What a wheel bearing does and when it fails
A wheel bearing is a set of steel balls held in a metal ring that lets your wheel spin freely on the axle. When it wears out, you'll hear a grinding or humming noise that gets louder as you speed up, feel vibration in the steering wheel or brake pedal, or notice the wheel pulling to one side. Some cars have sealed bearings that can't be serviced; others have adjustable ones you can sometimes repack with grease before replacement becomes necessary.
Bearings fail because of age, water getting past the seal, or damage from hitting a pothole or curb hard enough to knock the wheel out of alignment. Once a bearing starts to fail, it will get worse. Driving on a completely failed bearing can damage the brake rotor, hub, and axle, turning a $300–$800 repair into a $1,500+ job.
The cost to replace one bearing ranges widely depending on whether your car has a pressed bearing (which requires a hydraulic press and usually means a trip to a shop) or a bolt-on cartridge bearing (which a home mechanic with basic tools can sometimes handle). Front bearings cost more than rear ones because they carry more weight and take more abuse from steering and braking.
Key Takeaways
- A grinding or humming noise that gets louder at highway speed is the most common sign a wheel bearing is failing and needs replacement soon.
- Pressed bearings require a hydraulic press and specialized equipment, so most owners take those to a shop; cartridge bearings can sometimes be replaced at home with hand tools.
- Replacement cost depends on the vehicle, which wheel, and whether the bearing is pressed or bolt-on, ranging from $300 to $800 per wheel at a shop.
- A failed bearing can damage the rotor, hub, and axle if you keep driving, so have the noise diagnosed before it gets worse.
Pressed bearings versus cartridge bearings
Most modern cars use pressed bearings, which are hammered onto the axle shaft with a hydraulic press. Once installed, they stay put and can't be removed without specialized equipment. If one fails, a shop will press the old bearing off, press a new one on, and reassemble the hub. This job typically takes 1 to 2 hours per wheel and requires a press, which is why most home mechanics don't attempt it.
Older cars and some trucks use cartridge bearings or tapered roller bearings that bolt into the hub assembly. These can be removed by unbolting the hub, sliding the bearing out, and sliding a new one in. If your car has this type, you can replace it yourself with a socket set, a torque wrench, and the correct bearing size. Check your owner's manual or a repair guide for your specific vehicle to see which type you have.
Even if you have a cartridge bearing, you'll need to know the exact bearing size and part number. Order the bearing before you start work so you're not left with the wheel off and no replacement on hand. Bearings are not interchangeable between left and right sides on some vehicles, so confirm which side you're working on.
Tools and parts you'll need
For a cartridge bearing replacement at home, gather a socket set, torque wrench, jack and jack stands, wheel chocks, and the correct replacement bearing. You'll also need a seal puller or small pry bar to remove the old seal, and possibly a bearing installer tool if the bearing doesn't slide in by hand. Some bearings come with a new seal; others require you to reuse the old seal or buy one separately.
Before you begin, look up the torque specification for your vehicle's wheel bearing bolts or axle nut. Over-tightening can damage the new bearing; under-tightening can cause it to fail early. Write down the spec and use a calibrated torque wrench, not a ratchet.
If you're taking the car to a shop for a pressed bearing, the shop will supply the bearing and tools. Ask whether the price quote includes a new seal, new bolts (which are often one-time use), and a wheel alignment check afterward, since bearing replacement can shift the wheel's angle slightly.
Step-by-step replacement for cartridge bearings
Raise the car on a jack, find it with jack stands on both sides, and remove the wheel. Unbolt the brake caliper and hang it with a wire so it doesn't dangle from the brake hose. Remove the brake rotor by unbolting it or sliding it off the hub, depending on your car's design.
Unbolt the hub assembly from the steering knuckle or axle housing. Slide the hub away from the axle and set it on a clean work surface. Use a seal puller or small pry bar to remove the old seal from the back of the hub. Tap the old bearing out with a hammer and punch, or use a bearing puller if you have one. Clean the hub bore with a rag to remove any grease or debris.
Slide the new bearing into the hub by hand if it fits, or use a bearing installer tool to tap it in gently and evenly. Install a new seal if one came with the bearing, or reuse the old seal if it's not damaged. Bolt the hub back onto the axle, install the rotor and caliper, and torque all bolts to the specification in your manual. Lower the car and test-drive it to confirm the noise is gone.
When to take it to a shop
If your car has a pressed bearing, a shop is the right choice. The hydraulic press costs thousands of dollars and requires training to use safely. A shop can also diagnose whether the noise is actually a bearing or something else—a worn CV joint, a bad wheel, or a brake pad wear indicator can sound similar.
Take the car to a shop if you don't have a torque wrench, aren't comfortable working under a raised vehicle, or aren't sure whether your bearing is pressed or cartridge. A wrong torque setting or a bearing installed crooked can cause the new bearing to fail within weeks. The labor cost at a shop is usually worth the certainty that the job is done right.
Ask the shop whether they'll reuse your existing rotor or replace it. Some shops replace the rotor as part of the bearing job; others only do it if the rotor is damaged. Get the quote in writing before work starts so there are no surprises when you pick up the car.
Signs the bearing replacement worked
After replacement, the grinding or humming noise should be completely gone. If you still hear it, the new bearing may not be seated correctly, or the noise may have been coming from something else. Take the car back to the shop or mechanic who did the work and ask them to re-inspect.
The steering wheel should feel smooth and centered, and the car should track straight without pulling to one side. If it pulls after the bearing replacement, the wheel alignment may have shifted during the job. Most shops will do a free alignment check if you ask, or charge a small fee to adjust it.
A properly installed bearing should last 100,000 miles or more. If the replacement bearing fails within a few thousand miles, it may have been damaged during installation or the wrong bearing size was used. Contact the shop and ask about their warranty on the work.
Frequently Asked Questions
Can I drive on a bad wheel bearing?
You can drive a short distance to a shop, but not for long. A failing bearing will get worse quickly, and a completely failed bearing can lock up the wheel or cause the rotor to overheat and fail. The longer you wait, the more damage spreads to the hub, axle, and brakes.
How much does a wheel bearing replacement cost?
At a shop, expect $300 to $800 per wheel depending on the vehicle, which wheel, and whether the bearing is pressed or cartridge. Front bearings usually cost more than rear ones. If you replace it yourself with a cartridge bearing, you'll pay only for the bearing part, usually $50 to $200.
Do I need to replace both bearings at the same time?
Only if both are failing. If only one wheel is making noise, only that bearing needs replacement. However, if your car is old and has high mileage, the other bearing may fail soon after, so ask the shop for their opinion based on a test drive.
What's the difference between a sealed bearing and one I can repack?
Sealed bearings are closed and can't be opened to add grease; when they fail, they must be replaced. Older cars with tapered roller bearings can sometimes be repacked with fresh grease, which may extend their life. Check your manual to see which type you have.
Will a bad wheel bearing affect my brakes?
A failing bearing can cause the rotor to warp from heat or vibration, which makes the brakes feel spongy or pulsate. It can also cause uneven brake pad wear. Once the bearing is replaced, the brakes should return to normal if the rotor wasn't damaged.