Ride Tech is an aftermarket suspension brand that specializes in bolt-on systems for classic and vintage vehicles

Ride Tech manufactures complete suspension kits designed to replace or upgrade the original systems on older cars, trucks, and hot rods. The company focuses on vehicles built before modern suspension technology became standard — typically pre-1980s models — and sells direct to consumers and shops. Their kits include coil-over shocks, control arms, sway bars, and mounting hardware engineered to fit specific makes and models.

Unlike universal suspension parts, Ride Tech systems are built for particular vehicles: a 1967 Chevrolet Chevelle kit differs from a 1955 Ford F-100 kit. This specificity matters because older vehicles have different frame geometry, wheel wells, and attachment points than modern cars. A Ride Tech kit accounts for those differences so the parts bolt in without cutting, welding, or major fabrication.

The brand is owned by Holley Performance, a larger automotive aftermarket company, and operates from Ohio. Ride Tech does not manufacture suspension parts for new vehicles or late-model cars — their entire product line targets the classic and custom vehicle market.

Key Takeaways

  • Ride Tech suspension kits are designed for specific classic vehicles, not universal fitment, so you must confirm your exact year, make, and model before ordering.
  • These systems replace worn-out original suspension with modern coil-over shocks and control arms that improve handling and ride quality on older vehicles.
  • Installation typically requires basic hand tools and mechanical knowledge, though many owners have shops perform the work to may support proper setup and alignment.
  • Ride Tech kits cost between $1,500 and $4,000 depending on the vehicle and system complexity, and do not include labor or alignment services.
  • The brand offers technical support by phone and email, and many classic car forums and shops have experience with their products.

What comes in a typical Ride Tech suspension kit

A complete Ride Tech system for a classic vehicle usually includes coil-over shock absorbers, upper and lower control arms, sway bars front and rear, bump stops, and all necessary brackets and fasteners. Some kits also include brake line brackets, wiring harnesses for electronic dampers, and installation instructions specific to your vehicle.

The exact contents depend on which kit level you choose. Ride Tech offers basic kits with passive shocks and premium kits with adjustable coil-overs that let you change ride height and damping stiffness. Higher-end kits may include air suspension options or electronic controls. You select the kit based on your budget and how much adjustability you want after installation.

Ride Tech does not include wheels, tires, or alignment in their kits. You will need to schedule a four-wheel alignment after installation, which typically costs $100 to $200 at a shop. Some shops bundle alignment with installation labor.

How to determine if a Ride Tech kit fits your vehicle

Ride Tech publishes a vehicle compatibility list on their website organized by year, make, and model. You enter your vehicle information and see whether a kit exists for it. If your exact year is not listed, contact Ride Tech directly — sometimes a kit for an adjacent year will fit with minor modifications, but the company needs to confirm this before you order.

The year matters more than you might think. A 1970 Chevrolet Chevelle and a 1972 Chevelle may have different frame dimensions or mounting points, and using the wrong kit can result in poor fitment or parts that do not align correctly. Ride Tech's customer service team can answer fitment questions by phone or email before you commit to a purchase.

If your vehicle is not on the compatibility list, Ride Tech does not make a kit for it. The company does not sell universal suspension systems, and attempting to adapt a kit designed for another vehicle often leads to problems with alignment, clearance, or durability.

Installation options: DIY versus professional shop

Some owners install Ride Tech suspension themselves using basic hand tools, a jack, and jack stands. The process typically takes 8 to 16 hours depending on your mechanical skill and whether you encounter rusted fasteners or other complications. Ride Tech provides installation instructions, and many classic car forums have step-by-step guides from owners who have completed the work.

Many owners choose to have a shop perform the installation, especially if the vehicle has original suspension that has not been disturbed in decades. Rusted bolts, seized components, and frame damage discovered during removal can add time and cost. A shop with experience on classic vehicles can often work around these issues and complete the job in 2 to 4 days.

Installation labor typically ranges from $800 to $2,000 depending on your location and the shop's hourly rate. After installation, you must have the vehicle aligned at a shop equipped to work on classic cars — not all alignment shops can handle older vehicles with non-standard suspension geometry.

Ride Tech suspension versus keeping original suspension

Original suspension on classic vehicles was designed for 1950s or 1960s driving conditions: lower speeds, narrower tires, and less demanding handling. Modern tires and roads expose the limitations of that design. A Ride Tech system improves ride quality on bumpy roads, reduces body roll in corners, and makes the vehicle safer to drive at highway speeds.

Original suspension also deteriorates over time. Bushings crack, shocks lose damping, and springs sag. Replacing individual worn components can cost as much as a complete Ride Tech kit, and you end up with the same old design. A Ride Tech system addresses the entire suspension architecture at once.

The trade-off is that a modern suspension changes how the vehicle feels and looks. Some owners prefer to preserve the original ride and appearance, even if it means a rougher drive. That is a personal choice — Ride Tech kits are reversible in theory, though removing them and reinstalling original parts is rarely done in practice.

Cost breakdown and what affects the price

A basic Ride Tech suspension kit costs between $1,500 and $2,500 for most classic vehicles. Premium kits with adjustable coil-overs, air suspension, or electronic controls run $2,500 to $4,000. These prices are for the parts only and do not include installation labor, alignment, or any additional modifications.

The price depends on your vehicle's complexity. A kit for a common classic like a 1967 Chevrolet Chevelle costs less than a kit for a less common vehicle because Ride Tech manufactures more units and spreads development costs across more sales. Vehicles with unique frame geometry or mounting challenges cost more to engineer.

Installation labor adds $800 to $2,000. Alignment adds $100 to $200. If the shop discovers rust damage, broken fasteners, or frame issues during removal, additional work may be needed. Budget for the parts, labor, and alignment before you start, and ask the shop for an estimate that includes potential complications.

Where to buy Ride Tech suspension and get support

Ride Tech sells directly through their website and through authorized retailers including classic car parts suppliers and online shops. Buying direct from Ride Tech gives you access to their technical support team. Buying through a retailer may offer convenience or local pickup, but you should confirm the retailer offers the same support.

Ride Tech provides technical support by phone and email. Their team can answer fitment questions, help you select the right kit level, and troubleshoot installation issues. Response times are typically one business day. Many classic car forums and Facebook groups also have owners with Ride Tech experience who can offer information.

If you are having the work done at a shop, choose one with experience on classic vehicles and ideally with Ride Tech installations. A shop familiar with the product can often complete the job faster and catch potential issues before they become problems. Ask the shop whether they have installed Ride Tech systems before and request references.

Frequently Asked Questions

Will a Ride Tech kit work on my vehicle if it is not on the compatibility list?

Not without confirmation from Ride Tech first. Contact their customer service team with your vehicle's year, make, model, and any modifications you have made. Sometimes a kit for an adjacent year will fit, but the company must verify this before you order. Do not assume a similar vehicle will work — frame geometry varies even within the same model line.

Can I install a Ride Tech kit myself without special tools?

Most owners can complete installation with basic hand tools, a jack, and jack stands, though 8 to 16 hours of work is typical. The main challenge is removing old, rusted fasteners and components. If your vehicle has original suspension that has not been disturbed in decades, a shop may be safer because they can handle seized bolts and unexpected frame damage without damaging the vehicle.

Do I need an alignment after installing a Ride Tech kit?

Yes. After installation, the vehicle must be aligned at a shop equipped for classic cars. Standard alignment shops may not have the capability to work on older suspension geometry. Budget $100 to $200 for alignment and confirm the shop has experience with classic vehicles before you schedule.

What is the difference between a basic and premium Ride Tech kit?

Basic kits use passive coil-over shocks with fixed damping. Premium kits offer adjustable coil-overs that let you change ride height and shock stiffness after installation. Some premium kits include air suspension or electronic controls. Choose based on your budget and whether you want the ability to fine-tune the suspension after installation.

How long does a Ride Tech suspension last?

Coil-over shocks typically last 50,000 to 100,000 miles before damping degrades and they need replacement. Control arms and bushings last longer if maintained. Ride Tech parts are not lifetime components, but they outlast original suspension on most classic vehicles. Maintenance involves checking fasteners periodically and replacing shocks when they wear out.