What a lorry suspension system does

A lorry suspension system connects the wheels to the frame and absorbs the shock of bumps, potholes, and uneven road surfaces. Without it, every impact would transfer directly to the cargo, the driver, and the structural integrity of the vehicle. The suspension also keeps the wheels in contact with the road, which is essential for steering control and braking.

Heavy goods vehicles (HGVs) use more complex suspension than cars because they carry much heavier loads and travel longer distances. The system has to manage the weight of the lorry itself plus whatever cargo is loaded on it, sometimes totalling 40 tonnes or more. A well-maintained suspension keeps that load stable, reduces wear on tyres and brakes, and makes the vehicle safer to handle in corners and emergency stops.

Key Takeaways

  • Lorry suspensions use springs, dampers, and linkages to absorb road shocks while keeping wheels in contact with the road surface.
  • Air suspension and leaf spring suspension are the two main types used on HGVs, each with different maintenance needs and load-handling characteristics.
  • Suspension condition directly affects braking distance, tyre wear, fuel consumption, and the safety of the load being carried.
  • Regular checks of springs, dampers, bushings, and linkages can prevent expensive repairs and reduce the risk of roadside failure.

Leaf spring suspension on lorries

Leaf spring suspension uses stacked metal strips (leaves) that flex under load and then return to their original shape. Each leaf is slightly curved, and they are clamped together at the centre. When the lorry hits a bump, the leaves bend, absorbing the energy. When the bump passes, they straighten again. This design has been used on heavy vehicles for decades because it is robust and can handle very heavy loads without complex hydraulics.

Leaf springs wear over time as the leaves rub against each other and lose their ability to flex smoothly. The clamps that hold the leaves together can corrode or loosen, and individual leaves can crack or break. A broken leaf spring on one side of the axle will cause the lorry to sit lower on that side, which throws the weight distribution off and puts extra stress on the other suspension components. Leaf springs also transmit more road vibration to the cab than air suspension, which is why drivers often feel every bump.

Maintenance involves checking that all leaves are intact, that the clamps are tight, and that the springs are not sagging unevenly. Greasing the pivot points where the springs attach to the frame helps prevent rust and keeps them moving freely. When a leaf breaks, the entire spring assembly usually needs to be replaced rather than repaired.

Air suspension on modern lorries

Air suspension uses pressurised air in rubber bellows (air springs) instead of metal springs. The air acts as a cushion that compresses when the lorry hits a bump and expands when the bump passes. A compressor maintains the correct air pressure, and a control system adjusts the pressure automatically based on the load and road conditions. This gives a much smoother ride than leaf springs and reduces vibration in the cab and cargo area.

Because air suspension is adjustable, it can keep the lorry level even when the load is unevenly distributed or when cargo is loaded and unloaded. This is especially useful for vehicles that carry different types of cargo or that need to kneel down (lower themselves) to load and unload at ground level. Air suspension also reduces wear on tyres because the wheels stay in better contact with the road surface.

The downside is complexity. Air suspension relies on the compressor, air lines, valves, and electronic sensors all working together. A leak in an air line, a faulty compressor, or a failed sensor can cause the system to lose pressure, which will make the lorry sag and become unsafe to drive. Air springs themselves can develop leaks or rupture, especially if the lorry is overloaded or if the suspension is not serviced regularly. Repairs usually require specialist equipment and knowledge.

Dampers and how they control bounce

Springs alone would make a lorry bounce up and down for a long time after hitting a bump. Dampers (also called shock absorbers) are hydraulic cylinders that slow down this bouncing by converting the energy into heat. They work by forcing fluid through small openings as the suspension compresses and extends, creating resistance that gradually brings the oscillation to a stop.

A worn damper will allow the lorry to bounce excessively, which makes the ride uncomfortable, reduces steering control, and causes the wheels to lose contact with the road during braking. This increases stopping distance and makes the vehicle harder to control in an emergency. Dampers wear out gradually, so the deterioration is often not obvious until the problem is severe. A straightforward test is to push down hard on the corner of the lorry and count how many times it bounces after you let go. If it bounces more than twice, the dampers need attention.

Dampers should be checked during routine servicing and replaced in pairs (both sides of an axle) to maintain even handling. The intervals vary depending on the lorry's age, load, and driving conditions, but many operators replace them every two to three years or when they fail a bounce test.

Bushings, linkages, and alignment

The suspension is connected to the frame and axles through a network of metal rods and joints called linkages. These linkages are held in place by rubber or polyurethane bushings that allow a small amount of movement while absorbing vibration. Over time, bushings crack, harden, or separate from the metal, which allows the linkages to move more than they should. This causes clunking noises, uneven tyre wear, and poor steering response.

Worn bushings also affect wheel alignment. If the suspension geometry shifts because bushings have failed, the wheels will no longer point straight ahead or sit at the correct angle to the road. This causes rapid tyre wear on one edge, increases fuel consumption, and makes the lorry pull to one side when braking. Alignment should be checked whenever suspension work is done or if you notice uneven tyre wear.

Linkage inspection is part of a routine pre-trip check. Look for cracks in the rubber, movement where there should be none, and any visible separation between the rubber and metal. Bushings are relatively inexpensive to replace compared to the cost of premature tyre wear or a suspension failure on the road.

How suspension condition affects safety and running costs

A failing suspension system increases braking distance because the wheels lose contact with the road surface during hard stops. It also makes the lorry more likely to roll in a sharp turn, especially when carrying a high load. Poor suspension control can cause cargo to shift, which changes the centre of gravity and makes the vehicle unstable. For a loaded HGV, this is a serious safety risk.

Suspension problems also drive up running costs. Worn suspension causes uneven tyre wear, which means tyres need replacing more often. It increases fuel consumption because the engine has to work harder to move a vehicle that is bouncing and not rolling smoothly. Damaged suspension components can fail completely, leaving the lorry stranded and requiring an expensive roadside recovery and repair.

Regular suspension maintenance — checking springs, dampers, bushings, and linkages — costs far less than dealing with these consequences. Many operators include suspension checks in their routine servicing schedule, especially for vehicles that carry heavy or variable loads or that operate in rough terrain.

Frequently Asked Questions

How often should a lorry suspension be serviced?

Most manufacturers recommend a full suspension inspection every 12 months or 100,000 kilometres, whichever comes first. Vehicles operating in harsh conditions, carrying heavy loads, or with high mileage may need more frequent checks. Always follow the maintenance schedule in your vehicle's handbook.

What does it mean if my lorry is sitting lower on one side?

This usually indicates a broken or sagging spring on that side, a failed air spring if you have air suspension, or a severely worn damper. It means the load is not being supported evenly, which puts extra stress on the other suspension components and the tyres. Have it inspected and repaired before driving long distances.

Can I drive with a leaking air suspension?

Not safely. A leak will cause the air pressure to drop, which means the suspension cannot support the load properly. The lorry will sag, braking and handling will be affected, and you risk damaging other components. Have the leak found and repaired before returning to the road.

Why does my lorry pull to one side when I brake?

This can be caused by worn suspension bushings that have shifted the wheel alignment, a damaged damper on one side, or uneven spring wear. It can also indicate a brake problem. Have both the suspension and brakes inspected to identify the cause.

What is the difference between air and leaf spring suspension for load carrying?

Leaf springs are simpler and more durable for very heavy loads, but they transmit more vibration and cannot adjust to uneven loading. Air suspension is smoother, adjusts automatically to load, and keeps the lorry level, but it is more complex and requires more maintenance. The choice depends on the type of work the lorry does.