A dead key fob battery is one of the easiest car problems you can fix yourself
Your key fob stops working because the battery inside has run out of power, not because the fob itself is broken. The battery is a small coin-shaped cell—usually a CR2032, CR2025, or similar—that costs between $3 and $8 and lasts three to four years depending on how often you use the fob. You can replace it in about five minutes with nothing but a coin or a small flathead screwdriver. No trip to the dealership, no special tools, no waiting.
Before you assume the battery is dead, press every button on the fob while standing close to your car. If nothing happens—no door unlock, no trunk pop, no lights—the battery is almost certainly the problem. If the buttons work sometimes or only from very close range, the battery is dying. If the buttons work fine but your car doesn't respond, that is a different issue (the car's receiver, not the fob).
Key Takeaways
- Most key fobs use a CR2032, CR2025, or CR2016 coin battery that you can buy at any pharmacy, grocery store, or hardware store for under $10.
- The fob case usually pops open with a coin or flathead screwdriver wedged into a small slot on the edge—no special tools needed.
- Note which side of the battery faces outward before you remove it, because the new battery must go in the same way or the fob will not work.
- After you snap the case back together, test all the buttons before you put the fob away to make sure the battery made contact properly.
Find out what battery your fob uses
The easiest way is to look at your fob's manual, which came with your car or is available on your car manufacturer's website. Search "[your car brand] [your model year] key fob manual" and look for the battery type listed in the specifications section.
If you do not have the manual, you can open the fob and look at the battery itself. The battery type is printed on the flat side—CR2032, CR2025, or CR2016 are the most common. Once you know the type, you can buy a replacement at a pharmacy, grocery store, hardware store, or online. Most stores stock these batteries in the watch and battery section near the checkout.
Do not buy a bulk pack unless you have multiple fobs. A single battery is cheaper and you will use it within a few years anyway.
Open the fob case without breaking the plastic
Look at the edge of your fob for a small slot or seam. This is usually on the side where the two halves of the plastic case meet. Some fobs have a slot that runs along the entire edge; others have just a small notch on one side. This slot is where you wedge your tool to pry the case open.
Use a coin (a dime or penny works well) or a small flathead screwdriver. Insert the edge into the slot and twist gently—do not force it. The case should pop apart with light pressure. If it does not budge after a gentle twist, try a different spot along the seam. Some fobs have multiple weak points, and you may need to work your way around the edge.
Once the case cracks open, you can usually pull the two halves apart by hand. Be careful not to lose any small springs or contacts that might fall out. If your fob has a metal or plastic insert holding the battery, note how it sits before you remove it.
Remove the old battery and install the new one
Look at the battery sitting in the fob. The side facing up is usually marked with a + or – symbol, or it may just be a flat metal surface. Before you touch it, take a mental note of which side is facing outward. This matters: if you put the new battery in backwards, the fob will not work.
Gently pry the old battery out with your fingernail or the edge of a coin. Do not use a sharp tool that could scratch the contacts inside the fob. Once the battery is out, clean the metal contacts with a dry cloth or a pencil eraser if they look dirty or corroded. Dirt on the contacts is a common reason a new battery does not work.
Slide the new battery into the same position, with the same side facing outward as the old one. Press it down gently until it sits flat. You should hear or feel a small click as it settles into place.
Close the case and test the fob
Align the two halves of the case and press them together firmly until they snap. You may hear a click or feel a slight resistance as the case locks. Do not force it—if it does not snap easily, the battery may not be sitting flat, or a small part may be in the way.
Stand near your car and press each button on the fob: lock, unlock, trunk, panic, or any other buttons your fob has. The car should respond to each one. If nothing happens, open the fob again and check that the battery is sitting flat and facing the right direction. If the battery is in correctly but the fob still does not work, the fob itself may be damaged, and you will need a replacement from your car manufacturer or a locksmith.
When to replace the fob instead of just the battery
If you have replaced the battery and tested it, and the fob still does not work, the problem is inside the fob itself. Water damage, a cracked circuit board, or worn-out buttons can all prevent a fob from working even with a fresh battery. In this case, you have two options: buy a replacement fob from your car manufacturer (usually $100 to $300 depending on the car), or buy an aftermarket fob from a locksmith or online retailer (usually $30 to $100).
Aftermarket fobs are cheaper but may not have all the features of the original—some do not have remote start, for example. Before you buy a replacement, check your car's manual to see what features your fob should have, and make sure the replacement fob supports them. Many aftermarket fobs can be programmed by the owner, but some require a trip to the dealership or a locksmith to pair with your car.
How to know if your fob battery is about to die
A dying battery does not always fail all at once. You might notice that the fob only works from very close to your car, or that you have to press the button several times before the car responds. You might also notice that the fob works sometimes and not other times, especially in cold weather (cold slows down battery chemistry). These are all signs that the battery is running low and will fail completely within days or weeks.
If you notice these signs, replace the battery now rather than waiting for the fob to stop working completely. A fresh battery costs less than $10 and takes five minutes, so there is no reason to wait until you are locked out of your car in a parking lot.
Frequently Asked Questions
Can I use a different battery type if I cannot find the exact one?
No. CR2032, CR2025, and CR2016 are different sizes and voltages, and using the wrong one can damage the fob or cause it to malfunction. Buy the exact type your fob uses. If your store does not have it, order it online—it will arrive within a day or two.
What if the fob case will not open?
Try a different spot along the seam. Some fobs have a slot on only one side, and you may be trying to open it at the wrong place. If you still cannot open it, a locksmith can open it for you, usually for $10 to $20, and they can replace the battery at the same time.
Do I need to reprogram the fob after I replace the battery?
No. Replacing the battery does not erase the fob's programming. As soon as the new battery makes contact, the fob should work exactly as it did before. If it does not work after you install the new battery, the fob is damaged, not unprogrammed.
How long does a key fob battery last?
Most key fob batteries last three to four years with normal use. Heavy use—pressing the buttons many times per day—can shorten the life to two years. Light use can extend it to five years. Cold weather also drains batteries faster, so you might notice your fob dying sooner in winter.
Can I replace the battery in a smart key or push-button fob?
Yes, the process is the same. Smart keys and push-button fobs use the same coin batteries as regular fobs. Open the case the same way, replace the battery, and test it. If your smart key has a physical key blade inside, be careful not to lose it when you open the case.