The track bar keeps your XJ's axle centered under the frame

The track bar (also called a panhard bar) is a single rod that connects your XJ's rear axle to the frame, running side-to-side underneath the vehicle. Its job is to stop the axle from sliding left or right when you turn, brake, or hit bumps. Without it, the axle would wander around and your rear end would feel loose and unpredictable.

On a stock XJ, the track bar bolts to the axle housing on one end and the frame on the other. It's a straightforward part—just a rod with bushings and bolts—but it carries real load. When it wears out or breaks, you'll feel it when ready as wandering in the rear, especially at highway speeds or when cornering hard.

Key Takeaways

  • The track bar prevents side-to-side axle movement and is critical for handling and safety on any XJ.
  • Worn bushings or a bent bar cause rear-end wandering, clunking noises, and uneven tire wear.
  • Replacement takes two to four hours and costs between $150 and $400 for parts and labor, depending on whether you replace bushings and whether you go OEM or aftermarket.
  • Lifted XJs often need a longer or adjustable track bar to maintain correct axle geometry and prevent binding.
  • A broken track bar is not safe to drive on—get it fixed before your next trip.

Signs your XJ's track bar is failing

The most obvious symptom is rear-end wandering—the back of the vehicle feels like it's moving side to side, especially noticeable on the highway or when you're not actively steering. You might also feel a clunk or knock from underneath when you hit a bump or turn sharply. This is usually the bushings at either end of the bar wearing out and allowing play.

Uneven tire wear on the rear tires, particularly more wear on one edge than the other, can point to a track bar problem. If the bar is bent (usually from hitting a rock or pothole hard), the axle sits off-center and the tires wear unevenly. You may also notice the vehicle pulls slightly to one side even when the steering wheel is straight.

In severe cases, a completely broken track bar will make the rear end feel completely loose, and you might see the axle visibly shifted to one side when you look underneath. This is a safety issue and should be addressed when ready.

OEM versus aftermarket track bars for the XJ

The OEM Jeep track bar is the factory part, designed to work with the stock suspension geometry. It's reliable and straightforward to install. Expect to pay $80 to $150 for the part alone, plus labor. If you're keeping your XJ stock or close to it, OEM is the simplest choice.

Aftermarket bars come in two main types: heavy-duty replacements (stiffer material, better bushings) and adjustable bars (length can be changed). Heavy-duty bars run $120 to $200 and are good if you want something that will last longer than stock. Adjustable bars cost $180 to $300 and are essential if you've lifted your XJ, because a lifted suspension changes the angle of the stock bar and can cause binding or premature wear.

Brands like Rough Country, Currie Enterprises, and Synergy offer XJ-specific bars. Read reviews from other XJ owners on forums—real-world feedback matters more than marketing claims for suspension parts.

Why lifted XJs need a different track bar

When you lift an XJ, the suspension geometry changes. The stock track bar was designed for the factory ride height and angle. A lift raises the axle, which changes the angle at which the bar pulls on the axle and frame. If the angle gets too steep, the bar can bind (resist movement) or wear out faster because it's fighting the suspension instead of working with it.

An adjustable track bar lets you change the length to keep the axle centered and the bar at the correct angle relative to your new ride height. This is not optional if you've lifted more than 2 inches—a misaligned bar will cause clunking, wandering, and accelerated wear on bushings and tires. Most adjustable bars come with instructions for measuring and setting the correct length for your lift height.

How to replace an XJ track bar yourself

You'll need a jack, jack stands, a socket set, a wrench, and possibly a pry bar. Lift the rear of the vehicle safely on jack stands—never work under a vehicle supported only by a jack. Locate the track bar bolts: one at the axle housing (usually a 13mm or 15mm bolt) and one at the frame (same size). Remove both bolts and the bar will come free.

If you're reusing the bolts, clean them. If the bushings are worn (rubber looks cracked or compressed), replace them now—they're cheap and it's the right time. Install the new bar, hand-tighten the bolts first, then lower the vehicle onto its wheels before final tightening. This ensures the suspension is at normal ride height and the bar isn't under stress. Torque the bolts to the specification in your service manual (typically 35 to 50 foot-pounds for XJs, but verify).

The whole job takes two to three hours if you're comfortable with basic tools. If you're not, a shop will charge $150 to $250 in labor on top of the part cost.

Track bar bushings and when to replace them

The bushings are the rubber or polyurethane sleeves that sit between the bar and the bolts at each end. They absorb vibration and allow the bar to flex slightly. Over time, they compress, crack, and wear out. You can replace just the bushings without replacing the whole bar if the bar itself is straight and undamaged.

Polyurethane bushings last longer than rubber and handle off-road use better, but they're stiffer and transmit more vibration into the cabin. Rubber bushings are quieter but wear faster. A full bushing replacement kit costs $30 to $60 and takes an hour or two if you're comfortable pressing bushings. Many shops will do this for $75 to $150 in labor.

If the bar is bent or the bushings are severely deteriorated, replacing the whole assembly is usually the better move. A new bar with fresh bushings is more reliable than trying to salvage an old bar.

Frequently Asked Questions

Can I drive my XJ if the track bar is broken?

No. A broken track bar means your rear axle can move freely side to side, which makes the vehicle unsafe to control, especially at speed or in turns. The rear end can slide unexpectedly. Get it fixed before driving.

How long does a track bar usually last on an XJ?

On a stock XJ driven normally, 80,000 to 150,000 miles is typical. Off-road use, lifting, or rough roads shorten that. Bushings usually wear out before the bar itself bends or breaks.

Do I need an alignment after replacing the track bar?

Not usually, unless the old bar was bent and the axle was off-center. If you replaced it because of wear (not damage), a standard alignment check is fine. If you installed an adjustable bar on a lifted XJ, you may need to adjust it for proper axle centering, which some shops can do without a full alignment.

What's the difference between a track bar and a sway bar?

The track bar controls side-to-side axle movement. The sway bar (anti-roll bar) reduces body lean when you turn. They're separate parts doing different jobs. A worn track bar causes axle wandering; a worn sway bar causes the body to roll more in corners.

Should I replace both the track bar and bushings at the same time?

If you're already under the vehicle with the bar off, replacing the bushings adds little cost and time. New bushings may support the bar works properly and last longer. It's worth doing together.