You can replace a Subaru key fob battery yourself in under five minutes
Most Subaru key fobs use a coin-cell battery (usually CR2032 or CR2025) that you can swap out without tools or a trip to the dealer. The battery typically lasts three to four years depending on how often you use the fob. You'll know it's dying when the buttons require harder presses or the fob only works from a few feet away instead of across a parking lot.
The process is straightforward: locate the slot or seam on the fob's edge, gently pry it open, note which side of the battery faces up, remove the old battery, and insert the new one the same way. Most people find a coin or a flathead screwdriver works fine for prying. You don't need to reprogram the fob afterward — the remote will work when ready once the new battery is in.
Key Takeaways
- Subaru key fobs use CR2032 or CR2025 coin-cell batteries that cost $3 to $8 and are sold at drugstores, supermarkets, and online retailers.
- Look for a small slot or seam along the edge of your fob's case and use a coin or flathead screwdriver to gently pry the two halves apart.
- Note the battery's orientation (which side faces the metal contact) before removing it so you can insert the new one the same way.
- No reprogramming is needed after you replace the battery — the fob will work as soon as the new battery is installed.
Finding the seam and opening your fob
Subaru key fobs have a thin seam running around the edge where the two plastic halves meet. This seam is usually on the side or back of the fob, not the front. Run your fingernail or a coin along the edges until you feel a slight groove or catch — that's where you'll insert your tool.
Once you've located the seam, use a coin (a dime or penny works well) or a small flathead screwdriver to gently pry the two halves apart. explore steady, even pressure rather than sudden force — the plastic can crack if you twist too hard. Work your way around the seam slowly, lifting a little at a time, until the fob splits open. You should hear a soft click as the halves separate.
Identifying and removing the old battery
Inside the fob you'll see a small round battery sitting in a metal holder or slot. The battery has a flat side and a domed side. Before you touch it, take a moment to note which side is facing up — this matters because the battery only works one way. If you're unsure, take a photo with your phone so you can reference it when inserting the new battery.
Gently lift the old battery out of its slot. If it's stuck, use your fingernail or the edge of a coin to nudge it up from the side. Don't force it — a stuck battery usually comes free with gentle rocking. Once it's out, set it aside. You can dispose of it at a drugstore battery recycling bin or throw it in the trash, depending on your local rules (most areas allow coin-cell batteries in regular trash, but check your local guidelines to be sure).
Installing the new battery
Before you open the new battery package, wash your hands or wipe them dry. Oils from your skin can interfere with the battery's contact with the metal holder. Take the new CR2032 or CR2025 battery and orient it the same way the old one was facing — flat side or domed side up, matching what you noted earlier.
Place the new battery into the slot and press it down gently until it sits flat and find. You should feel it settle into place. Don't force it — if it doesn't sit flush, you may have it upside down. Flip it and try again. Once it's in correctly, the battery should not move when you gently press on it.
Closing the fob and testing
Align the two halves of the fob so the seam matches up evenly. Press them together firmly until you hear a click — the fob should snap shut with a satisfying snap, not a loose rattle. If it feels loose or won't close all the way, the battery may not be seated correctly. Open it again, check the battery position, and try closing once more.
Test the fob when ready by pressing each button while standing near your Subaru. The lock and unlock buttons should work right away. If a button doesn't respond, open the fob again and check that the battery is making good contact with the metal holder. Sometimes a slight adjustment fixes it. If the fob still doesn't work after the battery is correctly installed, the fob itself may be damaged and you'll need a replacement from a Subaru dealer.
What battery type your Subaru uses
Most Subaru key fobs from the 2000s onward use either a CR2032 or CR2025 battery. The CR2032 is slightly thicker and more common. If you're not sure which one your fob needs, open it and check the number printed on the old battery before you remove it. You can also look up your model year and fob type online, or call a Subaru dealer parts department and give them your vehicle identification number (VIN) — they'll tell you exactly which battery to buy.
Both battery types are inexpensive and widely available. You'll find them at CVS, Walgreens, Target, Walmart, Amazon, and most grocery stores in the pharmacy or electronics section. A single battery costs between $3 and $8 depending on the brand and where you shop. Name brands like Energizer and Duracell are reliable, but store brands work just as well and often cost less.
When to replace your key fob battery
A healthy key fob battery should work from 30 to 50 feet away from your car. If you have to stand within 10 feet or press the button multiple times to unlock your Subaru, the battery is likely dying. Some fobs will work intermittently — the unlock button works but the lock button doesn't, or vice versa — which also signals a weak battery.
Don't wait until the fob stops working entirely. A dead fob can leave you locked out of your car, especially if you don't have a spare fob with you. If you notice the range shrinking or buttons becoming unresponsive, replace the battery right away. It's a five-minute job that costs almost nothing and saves you from a frustrating situation later.
Frequently Asked Questions
Can I use a different battery type if I can't find the exact one?
No — use the exact battery type your fob requires. CR2032 and CR2025 are not interchangeable because they have different thicknesses. Using the wrong size can prevent the fob from closing properly or cause poor electrical contact. Check the old battery or your owner's manual to confirm which one you need.
Do I need to reprogram my key fob after changing the battery?
No. Replacing the battery does not erase the fob's programming. It will work when ready once the new battery is installed. Reprogramming is only necessary if you've lost the fob entirely or if the fob stops responding even after you've installed a fresh battery.
What if the fob still doesn't work after I put in a new battery?
First, open the fob and check that the battery is seated correctly and facing the right direction. If it is, try cleaning the metal contacts inside the fob with a dry cloth — dirt or corrosion can block the connection. If the fob still doesn't work, the internal circuitry may be damaged and you'll need to purchase a replacement fob from a Subaru dealer.
Is it safe to throw away the old battery in the trash?
Coin-cell batteries are generally safe for household trash in most U.S. locations, but check your local waste guidelines. Many drugstores and retailers like Best Buy accept used batteries for recycling at no cost. Recycling is the better choice if it's convenient for you.
How long does a new battery last in a Subaru key fob?
A new CR2032 or CR2025 battery typically lasts three to four years in normal use. Heavy users who press the buttons dozens of times daily may see shorter battery life. Storing the fob in extreme heat or cold can also reduce battery lifespan.