What an inner tie rod does and why it fails

An inner tie rod is the part of your steering linkage that connects the steering rack (the component that turns your wheels when you turn the steering wheel) to the outer tie rod, which then connects to your wheel hub. When you turn the wheel, hydraulic pressure or electric motors move the rack, and the tie rods transfer that motion to your wheels. The inner tie rod sits closest to the rack and bears constant stress from turning, bumps, and the weight of the vehicle.

Inner tie rods fail because the rubber boots that protect the ball joints crack or tear, allowing dirt and moisture inside. Once water and road salt reach the joint, corrosion and wear accelerate. You'll notice a loose or clunking feeling in the steering, a vibration at highway speeds, or uneven tire wear. Some vehicles also show a clicking noise when turning sharply. Unlike an outer tie rod, which you can inspect visually, an inner tie rod requires the wheel to be off the ground and the steering to be turned fully to see the damage.

Replacement is not optional once the joint is worn. A failed inner tie rod can cause the wheel to move unpredictably, especially during braking or turning, and in extreme cases can separate entirely. Most shops recommend replacing both inner tie rods at the same time, even if only one is obviously bad, because the other is usually close behind.

Key Takeaways

  • An inner tie rod connects the steering rack to the outer tie rod and must be replaced when the rubber boot tears or the ball joint wears out, typically shown by loose steering or a clunking noise.
  • Replacement requires removing the wheel, unbolting the tie rod from the rack, and installing a new one—a job that usually takes 30 minutes to an hour per side at a shop.
  • Most shops charge between $200 and $400 per tie rod in labor, plus the part cost, which ranges from $50 to $150 depending on whether you choose OEM or aftermarket.
  • After replacement, the vehicle must be aligned because the tie rod length affects your wheel angle, and misalignment will cause tire wear and steering pull.
  • You can replace one tie rod yourself if you have basic tools and a jack, but the alignment afterward requires a shop with alignment equipment.

Tools and parts you need to replace an inner tie rod yourself

If you decide to do the work yourself, you'll need a jack and jack stands to safely lift the vehicle, a socket set (usually 14mm to 19mm depending on your vehicle), a breaker bar for stubborn bolts, and a tie rod removal tool (also called a tie rod puller or pickle fork). The removal tool is essential because the ball joint is tapered and wedged tight; trying to hammer it out or pry it loose will damage the threads or the joint itself. You can rent a tie rod puller from most auto parts stores for $10 to $20, or buy one for $30 to $50.

For the part itself, you have two choices: an OEM (original equipment manufacturer) tie rod from your vehicle's maker, or an aftermarket replacement from a supplier like Moog, Dorman, or TRW. OEM parts typically cost $80 to $150 and carry a warranty from the manufacturer. Aftermarket parts run $50 to $100 and are often just as durable, though quality varies by brand. Many shops use Moog or TRW because they're proven in the field. Buy the part before you start so you know the exact bolt size and can confirm it fits your vehicle.

You'll also need a torque wrench to tighten the new tie rod to the correct specification—usually between 35 and 50 foot-pounds depending on your vehicle. Undertightening can cause the joint to loosen; overtightening can strip the threads or crack the housing. Check your vehicle's service manual or the parts supplier's instructions for the exact torque value.

Step-by-step replacement process

Start by loosening the wheel lug nuts while the vehicle is still on the ground, then jack up the vehicle and find it on jack stands. Remove the wheel and set it aside. Locate the inner tie rod, which is bolted to the steering rack under the vehicle near the center. You may need to remove a splash shield or other components to access it.

Use your socket set to unbolt the tie rod from the rack. There is usually one bolt or nut holding it in place. Once the bolt is out, use the tie rod removal tool to separate the ball joint from the rack. Position the tool's jaws around the joint, tighten the center screw, and the wedge will push the joint free. Do not hammer on the tie rod itself; the removal tool does the work.

With the old tie rod removed, thread the new one into place by hand first to avoid cross-threading. Once hand-tight, use your socket and torque wrench to tighten it to the specification in your manual. Reinstall any splash shields, put the wheel back on, and lower the vehicle. Repeat on the other side if you're replacing both.

After both tie rods are installed, you must have the vehicle aligned at a shop. The inner tie rod length affects the toe angle (the angle of the wheels relative to the centerline of the vehicle), and even a small error will cause the vehicle to pull to one side and wear the tires unevenly. Alignment typically costs $100 to $200 and takes 30 to 60 minutes.

Labor costs at a shop versus doing it yourself

A typical shop will charge $200 to $400 per inner tie rod in labor, plus the cost of the part. For both sides, expect $400 to $800 in labor alone. Add the part cost ($50 to $150 each, so $100 to $300 for both) and the alignment ($100 to $200), and the total bill ranges from $600 to $1,300 depending on your vehicle and your location.

If you do the work yourself, you save the labor cost but must still pay for the parts and the alignment. Your out-of-pocket cost drops to $250 to $500 (parts plus alignment), assuming you already own basic tools. The trade-off is time and the risk of making a mistake—if you cross-thread the bolt or damage the rack, the repair becomes much more expensive.

Some shops offer a middle ground: you buy the parts and bring them in, and the shop installs them and aligns the vehicle. This usually costs $150 to $250 in labor per tie rod, saving you money compared to buying the part from the shop but still giving you professional installation and alignment.

Signs your inner tie rod is failing

The most common sign is loose or sloppy steering—you turn the wheel and feel a delay before the vehicle responds, or the steering wheel moves more than it should before the wheels turn. This happens because the worn ball joint has play in it, and that play adds up across the steering linkage.

A clunking or clicking noise when turning sharply is another red flag. The worn joint rattles in its socket as the vehicle leans into the turn. The noise is usually loudest at full lock (steering wheel turned all the way to one side).

Uneven or rapid tire wear, especially on the inside or outside edge of the tire, suggests the wheels are not tracking straight. This can be caused by a worn tie rod, but it can also be caused by other suspension problems, so have it inspected.

A vibration in the steering wheel at highway speeds may indicate a worn tie rod, though it can also come from wheel imbalance, a bent rim, or worn CV joints. The key is that the vibration usually gets worse when you turn the wheel slightly, because turning loads the worn joint differently.

When to replace both inner tie rods at the same time

Most mechanics recommend replacing both inner tie rods together, even if only one is obviously worn. The reason is straightforward: if one has failed, the other is usually close behind. Both sides experience the same stress, the same road salt, and the same age. Replacing only one means you'll likely be back under the vehicle in a few months to replace the other, paying for labor and alignment twice.

The exception is if one tie rod was damaged in an accident or collision and the other is still in good condition. In that case, replacing just the damaged one is reasonable. But if both are worn from normal use, doing both at once saves money and time in the long run.

Some shops will inspect the other tie rod while they have the vehicle up and give you a clear picture of its condition. If it's visibly cracked or the boot is torn, replacement is justified. If it looks fine, you can wait, though many shops still recommend doing both for the reasons above.

Alignment after tie rod replacement

Alignment is not optional after replacing an inner tie rod. The tie rod length directly affects the toe angle—the angle at which the wheels point relative to the centerline of the vehicle. If the toe is off, the tires will scrub sideways as you drive, causing rapid wear and a pulling sensation toward the side with more toe-in.

A shop will use an alignment machine to measure the toe, camber, and caster of both front wheels and adjust them to the manufacturer's specification. This usually takes 30 to 60 minutes and costs $100 to $200. Some shops include alignment in the tie rod replacement price; others charge it separately. Ask before you authorize the work.

If you replace the tie rod yourself, you still need professional alignment. Do not skip this step hoping the vehicle will "settle in" or that the alignment will be close enough. Misalignment will cost you in tire wear within a few thousand miles, and it affects how the vehicle handles in emergency maneuvers.

Frequently Asked Questions

Can I drive on a bad inner tie rod?

You can drive short distances, but it's not safe. A worn inner tie rod makes steering unpredictable, especially during braking or in emergency maneuvers. In extreme cases, the joint can separate, causing sudden loss of steering control. Have it inspected and replaced as soon as possible.

How long does an inner tie rod last?

Inner tie rods typically last 70,000 to 100,000 miles, but this varies widely depending on driving conditions, road salt exposure, and how often you hit potholes. Vehicles driven in areas with heavy salt use or rough roads may need replacement sooner. Regular inspection of the rubber boots can catch wear early.

What's the difference between an inner and outer tie rod?

The inner tie rod connects the steering rack to the outer tie rod, which then connects to the wheel hub. The outer tie rod is more exposed and easier to inspect visually. Both can wear out, and both affect steering. Outer tie rods are usually cheaper to replace because they're easier to access.

Do I need an alignment if I replace just one inner tie rod?

Yes. Even replacing one tie rod changes the toe angle on that side, so alignment is necessary. Some shops will do a single-side alignment if only one tie rod was replaced, which costs less than a full four-wheel alignment but still corrects the problem.

Can a bad inner tie rod cause a steering wheel to pull to one side?

Yes, especially if one tie rod is much more worn than the other. The worn side has more play, which can cause the vehicle to pull toward the tighter side. However, pulling can also be caused by uneven tire pressure, brake problems, or suspension wear, so have a shop diagnose it before assuming it's the tie rod.