Your Subaru key fob will stop working when its battery runs out, but you can still unlock and start your car

When your Subaru access key shows a low battery warning or stops responding, the fob's coin-cell battery has drained. This does not lock you out of your vehicle. You can still unlock the driver's door using the physical key blade hidden inside the fob, and you can still start the engine once inside because the car recognizes your key's chip through proximity alone—the battery powers only the wireless transmitter, not the chip itself.

The warning appears on your dashboard or through the Subaru Starlink app (if your model has it) when the battery voltage drops below a usable threshold. Most Subaru fobs use a CR2032 or CR2025 coin-cell battery, which costs between $3 and $8 and lasts three to four years depending on how often you use the fob. Replacing it takes about five minutes and requires no tools beyond a coin or flathead screwdriver.

Key Takeaways

  • A dead key fob battery only disables the wireless lock and unlock buttons; you can still open your car with the physical key blade and start it normally.
  • Most Subaru fobs use a CR2032 or CR2025 battery that you can replace yourself by prying open the fob case with a coin.
  • Replace the battery as soon as you see the low battery warning to avoid being stranded without a working remote.
  • If your fob stops working after battery replacement, the issue may be a worn contact or a deeper electrical problem, not the battery itself.

How to identify which battery your Subaru fob uses

The battery type is printed on the inside of your fob case. Open the fob by inserting a coin into the slot along the edge and twisting gently until the two halves separate. The battery sits in a small metal holder, and its type—CR2032, CR2025, or occasionally CR2016—is stamped on the battery itself or printed on the inside of the case.

If you cannot find the marking, check your owner's manual or call your Subaru dealer with your vehicle's year, make, and model. Most dealers stock both CR2032 and CR2025 batteries, and either can be ordered online from pharmacies, electronics retailers, or supermarkets. Do not assume all Subaru fobs use the same battery; some older models use different types.

Steps to replace the battery yourself

Gather a coin (a dime or penny works well) and your replacement battery before you start. Locate the slot or seam running along the edge of your fob—it is usually on the side where the two plastic halves meet.

Insert the coin into the slot and twist gently, explore steady pressure without forcing it. The fob case will crack open slightly. Once you see a gap, use your fingernail or the coin edge to pry the two halves apart completely. Set the metal battery holder aside carefully so you do not lose the small spring underneath it.

Remove the old battery and note which side was facing up—the positive side (marked with a +) should face the same direction when you insert the new battery. Place the new battery into the holder with the correct orientation, then reassemble the fob by pressing the two halves together until they click. Test the lock and unlock buttons to confirm the fob works.

When to replace the battery before it fully dies

Subaru's low battery warning gives you a window of time to replace the battery before the fob stops working entirely. If you see the warning on your dashboard or receive a notification through Starlink, replace the battery within the next week or two rather than waiting until the fob fails completely.

Waiting until the fob is completely dead creates unnecessary risk: you might be in a situation where you cannot easily access your car, or you might forget to carry the physical key blade with you. Replacing the battery proactively takes five minutes and costs less than $10, making it one of the easiest preventive steps you can take.

What to do if the fob still does not work after battery replacement

If your fob remains unresponsive after you install a fresh battery, the problem is not the battery itself. The most common cause is corrosion or wear on the metal contacts inside the fob case. These contacts connect the battery to the circuit board, and if they are dirty or damaged, power cannot flow even with a new battery installed.

Open the fob again and inspect the metal contacts—they should be shiny and clean. If they look dull, dark, or corroded, gently rub them with a pencil eraser or a small piece of fine sandpaper (220-grit or higher) to restore the connection. Reassemble the fob and test it. If the fob still does not work, the circuit board itself may be damaged, and you will need a replacement fob from your Subaru dealer.

Dealer replacement versus aftermarket fobs

A new fob from a Subaru dealer typically costs between $150 and $300 depending on your model year and whether it includes additional features like remote start. The dealer will program the fob to your vehicle at the time of purchase. Aftermarket fobs from third-party manufacturers cost $40 to $100 but require programming, which some dealers charge for separately (usually $50 to $100) and some do not.

If you choose an aftermarket fob, confirm before purchase that it is compatible with your specific Subaru model year and that the seller or a local locksmith can program it. Some aftermarket fobs work reliably; others have poor build quality or compatibility issues. Dealer fobs carry a warranty and are may provide to work, but they cost more upfront.

How to avoid draining your fob battery prematurely

Subaru key fob batteries last longest when the fob is stored away from heat, moisture, and direct sunlight. Leaving your fob in a hot car, in a pocket near body heat, or in a damp environment can shorten battery life significantly. Keep your fob in a cool, dry place when you are not using it, and avoid dropping it or exposing it to water.

Excessive button pressing does drain the battery faster, but normal daily use—locking and unlocking your car a few times a day—should not noticeably shorten battery life. If your fob battery dies much sooner than three to four years, the issue may be a faulty circuit board drawing power even when the fob is not in use, which is a reason to have the fob inspected or replaced by your dealer.

Frequently Asked Questions

Can I start my Subaru if the key fob battery is dead?

Yes. Once you unlock the car using the physical key blade, you can insert the fob into the start button slot (or push the start button while holding the fob near it, depending on your model) and the car will start normally. The fob's battery powers only the wireless transmitter, not the security chip that allows the engine to run.

Will my car lock me out if the fob battery dies while I am driving?

No. A dead fob battery does not affect the locks or engine while you are driving. You will lose the ability to lock or unlock the car remotely, but you can still use the physical key blade to open the door once you park.

What is the difference between CR2032 and CR2025 batteries?

CR2032 and CR2025 are both 3-volt coin-cell batteries, but CR2032 is thicker and holds more charge, giving it a longer lifespan. CR2025 is thinner and fits in fobs with tighter battery compartments. Use whichever type your fob is designed for; using the wrong size can prevent the fob case from closing properly or cause poor contact.

Should I replace the battery at a dealer or do it myself?

Replacing the battery yourself is safe and takes five minutes. Dealers will do it for you, but they typically charge a service fee ($20 to $50) on top of the battery cost, making it more expensive than buying a battery and replacing it at home. Self-replacement is the better choice unless you are uncomfortable opening the fob.

Can I use a regular alkaline battery instead of a coin-cell battery?

No. Alkaline batteries are larger and will not fit in the fob's battery compartment. Coin-cell batteries are the only type designed for key fobs. Using the wrong battery can damage the fob or create a safety hazard.