The Ford 9-Inch Third Member Explained

The third member is the removable center section of a Ford 9-inch rear axle — the part that bolts into the axle housing and contains the differential, ring gear, and pinion gear. It's called the "third member" because it's technically a separate assembly you can unbolt and swap out without replacing the entire axle housing. If you're rebuilding a 9-inch axle or upgrading to a stronger differential, you're usually replacing the third member, not the whole rear end.

Ford 9-inch axles are common in older Mustangs, Torinos, and other mid-size cars, as well as in some trucks and hot rods. The third member is what determines how your engine's power gets split between the rear wheels — through gear ratios, locking differentials, or limited-slip designs. When a 9-inch third member fails, you'll hear noise, feel vibration, or lose traction. When you want more power handling or a different gear ratio, swapping the third member is often cheaper than replacing the whole axle.

Key Takeaways

  • The third member is the bolt-in center section of a Ford 9-inch axle that holds the differential and gears, and you can replace it without replacing the entire housing.
  • Common reasons to replace a third member include bearing wear, gear damage, or upgrading to a locking or limited-slip differential for better traction.
  • Third members come in different gear ratios and differential types, so you need to match your engine power and driving style when ordering a replacement.
  • Installation requires removing the axle shafts, unbolting the old third member, and pressing or bolting in the new one — a job most home mechanics can do with basic tools and a lift.
  • Ford 9-inch third members are widely available new, remanufactured, or used, with prices ranging from a few hundred dollars for salvage units to over $2,000 for new assemblies with premium differentials.

When a Third Member Fails and What You'll Notice

A failing third member usually announces itself with noise. You'll hear a whine or grinding sound from the rear axle, especially under acceleration or when coasting. This typically means the ring gear and pinion gear are worn or damaged, or the bearings that support them are failing. The noise gets worse as you drive because metal-on-metal contact spreads the damage.

You might also feel vibration through the chassis, or notice that one rear wheel spins freely while the other doesn't — a sign the differential is broken internally. If the third member seals fail, you'll see gear oil leaking from the axle housing. Any of these signs means the third member needs to come out and be rebuilt or replaced.

Rebuilding an old third member is possible if the housing and gears aren't too damaged, but it requires a machine shop with the right equipment and informed. For most people, buying a replacement third member — either new, remanufactured, or used — is faster and more reliable than trying to salvage the old one.

Third Member Gear Ratios and Differential Types

When you order a replacement third member, you're choosing both a gear ratio and a differential type. The gear ratio (written as something like 3.50:1 or 4.11:1) determines how many times the ring gear turns for each turn of the driveshaft. A lower number like 3.00 gives you better highway fuel economy and top speed; a higher number like 4.56 gives you faster acceleration and better towing power.

The differential type controls how power splits between the left and right rear wheels. A standard open differential is the cheapest but lets the wheel with less traction spin freely — bad for traction in snow or mud. A limited-slip differential (often called a Traction-Lok on Ford axles) uses friction discs to limit wheel spin and keep both wheels turning. A locking differential (selectable or automatic) locks both wheels together for maximum traction off-road or in deep snow.

Your choice depends on how you drive. Street cars usually run a limited-slip with a ratio matched to the engine size — a big-block engine needs a lower ratio to avoid bogging down. Off-road vehicles often use a locking differential. Check your original ratio by counting the ring gear teeth and dividing by the pinion gear teeth, then decide if you want to stay the same or go higher or lower.

Finding the Right Replacement Third Member

Ford 9-inch third members are widely available because the axle has been in production since 1957 and is popular in the hot rod and restoration community. You can buy new third members from axle specialists, remanufactured units from rebuilders, or used cores from salvage yards or online marketplaces.

When shopping, you need to know your original gear ratio and differential type so you can order the right one. If you're upgrading, decide on your new ratio and differential before you buy. Some sellers offer third members already assembled and ready to bolt in; others sell the housing and gears separately so you can have a shop assemble them to your specs.

Prices vary widely. A used third member from a salvage yard might cost $200 to $400. A remanufactured unit with a warranty runs $600 to $1,200. A brand-new third member with a premium differential can exceed $2,000. Factor in the cost of new bearings, seals, and gaskets if you're doing the work yourself, or labor costs if a shop is doing it.

Removing and Installing a Third Member

Removing a third member is straightforward if you have the right tools. Lift the rear axle on jack stands, remove the wheels, and unbolt the brake drums or calipers. Drain the gear oil from the housing. Unbolt the axle shafts from the third member (or remove the C-clips if your axle uses them), then unbolt the third member itself — usually 8 to 12 bolts around the center of the housing.

The third member will be heavy and may be stuck, so use a pry bar and tap it gently with a hammer to break it loose. Once it's out, you can inspect the housing for damage, clean it, and install the new or rebuilt third member. Bolt it back in with a new gasket and torque the bolts to the factory spec — usually around 30 to 40 foot-pounds for Ford 9-inch axles.

Reinstall the axle shafts, refill the housing with the correct gear oil (usually 80W or 80W-90), and bleed the brakes if you disturbed the lines. The whole job takes 2 to 4 hours for someone with basic mechanical skill and access to a lift. If you don't have a lift or press, a shop can do it for $300 to $600 in labor.

Upgrading Your Third Member for More Power

Many people replace a third member not because it failed, but because they want better traction or a different power delivery. If you've added horsepower to your engine or want to tow heavier loads, a stronger differential or a lower gear ratio can make a big difference.

Upgrading to a limited-slip or locking differential from an open one is one of the most common upgrades. It costs more upfront but dramatically improves traction in snow, rain, or off-road conditions. Changing the gear ratio is another popular move — going from a 3.50 to a 4.11 ratio, for example, will make your car feel quicker off the line but will lower your top speed and fuel economy slightly.

Before you upgrade, think about your real-world use. A street car that sees mostly highway driving doesn't need a locking differential. A truck that tows or goes off-road does. A muscle car that sees occasional track days might benefit from a lower ratio and a limited-slip. Talk to other owners of the same vehicle and engine combination to see what they run.

Frequently Asked Questions

Can I use a third member from a different Ford vehicle in my axle housing?

Sometimes, but not always. Ford 9-inch housings come in different widths (narrow, medium, and wide track), and the third member has to match. A narrow-track third member won't fit in a wide-track housing. Check the width of your housing and the third member you're buying to make sure they match. Some specialty shops can modify housings or third members to make them work together, but that adds cost and complexity.

What's the difference between a remanufactured and a used third member?

A remanufactured third member has been disassembled, inspected, and rebuilt by a shop using new bearings, seals, and gaskets. It usually comes with a warranty and is more reliable than a used core pulled from a salvage yard. A used third member is as-is — you don't know its history or how much life is left in the bearings and gears. Used is cheaper but riskier; remanufactured costs more but is more predictable.

Do I need to change my gear ratio if I add a supercharger or turbo?

Not necessarily, but you should think about it. A supercharger or turbo adds power across the RPM range, which can make your car feel sluggish off the line if your gear ratio is too high (like 3.00). Going to a 3.73 or 4.11 ratio will help the engine pull harder and make the car feel quicker. Talk to other owners with the same engine and boost setup to see what ratio they use.

Can I install a third member myself if I've never done it before?

Yes, if you have a lift, jack stands, basic hand tools, and a torque wrench. The job is mostly unbolting and rebolting, which is straightforward. The hardest part is breaking the old third member loose and making sure you torque the bolts correctly. If you don't have a lift or aren't comfortable working under a car, a shop is worth the cost — a mistake here can damage your axle or brakes.

How do I know what gear ratio my Ford 9-inch currently has?

Count the number of teeth on the ring gear and divide by the number of teeth on the pinion gear. You'll need to remove the third member or look through the inspection cover on the back of the housing. The ratio is also sometimes stamped on the housing itself. If you can't find it, a shop can identify it by spinning the driveshaft and counting how many times the wheels turn.