What electric power steering conversion means and when it makes sense
Electric power steering (EPS) conversion replaces your car's hydraulic power steering system with an electric motor and control module. The electric motor does the work that hydraulic fluid pressure used to do, making the steering wheel easier to turn without the constant drain on your engine.
Most conversions happen on older vehicles — cars from the 1960s through 1980s — because they came with manual steering or heavy hydraulic systems that consumed fuel and generated heat. A modern EPS system is lighter, more responsive, and doesn't pull power from the engine while you're parked or driving straight. You'll notice the difference most on long drives or in tight parking situations.
The trade-off is cost and complexity. A full EPS conversion runs between $2,000 and $6,000 in parts and labor, depending on your vehicle and whether you're doing the work yourself. You're also committing to a system that requires electrical troubleshooting if something goes wrong, rather than the straightforward hydraulic repairs most mechanics know.
Key Takeaways
- Electric power steering conversion replaces hydraulic pressure with an electric motor, reducing engine load and improving fuel economy on older vehicles.
- The conversion typically costs between $2,000 and $6,000 in parts and labor, with prices varying based on your vehicle's make and year.
- Older cars with manual or heavy hydraulic steering see the biggest practical benefit, while newer vehicles already have EPS from the factory.
- You'll need a compatible EPS unit designed for your vehicle's steering column, a control module, wiring harness, and often a new steering wheel or adapter.
- Aftermarket EPS systems require electrical knowledge to install and troubleshoot, so factor in professional labor costs if you're not experienced with wiring.
How electric power steering actually works in your car
In a hydraulic system, your engine drives a pump that pressurizes fluid, and that pressure moves a piston connected to your steering linkage. The harder you turn the wheel, the more pressure the system needs. This constant work drains fuel economy and generates heat that requires cooling.
An electric system uses a motor mounted on or near your steering column. When you turn the wheel, a sensor detects the movement and tells the motor how much information to provide. The motor only works when you're actually steering — sitting still in traffic or driving straight uses almost no power. This is why EPS improves fuel economy on older vehicles and reduces the load on an aging engine.
The control module is the brain of the system. It reads input from the steering angle sensor, wheel speed sensors, and sometimes vehicle speed, then commands the motor to provide the right amount of information. Different modules offer different tuning — some mimic the feel of manual steering, others provide heavier information for easier parking.
Parts you'll need for a complete conversion
A full EPS conversion requires several components working together. The electric motor itself is usually a brushless DC motor rated for continuous duty, often salvaged from a donor vehicle or purchased as an aftermarket unit. Common sources include Miata, Civic, or Accord power steering motors, though fitment varies by your car's steering column diameter and length.
The control module interprets sensor signals and manages motor speed and direction. Some aftermarket modules are programmable, letting you adjust information levels and response curves. You'll also need a wiring harness to connect the module to the motor, battery, and sensors — this is often custom-built or adapted from a donor vehicle's harness.
A steering angle sensor tells the system which direction you're turning and how far. Most modern EPS systems use a contactless magnetic sensor mounted inside the steering column. You may also need a vehicle speed sensor input so the system can reduce information at highway speeds, improving stability and steering feel.
Finally, you'll need a power source. Most EPS motors draw 40 to 80 amps at full information, so you'll run a dedicated wire from the battery through a relay and fuse to the control module. Undersizing this circuit is a common cause of conversion failure.
Installation complexity and what to expect
The physical installation — removing the old hydraulic pump and hoses, mounting the electric motor, running wiring — typically takes 20 to 40 hours depending on your vehicle's layout and your experience level. Vehicles with tight engine bays or complex steering columns take longer. You'll need basic hand tools, a multimeter, and crimpers for electrical connections.
The harder part is integration. The motor and module need to communicate with your car's existing systems, and older vehicles often lack the sensors a modern EPS system expects. You may need to add a vehicle speed sensor, wire it into the module, and tune the information curve so the steering doesn't feel numb at highway speeds or too heavy in parking lots.
Testing and tuning can take another 10 to 20 hours. You'll drive the car, feel how the steering responds at different speeds, adjust the module settings, and repeat. Getting the information curve right so it feels natural rather than artificial is the difference between a conversion that works and one that feels wrong.
Cost breakdown: parts versus labor
Parts alone typically run $1,200 to $3,500. A used EPS motor from a salvage yard costs $300 to $800. A programmable control module runs $400 to $1,200. Wiring harness, sensors, and connectors add another $200 to $500. A new steering wheel or adapter to fit the motor shaft can add $200 to $600 if your original wheel won't work.
Labor at a shop that specializes in steering conversions — usually a performance or restoration shop — runs $800 to $3,000 depending on your vehicle and how much custom work is needed. A shop unfamiliar with EPS conversions may charge more or decline the job entirely because it falls outside their normal work.
If you're doing the work yourself, you're trading time for money. Budget 30 to 60 hours of your own labor, plus the cost of any tools you don't already own. A multimeter and crimper set run $50 to $150 total. If you get stuck, hiring a specialist for a few hours of consultation costs $100 to $200 per hour.
Vehicles that benefit most from EPS conversion
Classic cars and hot rods see the biggest practical improvement. A 1970 Chevelle or 1965 Mustang with manual steering requires real physical effort, especially at low speeds or when parking. Converting to EPS cuts that effort dramatically while keeping the car's original appearance if you use a steering wheel adapter.
Older performance cars with heavy hydraulic systems also benefit. A 1980s Porsche 911 or Corvette with power steering that pulls hard on the engine and generates heat becomes noticeably easier to drive and slightly more fuel-efficient. The reduction in engine load is real enough that some owners report cooler running temperatures and slightly better mileage.
Vehicles you drive regularly — daily drivers or weekend cruisers — see more benefit than show cars that sit in a garage. The fuel economy improvement is modest on older engines, typically 1 to 3 miles per gallon, but it adds up over thousands of miles. The comfort improvement in stop-and-go traffic or long highway drives is when ready and noticeable.
Newer vehicles (1990s and later) already have EPS from the factory, so conversion makes no practical sense unless you're replacing a failed hydraulic system and want to avoid the cost of a new pump.
Common problems and how to avoid them
Undersized electrical wiring is the most common failure point. An EPS motor can draw 80 amps or more during full information, and if your battery cable, relay, or fuse is rated for less, the system will shut down or the fuse will blow repeatedly. Run at least 4-gauge wire from the battery, use a 100-amp relay, and fuse at 80 to 100 amps. This costs $50 to $100 in parts and prevents most electrical headaches.
Poor sensor integration causes steering that feels numb or overly sensitive. If the module doesn't know your vehicle speed, it can't reduce information at highway speeds, making the car feel twitchy. If the steering angle sensor is misaligned, the motor may fight your inputs. Test all sensors with a multimeter before final assembly and calibrate the module according to its manual.
Mechanical binding — where the motor or linkage catches or resists — usually means the motor isn't aligned with the steering column or the mounting bracket is slightly bent. This shows up when ready during test drives as a grinding or clicking sound. Stop and check alignment before driving further; continuing can damage the motor.
Tuning the information curve takes patience. Too much information and the steering feels artificial and unpredictable. Too little and you've gained nothing over the original system. Most programmable modules let you adjust information at different speeds. Start conservative, drive the car for a week, then make small adjustments.
Alternatives if a full conversion isn't practical
If the cost or complexity of a full EPS conversion is too high, a modern hydraulic power steering pump is a simpler upgrade for older vehicles. You keep the existing hydraulic system but replace the worn pump with a newer, more efficient one. This costs $400 to $800 in parts and labor and improves reliability without the electrical complexity.
A smaller-displacement hydraulic pump or a variable-displacement pump reduces the load on your engine compared to the original system. You won't get the fuel economy gains of full EPS, but you'll get easier steering and lower engine load. This is a good middle ground if you want to improve drivability without committing to a full conversion.
For show cars or vehicles driven rarely, upgrading the steering column bushings and replacing worn tie-rod ends often improves feel and response enough that a full conversion isn't necessary. A tighter, more responsive steering system can feel almost new without any power information changes.
Frequently Asked Questions
Will electric power steering conversion affect my car's handling or steering feel?
Properly tuned EPS should feel natural and responsive, similar to the original system but with less physical effort. Poor tuning can make steering feel numb or overly sensitive. The key is adjusting the information curve so the motor provides more help at low speeds (parking) and less at highway speeds (stability). Most drivers adapt within a few drives.
Can I use a power steering motor from a different car?
Yes, but fitment matters. Motors from similar-era vehicles with comparable steering column diameters and lengths work best. A Miata motor fits many small cars; a Civic motor works on some compact vehicles. You'll need to adapt the motor shaft to your steering wheel and may need custom brackets. Check online forums for your specific vehicle to find proven donor cars.
How much fuel economy improvement should I expect?
On older vehicles with heavy hydraulic systems, expect 1 to 3 miles per gallon improvement. The exact gain depends on how much your original pump was loading the engine and how much you drive in stop-and-go traffic versus highway. Highway driving sees less improvement because the pump wasn't working as hard anyway.
What happens if the electric motor fails after conversion?
You lose power information and the steering reverts to manual — heavy but still functional. This is safer than a hydraulic pump failure, which can leave you with no steering pressure and a locked wheel. Replacing the motor costs $300 to $800 in parts plus labor. Most EPS motors last 100,000 miles or more if properly wired and cooled.
Do I need to modify my steering wheel to fit the electric motor?
Usually yes. The motor shaft diameter may not match your original steering wheel hub. You can use a steering wheel adapter (a thick spacer that fits between the wheel and shaft), buy a new wheel that fits the motor shaft, or have a machine shop bore out your original wheel. Adapters cost $50 to $200; new wheels run $200 to $600.