What a valve clearance feeler gauge does and why you need one
A valve clearance feeler gauge is a tool that measures the gap between your engine's valve stem and the rocker arm or cam follower that operates it. This gap—called valve clearance or valve lash—must stay within a specific range for your engine to run smoothly, start reliably, and avoid damage to the valves and cylinder head.
Over time, engine parts wear. The gap grows larger, which means the valve doesn't open fully and your engine loses power and fuel economy. Or the gap shrinks, which means the valve doesn't close completely and you lose compression, get rough idle, and risk burning the valve seat. A feeler gauge lets you measure this gap yourself without special equipment, and it costs between $5 and $20.
Not all engines need regular valve clearance checks. Modern engines with hydraulic valve adjusters or overhead cam designs often adjust themselves. But older engines, many small engines (lawn mowers, generators), and some motorcycles require manual adjustment every 10,000 to 50,000 miles depending on the make and model. Check your owner's manual or service manual to see if your engine is one of them.
Key Takeaways
- Valve clearance is the gap between the valve stem and the part that opens it, and it must stay within a narrow range or your engine will lose power or suffer damage.
- A feeler gauge is a set of thin metal blades marked with thickness measurements that you slide between the valve stem and rocker arm to find the exact gap.
- You check valve clearance only when the engine is cold and the piston is at top dead center on the compression stroke for that cylinder.
- If the gap is too large or too small, you adjust it by loosening the rocker arm nut and turning an adjustment screw, then re-measure until the gauge slides through with light resistance.
- Your owner's manual or service manual lists the correct clearance for your specific engine, which varies by engine type and often differs between intake and exhaust valves.
The parts of a feeler gauge and how to read it
A feeler gauge set is a fan of thin metal blades, usually 20 to 26 blades, held together by a pivot pin at one end. Each blade is a different thickness, marked in thousandths of an inch (0.002", 0.003", 0.004", and so on) or in millimeters (0.05mm, 0.10mm, 0.15mm). The thickness is stamped or printed on each blade.
To use it, you separate the blades and select the one that matches the clearance specification in your manual. Slide that blade into the gap between the valve stem and rocker arm. The blade should fit snugly with light resistance—not so loose it falls through, not so tight you have to force it. If it slides through too easily, the gap is larger than that blade's thickness. If it won't fit, the gap is smaller.
Most mechanics carry a set with blades in increments of 0.001" or 0.002" so they can narrow down the exact gap. If your manual calls for 0.010" clearance and a 0.010" blade slides through easily but a 0.012" blade won't fit, the gap is between those two sizes and you need to adjust it.
Finding the right cylinder and positioning the engine
Valve clearance must be checked when the engine is completely cold—not warm, not running. A warm engine expands, which changes the gap and gives you a false reading. Wait at least two hours after the engine last ran, or check it first thing in the morning before starting.
You also must position the piston at top dead center (TDC) on the compression stroke for the cylinder you are checking. This is the point where the piston is at the very top of its travel and both valves for that cylinder are closed. Your service manual shows you how to find TDC for your specific engine—usually by aligning a mark on the crankshaft pulley with a mark on the engine block, or by watching the rocker arms and waiting until both stop moving for that cylinder.
Once you have TDC, you can check the intake and exhaust valves for that cylinder. Then rotate the crankshaft to the next cylinder's TDC and repeat. The order depends on your engine's firing order, which is in your manual. Some engines require you to check all cylinders; others let you check pairs at once if you position the crankshaft correctly.
Measuring the gap step by step
With the engine cold and positioned at TDC for your cylinder, locate the rocker arm or cam follower for the valve you are checking. You will see the valve stem—a small rod sticking up from the cylinder head—and the rocker arm or follower resting on top of it. The gap between them is what you measure.
Select the feeler gauge blade that matches your manual's specification. Slide it gently into the gap. It should move in with light resistance, as if you are sliding a piece of paper into a book. You should feel a slight drag but not have to push hard. If the blade slides in too easily, try the next larger size. If it won't fit, try the next smaller size. Once you find the blade that fits with the right feel, you have your measurement.
Write down the reading for each valve. Compare it to the specification in your manual. If the gap is within range (usually ±0.002" or ±0.05mm), you are done with that valve. If it is outside the range, you need to adjust it.
Adjusting the clearance when it is out of range
If the gap is too large or too small, you adjust it by loosening the rocker arm and turning an adjustment screw. The exact method varies by engine design, so your service manual is essential here—some engines have a locknut and adjustment screw on the rocker arm itself, others have a screw on the pushrod or a cam follower adjustment.
The general process is: loosen the locknut a half turn, turn the adjustment screw clockwise to decrease the gap (make it smaller) or counterclockwise to increase it (make it larger), then re-measure with the feeler gauge. Make small turns—a quarter turn of the screw often changes the gap by 0.002" to 0.004". Once the gauge fits with light resistance, hold the adjustment screw steady and tighten the locknut, then measure again to make sure the adjustment did not shift.
If you turn the screw and the gap does not change, or if it changes too much, stop and consult your manual or a mechanic. You may have the wrong screw, or the rocker arm may be worn and need replacement.
Common mistakes and how to avoid them
The most common mistake is checking clearance on a warm engine. Heat expands the metal, so the gap appears larger than it really is. You will adjust it smaller, then when the engine cools it will be too tight. Always wait for the engine to cool completely.
Another mistake is not positioning the engine at TDC. If the piston is partway through its stroke, the valve stem will be partially open and you will not get an accurate reading. Take time to find TDC correctly using your manual's method.
A third mistake is using the wrong clearance specification. Intake and exhaust valves often have different gaps, and different engine models vary widely. Check your manual, not a neighbor's engine or an online forum. If you cannot find your manual, search for it by engine model number—most manufacturers post them free online.
Finally, do not force the feeler gauge. If it will not slide in, the gap is smaller than that blade. Forcing it can bend the blade or damage the valve stem. Try a smaller blade instead.
When to check valve clearance and what to do if you find a problem
Check valve clearance at the intervals listed in your owner's manual, or if you notice rough idle, loss of power, hard starting, or a ticking noise from the cylinder head. A ticking that gets faster as the engine warms up often means the clearance is too large.
If you find that the clearance is out of range and you adjust it back into range, the problem is solved and you can drive normally. If you find that the clearance is way out of range—for example, 0.020" when it should be 0.010"—or if it goes out of range again after a few hundred miles, something is wearing faster than normal. This could mean a worn rocker arm, a bent pushrod, or a valve seat that is receding. Have a mechanic inspect the cylinder head.
If you are not comfortable doing this work yourself, a shop can check and adjust valve clearance in an hour or two for a reasonable cost. It is not a complicated job, but it does require patience and attention to detail.
Frequently Asked Questions
Do I need a feeler gauge if my car is newer than 2000?
Most cars built after 1990 have hydraulic valve adjusters that maintain clearance automatically, so you do not need to check it. Check your owner's manual to be sure. Older cars, motorcycles, lawn mowers, and small engines usually do need manual checks.
What if I cannot find the exact clearance specification in my manual?
Search online for your engine's model number and "valve clearance" or "valve lash." Most manufacturers publish service manuals free on their websites. If you still cannot find it, a local shop can tell you the spec in one phone call.
Can I check valve clearance while the engine is running?
No. A running engine is dangerous and the heat changes the gap. Always stop the engine, wait for it to cool, and position it at TDC before measuring.
What does it mean if the feeler gauge blade bends when I slide it in?
It means the gap is much smaller than that blade's thickness—the valve is nearly or completely closed. Stop when ready and try a much smaller blade. If even a 0.001" blade will not fit, the valve may be stuck or the clearance may be zero or negative, which requires professional inspection.
How often should I check valve clearance?
Check at the interval listed in your owner's manual, which is usually every 10,000 to 50,000 miles for engines that require it. Some older engines need it every season if they sit unused. If you notice symptoms like rough idle or ticking, check it sooner.