You can replace a Subaru key fob battery yourself in about five minutes with a coin and a replacement battery
Subaru key fobs use a coin-cell battery that dies every few years. The replacement is straightforward: you pry open the fob with a coin, remove the old battery, and snap in a new one. The whole job costs between $3 and $8 for the battery itself. You do not need to visit a dealer or a locksmith unless the fob stops working after you replace the battery, which usually means the fob itself has failed.
Most Subaru fobs use a CR2032 battery, though some older models use CR2025. If you are not sure which one your fob needs, you can open it first and check the number printed on the battery before you buy a replacement.
Key Takeaways
- Subaru key fobs typically use a CR2032 coin-cell battery that you can buy at any pharmacy, grocery store, or hardware store for $3 to $8.
- You open the fob by inserting a coin into the slot on the edge and twisting gently until the two halves separate.
- The battery sits in a metal holder and slides out; note which side faces up before you remove it so you can install the new one the same way.
- After you insert the new battery, press the fob halves together until they click, then test the buttons to confirm it works.
- If the fob still does not work after you replace the battery, the fob itself may be damaged and you will need a replacement from a dealer or locksmith.
What battery your Subaru key fob uses
The vast majority of Subaru key fobs made in the last 15 years use a CR2032 battery. This is a standard coin-cell battery 20 millimeters across and 3.2 millimeters thick. You can find CR2032 batteries at any pharmacy, supermarket, or hardware store, usually in the watch or electronics section. A single battery costs between $3 and $8 depending on the brand and where you buy it.
Some older Subaru models use a CR2025 battery instead, which is the same diameter but slightly thinner. If you open your fob and see a different number printed on the battery, write that number down and search for it before you buy. Buying the wrong size will not damage anything, but the fob will not work until you swap it for the correct one.
How to open your key fob
Look at the edge of your Subaru key fob for a small slot or seam. Insert a coin (a penny or dime works fine) into that slot. Twist the coin gently, as if you were opening a battery compartment on a flashlight. The two halves of the fob will separate after a quarter turn or so. Do not force it; if it does not move, you may have the coin in the wrong spot.
Once the fob is open, you will see the battery sitting in a metal holder. The battery is round and silver, about the size of a dime. Note which side is facing up — the positive side (marked with a + symbol) usually faces up, but check before you remove it so you can put the new battery in the same way.
Removing and replacing the battery
Slide the old battery out of its metal holder. It should come out easily; if it is stuck, use your fingernail or a plastic tool to gently pry it up. Do not use a metal tool that could scratch the circuit board inside the fob.
Take your new CR2032 battery and slide it into the holder with the positive side facing the same direction as the old battery was facing. The battery should sit flat and flush in the holder. If it does not fit smoothly, double-check that you have the right battery size.
Closing the fob and testing it
Press the two halves of the fob together. You should hear or feel a click as they snap back into place. If they do not click, the battery may not be seated correctly; open the fob again and check that the battery is sitting flat in its holder.
Once the fob is closed, test the lock and unlock buttons. Point the fob at your Subaru from a few feet away and press each button. You should see the lights on your car flash or hear the locks engage. If the buttons work, the battery replacement is complete. If nothing happens, try opening the fob again and reseating the battery to make sure it is making good contact with the metal holder.
When to replace the fob itself instead
If you have replaced the battery and the fob still does not work, the fob itself has likely failed. This can happen if the fob was dropped, exposed to water, or straightforward worn out from years of use. A replacement fob from a Subaru dealer typically costs between $150 and $300, depending on your model year and whether the fob has remote start or other advanced features.
You can also buy aftermarket fobs online for $30 to $80, though you will need to have a dealer or locksmith program the new fob to your car. Programming usually costs $50 to $150 and takes 15 to 30 minutes. If you buy a used fob from a salvage yard or online marketplace, confirm that it is the correct part number for your Subaru before you pay, because programming a fob to the wrong model year will not work.
Where to buy replacement batteries
CR2032 batteries are sold everywhere. Pharmacies like CVS and Walgreens stock them in the watch section. Supermarkets like Kroger and Safeway carry them near the pharmacy or in the electronics aisle. Hardware stores like Home Depot and Lowe's have them in the electrical section. Online retailers like Amazon sell them in bulk packs of 4 or 10 if you want to keep spares on hand.
Brand does not matter much for a key fob battery. Duracell, Energizer, and store brands all work the same way. The main difference is price; store brands are usually $1 to $2 cheaper per battery. If you are buying just one, the savings are small, but if you buy a 10-pack, the difference adds up.
Frequently Asked Questions
How often do I need to replace my Subaru key fob battery?
Most key fob batteries last three to four years with normal use. If you use your fob multiple times a day, the battery may wear out faster. You will notice the fob working at shorter distances before it stops working entirely, which is a sign the battery is dying.
Can I damage my key fob by opening it myself?
No, as long as you use a coin to open it and do not force the halves apart. The fob is designed to be opened this way. The only risk is dropping the small battery or the metal holder, so work over a table or counter where you can see everything clearly.
What if my key fob has water damage?
If your fob was submerged or exposed to heavy moisture, replacing the battery alone may not fix it. Water can corrode the circuit board inside. You can try replacing the battery first, but if the fob still does not work, the fob itself needs to be replaced by a dealer or locksmith.
Do I need to reprogram my Subaru after replacing the key fob battery?
No. Replacing the battery does not change any programming. The fob will work exactly as it did before once you install the new battery. Reprogramming is only needed if you buy a new fob or if your car's security system has been reset.
Can I use a different battery size if I cannot find a CR2032?
No. Using a battery that is the wrong size or voltage will not work and could damage the fob's circuit board. Always use the exact battery type printed on the old battery or listed in your owner's manual. If you cannot find the right battery locally, order it online rather than substituting.