coin-cell battery, usually a CR2032 or CR2025, that you can swap yourself in under a minute. The battery dies gradually — you'll notice the fob working only when held close to the car, then stopping altogether. Replacement batteries are sold at drugstores, supermarkets, and auto parts retailers, and the swap requires no tools beyond your fingernail or a coin.

If your fob stops working suddenly rather than gradually, the problem may not be the battery. Water damage, a broken button, or a damaged circuit board can also kill a fob. But battery replacement is the first thing to try, costs almost nothing, and solves the problem in most cases.

Key Takeaways

  • Subaru key fobs use CR2032 or CR2025 coin-cell batteries that you can buy at any drugstore or supermarket for $3 to $8.
  • You open the fob by sliding or prying the two halves apart with a coin or fingernail — no screwdriver needed.
  • The battery sits in a metal holder and slides out sideways; note which side faces up before you remove it.
  • If the fob still doesn't work after battery replacement, water damage or a broken button is likely the cause.

Finding the right battery for your Subaru fob

Most Subaru key fobs from the past 15 years use a CR2032 battery, a flat silver coin about the size of a dime. Some older models use a CR2025, which is slightly thinner. Check your owner's manual or look at the battery compartment inside the fob itself — the battery type is printed on the metal holder.

You can also call a Subaru dealer with your vehicle's year and model, and they'll tell you which battery your fob needs. Once you know the type, buy a pack at a pharmacy, grocery store, or auto parts chain. Avoid the cheapest generic brands; Energizer, Duracell, and Panasonic batteries last longer and cost only slightly more.

Opening your key fob safely

Subaru fobs have two halves held together by a seam. Locate the thin gap between the two plastic shells — it usually runs along one edge. Slide a coin (a dime or penny works well) or your fingernail into the gap and gently twist to pry the halves apart. Do not force it; if it won't budge, try a different spot along the seam.

Once the fob cracks open, you'll see the battery sitting in a metal holder, usually in the center. The two halves are connected by a small rubber gasket or ribbon; don't pull them completely apart or you risk damaging this connector. Set the fob down with both halves still loosely attached so you can work on the battery without losing small parts.

Removing and replacing the battery

The battery sits in a metal holder with a small lip or edge on one side. Slide the battery sideways out of the holder — it should move easily. Before you install the new battery, note which side was facing up on the old one. The positive side (marked with a + symbol) should face up in most Subaru fobs, but check the holder itself for any markings.

Slide the new battery into the holder with the correct side facing up. It should fit snugly and sit flush with the metal holder. Do not force it; if it doesn't slide in smoothly, you may have the polarity reversed. Flip it and try again.

Closing the fob and testing

Once the battery is in place, press the two halves of the fob back together. You should hear or feel a small click as they snap into place. The rubber gasket will reseal, and the fob should be water-resistant again.

Test the fob by standing near your Subaru and pressing each button. The lock and unlock buttons should respond when ready, and the lights on the dashboard should flash. If nothing happens, open the fob again and check that the battery is seated correctly and facing the right direction. If the fob still doesn't work after a second attempt, the problem is likely not the battery.

What to do if battery replacement doesn't fix the fob

If the fob worked fine before the battery died and still doesn't work after you've installed a fresh battery, water damage is the most common cause. Subaru fobs are water-resistant but not waterproof; exposure to rain, sweat, or a spill can corrode the circuit board inside. You may see white or green corrosion on the metal contacts or circuit board when you open the fob.

A broken button is the second most common issue. If one button works but others don't, the rubber button pad or the plastic switch underneath may be damaged. Subaru dealers can replace the internal components or the entire fob. A replacement fob from a dealer typically costs $200 to $400, though you can sometimes find aftermarket fobs for less. If your car is still under warranty, ask the dealer whether battery replacement is covered.

Preventing future battery problems

Coin-cell batteries in key fobs last longer if you avoid exposing the fob to extreme heat, moisture, or pressure. Don't leave it in direct sunlight on a hot dashboard, and don't sit on it or drop it. If your fob gets wet, open it as soon as possible and let the battery holder and circuit board air-dry for a few hours before closing it again.

Keep a spare fob in a dry place so you have a backup if one fails. Many Subaru owners program a second fob when they buy the car and store it at home. If you don't have a spare, ask a dealer or a locksmith about programming a new one — the cost varies by location and model year.

Frequently Asked Questions

How do I know if my Subaru fob battery is dead?

A dying battery shows up as a shrinking range first — you have to hold the fob closer to the car for it to work. Eventually the buttons stop responding altogether, even when pressed hard or held down. If the fob worked fine yesterday and today it doesn't work at all, the battery is usually the culprit.

Can I use any CR2032 battery in my Subaru fob?

Yes, any CR2032 or CR2025 battery will fit and work, but quality matters. Cheap generic batteries may last only a year or two, while name brands like Energizer or Duracell typically last three to four years. The price difference is small, so a better battery is worth it.

What if I lost my key fob and need a replacement?

A Subaru dealer can order a new fob and program it to your car. Bring your vehicle identification number (VIN) and proof of ownership. Aftermarket fobs sold online are cheaper but may not work with all Subaru models, and programming them can be tricky. A locksmith who works with cars can also order and program a fob for you, often at a lower cost than a dealer.

Is it safe to open my key fob myself?

Yes, opening a Subaru fob to replace the battery is safe and requires no special tools. The only risk is damaging the rubber gasket if you pry too hard, which would make the fob less water-resistant. Take your time, use a coin or soft object, and avoid forcing the halves apart.

Why does my fob work sometimes but not other times?

Intermittent fob problems usually mean the battery is dying and the connection is loose. Try replacing the battery first. If the problem persists, water may have corroded the contacts inside, or a button may be sticking. Open the fob and look for corrosion or debris on the circuit board or button pad.