You can replace a Subaru key fob battery yourself in under five minutes
Most Subaru key fobs use a CR2032 coin-cell battery that you can buy at any drugstore or supermarket for $3 to $8. The fob itself doesn't need to be taken to a dealer — you open it with a flathead screwdriver or coin, swap the old battery for the new one, and snap it back together. The whole job takes longer to find your screwdriver than to do the work.
The process is the same whether you drive a Crosstrek, Outback, Forester, or WRX. If your fob has stopped locking or unlocking the car, or the buttons feel sluggish, a dead battery is the most common cause and the first thing to check before you assume the fob itself is broken.
Key Takeaways
- Subaru key fobs use a CR2032 battery, which is a standard coin-cell type sold at pharmacies, supermarkets, and online retailers for a few dollars.
- You need only a flathead screwdriver or a coin to pry open the fob — no special tools or technical knowledge required.
- The battery sits in a small metal holder inside the fob; note which side faces up before you remove it so you install the new one the same way.
- After you close the fob, test all buttons (lock, unlock, panic) before you put the fob back in your pocket to confirm the new battery is working.
What battery your Subaru key fob needs
The battery type is CR2032, a 3-volt lithium coin cell that is 20 millimeters in diameter and 3.2 millimeters thick. You will find this exact battery at CVS, Walgreens, Target, Walmart, and most grocery stores with a pharmacy counter. It is also sold online through Amazon and eBay, often in multipacks if you want spares.
The cost is typically $3 to $8 for a single battery, depending on the brand and where you buy it. Name brands like Energizer and Duracell cost slightly more than store brands, but they all perform the same job. If you buy a multipack, you will have extras on hand for future fobs or other devices that use CR2032 batteries — many car remotes, garage door openers, and calculators use the same cell.
How to open your Subaru key fob
Look at the edge of your fob where the two plastic halves meet. You will see a small slot or seam running around the perimeter. Insert a flathead screwdriver or the edge of a coin (a dime or penny works well) into that slot and gently twist or pry. The fob will pop open into two halves — the front cover and the back cover that holds the battery.
Do not force it. If the fob resists, try a different spot along the seam; the opening point is usually where the seam is widest. Once you have opened it once, you will see exactly where to insert the tool the next time. Keep both halves in front of you so you do not lose the small rubber button pad that sits inside the front cover.
Removing and replacing the battery
Inside the back half of the fob, you will see a small metal holder or clip that holds a round, flat battery. Before you remove the old battery, note which side is facing up — the positive side (marked with a + symbol) or the negative side. This matters because the battery will only work if it is installed the correct way.
Gently pry the old battery out of its holder using the edge of your screwdriver or a fingernail. Drop the new CR2032 battery into the same holder, making sure the same side faces up as the old battery did. The battery should sit flat and snug in the holder; if it falls out when you tilt the fob, you have installed it upside down.
Closing the fob and testing it
Align the front and back halves of the fob so the seams match up. Press them together firmly until you hear or feel a click. The two halves should be flush with no gaps. If the fob does not close all the way, you may have installed the battery upside down or the rubber button pad may be pinched — open it again and check.
Once the fob is closed, stand near your car and press the lock button. You should hear the car lock. Press unlock and listen for the unlock sound. Press the panic button (if your fob has one) and confirm the horn or lights respond. If all buttons work, the battery is installed correctly and you are done. If nothing happens, open the fob again and flip the battery over.
When to replace the battery versus the whole fob
A new battery solves the problem about 95 percent of the time. If you have installed a fresh CR2032 battery and the fob still does not work, the fob itself may be damaged — water inside, a cracked circuit board, or worn-out buttons. At that point, replacing the whole fob is usually cheaper than trying to repair it.
Subaru dealerships sell replacement fobs for $150 to $300 depending on the model year and whether the fob has a physical key blade inside. You can also buy aftermarket fobs online for $30 to $80, though you will need to have a Subaru dealer or a locksmith program it to your car. If the battery replacement does not work, get a quote from your dealership before you buy a replacement fob elsewhere.
Frequently Asked Questions
How long does a CR2032 battery last in a Subaru key fob?
Most CR2032 batteries last three to four years in a key fob, depending on how often you use the buttons. Heavy users may need to replace the battery every two to three years. If your fob suddenly stops working after months of normal use, a dead battery is the most likely cause.
Can I use a different battery type in my Subaru key fob?
No. The fob is designed for a CR2032 specifically. Other coin-cell batteries like CR2025 or CR2016 are different sizes and will not fit properly or may not provide enough power. Always use CR2032.
What if I lose one of the rubber buttons inside the fob when I open it?
The rubber button pad is glued to the inside of the front cover. If it falls out, you can glue it back with a small amount of clear silicone adhesive or contact cement. Let it dry completely before you close the fob. If you lose it entirely, you can order a replacement button pad online for $5 to $15.
Do I need to reprogram my key fob after changing the battery?
No. Changing the battery does not erase any programming. Once you install the new battery and close the fob, it should work when ready without any reprogramming steps.
Is it safe to replace the battery myself, or should I go to a dealer?
It is completely safe to replace the battery yourself. There is no risk of damaging the fob or the car. A dealer will charge you $30 to $75 to do the same five-minute job, so doing it at home saves money and time.