A track chainring adapter lets you swap chainrings on a fixed-gear or single-speed bike without removing the crank arm
A track chainring adapter is a threaded collar that screws onto the crank spindle between the crank arm and the chainring. Instead of unbolting the chainring from the crank arm itself—which requires removing the crank arm, the bottom bracket, or both—you unscrew the adapter, slide off the old chainring, and bolt on a new one. The adapter stays in place on the spindle.
This matters because fixed-gear and single-speed bikes use chainrings that bolt directly to the crank arm, not to a cassette or freewheel. When you want to change your gearing ratio—to go faster on flat ground or climb hills more easily—you have to change the chainring itself. Without an adapter, that job takes 20 minutes and a crank puller. With one, it takes 5 minutes and a wrench.
Track adapters are standard equipment on velodrome bikes, where riders change gearing between races. They are also common on commuter fixed-gears and single-speeds, where the same bike might need different ratios for different seasons or routes.
Key Takeaways
- A track chainring adapter screws onto the crank spindle and holds the chainring in place, so you can remove and replace the chainring without touching the crank arm.
- Track adapters come in different thread sizes and pitches depending on your crank spindle diameter, so you must measure your spindle before buying.
- The adapter itself costs between $15 and $40, but saves you the time and tools needed to remove a crank arm or bottom bracket.
- Not all chainrings fit all adapters; the bolt circle diameter (BCD) of the chainring must match the adapter's mounting pattern.
How a track chainring adapter sits on the crank spindle
The crank spindle is the axle that runs through the bottom bracket and holds both crank arms. On a fixed-gear or single-speed bike, the chainring bolts to the right crank arm using four or five bolts that pass through the chainring and into threaded holes in the crank arm itself.
A track adapter screws onto the spindle just outboard of the right crank arm. The chainring then bolts to the adapter instead of to the crank arm. When you want to change chainrings, you unscrew the adapter from the spindle, remove the four or five bolts holding the chainring to the adapter, slide the old chainring off, bolt on the new one, and screw the adapter back onto the spindle. The crank arm never moves.
The adapter is held in place by friction and by the bolt tension of the chainring itself. As long as the adapter is screwed on hand-tight and the chainring bolts are torqued evenly, the adapter will not rotate or loosen during riding.
Measuring your crank spindle to find the right adapter
Track adapters are threaded to fit specific spindle diameters and thread pitches. The most common sizes are 1.37 inches × 24 threads per inch (TPI), which fits most modern track cranks and many fixed-gear cranks. Older or imported cranks may use 1.37 × 20 TPI, 1.3 × 24 TPI, or other sizes.
To measure your spindle, remove the right crank arm or look at the exposed spindle just outboard of the arm. Measure the diameter with calipers or a ruler. If you cannot measure it directly, look up your crank model online or ask at a bike shop. Buying the wrong thread size means the adapter will not screw on or will screw on but not hold tight.
Some adapters are adjustable or come in multiple sizes, but most are fixed. Write down your spindle size before shopping, and confirm the adapter's thread size matches before you buy.
Chainring bolt circle diameter (BCD) and compatibility
The chainring bolts to the adapter using four or five bolts arranged in a circle. The diameter of that circle is called the bolt circle diameter, or BCD. Common BCD sizes for track and fixed-gear chainrings are 104 mm (four bolts), 110 mm (five bolts), and 130 mm (five bolts).
Your adapter has a fixed BCD. If your chainring's BCD does not match the adapter's BCD, the bolt holes will not line up and you cannot mount the chainring. Before you buy a new chainring, check the BCD of both your adapter and the chainring you want to use.
Most track adapters come with a BCD of 110 mm or 130 mm, which covers most fixed-gear and track chainrings. If you have an older or unusual crank, the BCD may be different. Check your current chainring's BCD by counting the bolts and measuring the distance between the centers of two bolts directly across from each other.
Installing a track chainring adapter on your crank
Before you install an adapter, make sure your crank spindle is clean and dry. Dirt or grease can prevent the adapter from screwing on evenly or can cause it to loosen during riding.
Screw the adapter onto the spindle by hand until it is snug. Do not use a wrench or tool; hand-tight is enough. If the adapter is hard to turn, stop and check that the thread size is correct. Forcing a wrong-sized adapter onto the spindle will strip the threads.
Once the adapter is on, bolt your chainring to it using the four or five bolts that came with the chainring or adapter. Tighten the bolts in a star pattern—tighten one bolt, then skip to the bolt across from it, then tighten the next bolt, and so on. This keeps the chainring centered and prevents it from tilting. Tighten each bolt a little at a time until they are all snug, then do a final pass to make sure none have loosened.
After you have ridden for a few miles, stop and check that the chainring bolts are still tight. Vibration can loosen bolts during the first ride. If any bolt has backed out, tighten it again.
When to use a track adapter versus removing the crank arm
A track adapter is worth using if you change chainrings more than once or twice a year. If you change gearing seasonally or swap between a climbing gear and a racing gear, an adapter saves you time and eliminates the need for a crank puller and bottom bracket tools.
If you change chainrings rarely or never, an adapter is not necessary. You can remove the crank arm and change the chainring directly if you have the tools and the time. An adapter is also not useful if your bike has a cassette or freewheel, because those bikes do not use chainring adapters.
Some riders use an adapter as a backup: they keep the adapter on the spindle all the time, so if a chainring breaks or wears out, they can swap it quickly without going to a shop. Others install an adapter only when they know they will be changing chainrings soon.
Common problems and how to avoid them
The most common problem is buying an adapter with the wrong thread size. The adapter will not screw on, or it will screw on but feel loose or cross-threaded. Always measure your spindle and confirm the thread size before you buy.
Another problem is the chainring bolts loosening during riding. This happens if the bolts are not tightened evenly or if the adapter itself is not screwed on tight enough. Tighten the bolts in a star pattern and check them again after your first ride.
A third problem is the adapter rotating on the spindle. This is rare if the adapter is screwed on hand-tight and the chainring bolts are tight, but it can happen if the spindle is dirty or if the adapter's threads are worn. Clean the spindle before installing the adapter, and replace the adapter if it spins freely on the spindle.
Frequently Asked Questions
Can I use a track adapter on any fixed-gear bike?
Only if your crank spindle has the right thread size. Most modern track and fixed-gear cranks use 1.37 × 24 TPI, but older or imported cranks may use different sizes. Measure your spindle before buying an adapter.
What is the difference between a track adapter and a cog adapter?
A track adapter holds a chainring on the front crank spindle. A cog adapter holds a sprocket on the rear wheel hub. They are different parts for different purposes and are not interchangeable.
Do I need special tools to install a track adapter?
No. You need a wrench to tighten the chainring bolts, but the adapter itself screws on by hand. A crank puller or bottom bracket tools are not needed.
Can I use a track adapter with a chainring that has a different BCD than my current chainring?
No. The bolt holes on the chainring must match the bolt holes on the adapter. If the BCD does not match, the chainring will not bolt on. Check the BCD of both the adapter and the chainring before you buy.
How tight should I screw the adapter onto the spindle?
Hand-tight is enough. Do not use a wrench or tool to force it on. If the adapter is hard to turn, the thread size may be wrong. Stop and check before you continue.