You can replace your Subaru fob battery yourself in about two minutes with a coin and a new battery

Your Subaru keyless fob runs on a small coin-cell battery that dies every few years. When the buttons stop responding or respond slowly, the battery is dead. You do not need a dealer or a technician—you can open the fob, swap the old battery for a new one, and be done. The whole job takes longer to read about than to actually do.

The battery type depends on your Subaru model year and fob design, but most use either a CR2032 or CR2025 battery. Both are standard sizes sold at any pharmacy, supermarket, or hardware store for a few dollars. You will also need a flat object—a coin, a flathead screwdriver, or a plastic pry tool—to open the fob case.

Key Takeaways

  • Most Subaru fobs use a CR2032 or CR2025 coin-cell battery that you can buy at any drugstore or supermarket for under five dollars.
  • The fob case opens by inserting a coin or flathead screwdriver into the slot on the edge and twisting gently until the two halves separate.
  • When you remove the old battery, note which side faces up so you install the new one the same way—the positive side usually faces toward you.
  • After closing the fob, test all buttons before you put the old battery in the trash, because a bad battery is the most common reason buttons do not work.

Finding the right battery for your Subaru fob

Check your owner's manual first—it will list the exact battery type for your model. If you do not have the manual, you can also look at the battery compartment inside the fob itself. Once you open it, the battery will be labeled with its type code printed on the metal casing.

CR2032 is the most common battery in newer Subaru fobs. CR2025 is thinner and appears in some older models. Both are the same diameter but different thicknesses, so buying the wrong one means the battery will not sit flush in the compartment. When you buy a replacement, pick up two batteries instead of one—if the first one does not solve the problem, you will have a spare to test.

How to open the fob case safely

Look at the edge of your fob for a small slot or seam. On most Subaru fobs, this slot runs along one edge of the case. Insert a coin (a dime or penny works well) or a flathead screwdriver into the slot, then twist gently. You are not forcing it open—you are using the coin as a lever to separate the two plastic halves.

Turn slowly and let the plastic give way. If you feel hard resistance, stop and try a different spot along the seam. The fob case is plastic and will crack if you force it. Once you feel the halves start to separate, you can usually pull them apart by hand. Set the metal battery contact and any small springs aside on a clean surface so you do not lose them.

Removing the old battery and installing the new one

The old battery sits in a small metal cradle or holder. Note which side faces up—usually the positive side (marked with a + symbol) faces toward you. Gently pry the old battery out with your fingernail or the edge of a coin. Do not use a sharp tool that might scratch the metal contacts inside the fob.

Clean the metal contacts lightly with a dry cloth or your finger if they look corroded or dirty. Corrosion on the contacts is another reason fobs stop working, even with a fresh battery. Slide the new battery into the cradle with the positive side facing the same direction as the old one. The battery should sit flat and snug without wobbling.

Closing the fob and testing the buttons

Align the two halves of the fob case and press them together firmly until you hear or feel a click. The seam should be even all the way around. If one side is higher than the other, the halves are not seated correctly—open it again and check that the battery is sitting flat and that no plastic tabs are bent.

Once the fob is closed, press each button several times. The lock, unlock, and panic buttons should respond when ready. If a button still does not work, open the fob again and check that the battery is installed with the correct side facing up. If the new battery does not fix it, the problem is likely a broken button contact or a failed circuit board inside the fob, which means you will need a replacement fob from a Subaru dealer.

What to do if the fob still does not work after battery replacement

A dead battery fixes about 90 percent of fob problems, but not all. If the buttons still do not respond after you install a fresh battery, the issue is usually inside the fob itself. The plastic contacts under the buttons can wear out or break, or the circuit board can fail.

Test the fob one more time by opening it again and making sure the battery is installed correctly. If you are certain the battery is in the right way and the contacts are clean, the fob needs to be replaced. You can order a replacement fob from a Subaru dealer, a car electronics shop, or an online retailer. Dealers will program it to your car; some aftermarket fobs come pre-programmed, but you should confirm before you buy. The cost ranges depending on your model year and whether you go through a dealer or a third party.

How to keep your fob battery from dying prematurely

Fob batteries last longer when you avoid exposing the fob to extreme heat or moisture. Do not leave it in direct sunlight on a hot dashboard, and do not carry it in a pocket where sweat can reach it. If your fob gets wet, open it and let the battery compartment dry completely before closing it again.

Avoid pressing the buttons repeatedly when the car is off and you are not trying to lock or unlock it. Every button press drains the battery a tiny amount. If you notice the buttons responding slowly—taking a second or two to work—that is a sign the battery is getting weak. Replace it before the buttons stop working entirely, because a weak battery can also cause the car's receiver to miss commands.

Frequently Asked Questions

Can I use a different battery type if I cannot find the exact one?

No. CR2032 and CR2025 look similar but are different thicknesses. Using the wrong one means the battery will not sit flush, the contacts will not touch properly, and the fob will not work. Buy the correct type for your model.

What if I lose a small spring or contact when I open the fob?

Springs and metal contacts are critical. If you lose one, the fob will not work even with a new battery. Take a photo of the inside before you open it, and work over a clean surface where you can see small parts. If you do lose something, contact a Subaru dealer—they can order replacement parts or sell you a new fob.

How long does a new battery last in a Subaru fob?

A coin-cell battery in a keyless fob typically lasts three to four years with normal use. Heavy use—pressing the buttons many times a day—can shorten that to two years. You will notice the buttons responding more slowly before they stop working entirely.

Can I replace the battery in a smart key fob the same way?

Smart key fobs (the larger ones that start the car with a button) often have the same coin-cell battery inside, but the case design is different. Some open with a coin in a slot, others have a small screw, and some have a sliding battery door. Check your owner's manual for the exact method for your model.

Is it safe to throw away the old battery?

Coin-cell batteries contain lithium and should not go in regular trash. Take the old battery to a pharmacy, electronics store, or recycling center that accepts batteries. Many places that sell batteries will also take old ones for free.