What to look for when checking a CV joint

A CV joint (constant velocity joint) connects your axle to your wheels and lets power flow to them while the suspension moves and the wheels turn. When a CV joint starts to fail, you'll usually hear a clicking sound when turning, see grease splattered inside the wheel, or feel vibration at highway speed. You can do a basic visual inspection yourself in about 15 minutes with the car on jack stands and the wheel removed.

The joint itself is covered by a rubber or plastic CV boot — a accordion-like sleeve that keeps grease in and dirt out. If that boot tears, the joint will fail within weeks or months. A torn boot is the easiest problem to catch early, and it's cheaper to replace just the boot than to replace the whole joint later.

Most cars have two CV joints per axle — one at the wheel (the outer joint) and one at the transmission (the inner joint). The outer joint is easier to inspect because it's more exposed. Both can fail, but outer joints fail more often because they handle more stress when you turn.

Key Takeaways

  • A torn CV boot is the first sign of trouble and the cheapest time to fix it — inspect the rubber sleeve around each joint for cracks or splits.
  • Grease splattered on the inside of the wheel or the underside of the fender means the boot has already torn and the joint is losing lubrication.
  • A clicking or popping sound when turning, especially at full lock, is a classic symptom of a worn outer CV joint.
  • You can do a basic visual check yourself with the car on jack stands, but a mechanic's inspection under load (driving the car) catches problems you might miss.

How to inspect the CV boot visually

Raise the car safely on jack stands — never work under a car supported only by a jack. Remove the wheel to expose the axle. Look at the rubber or plastic sleeve that wraps around the CV joint. It should be smooth and intact with no cracks, splits, or holes. If you see a tear, even a small one, the boot has failed and the joint is already losing grease.

Run your finger along the boot seams where it connects to the axle shaft and the joint housing. Seams are common failure points because they flex constantly. If the seam is separating or the rubber is peeling away, treat it as a torn boot. Also check for grease that has been forced out through a small tear — it will look like a dark, sticky coating on the boot or the surrounding area.

Inspect both the outer joint (closer to the wheel) and the inner joint (closer to the transmission). The inner joint is harder to see on some cars, so you may need to turn the wheel or move the suspension to get a clear view. If you find a torn boot on one side, check the other side too — if one joint has failed, the other is often close behind.

Signs of grease leakage and joint damage

If the CV boot has torn, grease will leak out and you'll see it on the inside of the wheel, on the brake rotor, or splattered on the inside of the fender. The grease is dark brown or black and sticky. This is a sign that the joint has already lost lubrication and wear is accelerating. A joint that has lost its grease will fail completely within weeks to a few months of hard driving.

Look also for rust or discoloration on the joint housing itself. A joint that has been running dry will show surface rust or a dull, pitted appearance. If the boot is torn and the joint looks rusty, the joint itself is likely damaged and will need to be replaced, not just the boot.

Check the axle shaft for cracks or bending near the joint. A bent axle is rare but can happen if you've hit a pothole hard or bottomed out the suspension. A bent axle will cause vibration and clicking even if the joint itself is intact, and it will need to be replaced.

Testing a CV joint by hand and by ear

With the car on jack stands and the wheel removed, grab the axle shaft near the joint and try to move it up and down and side to side. There should be almost no play — the joint should feel solid and tight. If you can move it more than a quarter inch in any direction, the joint is worn and needs replacement. This test works best on the outer joint, which is easier to access.

For the inner joint, you may need to remove the wheel and turn the steering wheel fully to one side to see it clearly. Grab the axle shaft on either side of the inner joint and check for play the same way. Inner joints wear more slowly than outer joints, but a worn inner joint will feel loose and sloppy.

Have someone turn the steering wheel fully left and right while you listen near the wheel. A clicking or popping sound that speeds up as the car turns faster is a sign of a worn outer CV joint. The sound happens because the joint is no longer round — wear has made it slightly egg-shaped, so it clicks once per revolution. This test is most reliable at low speed in a parking lot.

When to replace the boot versus the whole joint

If the boot is torn but the joint itself feels tight and sounds normal, a boot replacement is usually enough. A boot kit costs between $20 and $80 depending on the car, and a mechanic can install it in 30 to 60 minutes. This is the cheapest repair and the one to do as soon as you spot a torn boot.

If the joint has play, makes noise, or the boot has been torn for a long time, the joint itself is likely damaged and needs replacement. A CV joint assembly costs between $150 and $400 depending on the car, and labor is usually 1 to 2 hours. Some shops offer remanufactured joints, which cost less than new ones and carry a warranty.

If you catch a torn boot early — within a few weeks of the tear — a boot replacement alone may save you the cost of a full joint replacement. This is why regular visual inspections matter. Once a joint has run dry for months, the internal races and balls wear out and the joint will fail even if you replace the boot.

What a mechanic checks that you might miss

A mechanic will do a test drive to listen for clicking under load and feel for vibration at highway speed. These tests reveal wear that a stationary inspection can't catch. A joint that feels tight on jack stands may still be worn enough to click when the car is turning at speed and the joint is under full load.

A mechanic will also remove the wheel and inspect the brake components, suspension bushings, and other parts of the steering and suspension system at the same time. Sometimes a clicking sound that sounds like a CV joint is actually a worn suspension bushing or a loose brake pad. A full inspection rules out these other causes.

If you're unsure whether a joint needs replacement or just a boot, a mechanic's inspection is worth the cost. Most shops charge $50 to $100 for a suspension inspection, and they can tell you exactly what needs to be done and what can wait.

Frequently Asked Questions

What does a bad CV joint sound like?

A worn outer CV joint makes a clicking or popping sound that gets faster as you turn tighter or drive faster. The sound is usually loudest when turning at full lock — for example, making a sharp left turn in a parking lot. An inner joint that's failing may cause a clunking sound when accelerating or decelerating, rather than a clicking sound.

Can I drive on a torn CV boot?

You can drive short distances on a torn boot, but the joint will lose grease quickly and fail within weeks or months of regular driving. The longer you wait, the more damage the joint sustains and the more expensive the repair becomes. If you catch a torn boot early, a boot replacement is cheap and fast.

How long does a CV joint last?

A CV joint that's properly lubricated can last the life of the car — often 150,000 miles or more. A joint that loses its grease because the boot tore will fail within weeks to a few months. Aggressive driving, frequent hard turns, and rough roads can shorten the life of a joint even if the boot is intact.

Is a clicking sound always a CV joint?

Clicking can come from a worn CV joint, but it can also come from a loose brake pad, a worn suspension bushing, or a bent axle. A mechanic can pinpoint the source by listening to where the sound comes from and testing the suspension under load. Don't assume it's a CV joint without having it checked.

Can I replace just one CV joint?

Yes, you can replace one joint at a time. However, if one joint has failed, the other joint on the same axle is often close behind. Some mechanics recommend replacing both joints on an axle at the same time to avoid a second repair soon after, but it's not required. Ask your mechanic whether the other joint shows signs of wear before deciding.