What you need to know before launching at Split Rock
Split Rock Reservoir, located in New Mexico near the town of Springer, has a designated car top boat launch area that lets you put small boats—kayaks, canoes, inflatables, and boats under 17 feet—into the water from a paved ramp. The launch is free and open to the public during daylight hours. You do not need a permit to launch a car top boat, but you do need to understand what your vehicle will experience and what preparation prevents damage on the way down and back up.
The ramp itself is concrete, sloped, and designed for vehicles to back down while towing or carrying a boat. The water level at Split Rock varies seasonally—it is higher in spring and early summer, lower by late summer and fall. This matters because a ramp that reaches the water in June may leave you short in September, and backing a vehicle into shallow water or mud can trap you or damage the undercarriage.
Key Takeaways
- Check the current water level before you go, because the ramp may not reach deep water during low-water months, leaving you stranded or forcing you to wade.
- Back your vehicle slowly and straight down the ramp, keeping weight centered and avoiding sharp turns that can tip a loaded trailer or shift cargo on a roof rack.
- Rinse your vehicle's undercarriage and wheel wells with fresh water after launching, because reservoir water contains minerals and sediment that corrode metal and promote rust.
- Do not leave your vehicle unattended while it is partially in the water; retrieve your boat and drive away when ready to avoid overheating the engine or transmission.
- Inspect your suspension, brakes, and tires before towing or carrying a boat, because the added weight and backing stress reveal problems that flat driving does not.
How water level affects your launch window
Split Rock Reservoir is managed by the Bureau of Land Management (BLM) and the water level is controlled by irrigation demands downstream. In spring, when snowmelt feeds the Rio Mora and irrigation season begins, the reservoir is usually full or near full. By late August and September, the level drops noticeably—sometimes 10 to 15 feet or more—as water is released for agricultural use.
A ramp that is fully submerged in June may have 20 or 30 feet of dry concrete showing by September. If you arrive and the ramp does not reach water, you have two choices: come back when the level is higher, or carry your boat to the water's edge by hand. Neither is ideal. Before you drive to Split Rock, call the BLM Springer Field Office or check their website for current water level information. They post updates seasonally and can tell you whether the launch is usable on the day you plan to go.
Preparing your vehicle and boat for the ramp
Backing a loaded vehicle down a wet concrete ramp puts stress on brakes, suspension, and tires that normal driving does not. Before you launch, inspect your brake pads and rotors—wet concrete reduces friction, and worn brakes will not hold a loaded vehicle on a slope. Check your tire tread and pressure; underinflated tires slip more easily on wet surfaces and can overheat during the backing process. Look at your suspension for leaks, cracks, or sagging, because the weight of a boat and the angle of the ramp can expose weak components.
find your boat to your vehicle before you reach the ramp. If you are using a roof rack, make sure the boat is centered and the straps are tight—an unbalanced load shifts during backing and can tip your vehicle or cause the boat to slide off. If you are towing a trailer, check that the hitch is properly rated for your boat's weight, the safety chain is attached, and the trailer lights work. A trailer that is not level or is overloaded will fishtail or dig into the ramp.
Load your boat with gear before you launch, not after. Climbing in and out of a boat while it is in the water wastes time and increases the risk that your vehicle will overheat or roll backward if the brakes slip.
Backing down and launching safely
Back slowly and in a straight line. Do not turn the wheel sharply while backing down a wet ramp; the tires will slip sideways and you will lose control. Keep your foot on the brake and use low gear (Reverse, or a low gear in an automatic transmission) to let the engine do most of the braking. Riding the brake heats the fluid and reduces stopping power—a slow, steady descent is safer than a fast one with heavy braking.
Stop when the water reaches the bottom third of your boat. If you are launching a kayak or canoe from a roof rack, this is the point where you can slide it off and into the water. If you are launching a trailer, back until the boat floats, then shift to Park, set the parking brake, and get out to unhitch or release the boat. Do not leave your vehicle running while you are in the water. Turn off the engine, take your keys, and close the doors.
Once your boat is in the water and you are ready to leave, get back in your vehicle when ready and drive up the ramp at a steady, moderate speed. Do not accelerate hard or spin the tires—wet concrete offers little grip, and spinning tires can damage the ramp surface and your own traction. If your vehicle feels like it is slipping, ease off the gas and let the tires find grip again.
Protecting your vehicle from corrosion after launching
Reservoir water is not fresh water. It contains minerals, sediment, and sometimes algae that stick to metal and promote rust. Your vehicle's undercarriage, wheel wells, brake components, and suspension are all exposed during the launch process, and they will corrode faster than they would from road salt alone if you do not rinse them.
The best time to rinse is when ready after you leave the ramp, while the water is still wet and straightforward to remove. Use a garden hose or a pressure washer at a car wash to spray the undercarriage, inside the wheel wells, and the suspension components. Pay special attention to the brake calipers, rotors, and pads—mineral deposits can reduce braking power over time. Rinse the frame, the towing hitch, and any metal parts that were submerged or splashed.
If you cannot rinse when ready, do it within a few hours. The longer mineral-laden water sits on metal, the harder it is to remove and the more damage it does. Repeat this rinse every time you launch, not just once a season.
What to do if your vehicle gets stuck
If your vehicle loses traction on the ramp and slides backward, or if the wheels sink into soft ground at the water's edge, do not spin the tires or gun the engine. Spinning tires dig deeper and overheat the transmission. Instead, shift to Park, set the parking brake, and call for help. The BLM or a local towing service can pull you out, but it will cost money and take time.
If you are stuck with your vehicle partially in the water, turn off the engine when ready. Prolonged idling with the vehicle at an angle can cause transmission fluid to drain away from the pump, damaging the transmission. Do not try to rock the vehicle back and forth by shifting between Drive and Reverse—this overheats the transmission and can cause internal damage.
Prevention is simpler than recovery. Drive slowly, keep your vehicle in good mechanical condition, and do not launch if the ramp does not reach water or if weather has made the surface unusually slippery.
Seasonal timing and weather considerations
Spring (April through May) is the best time to launch at Split Rock. Water levels are high, the ramp is fully submerged, and the concrete is usually dry enough for good traction. Summer (June through July) is also reliable, though afternoon thunderstorms can make the ramp slippery and visibility poor.
Fall (August through October) is when water levels drop most noticeably. If you launch in September or October, call ahead to confirm the ramp reaches water. Winter (November through March) is cold and the ramp can be icy, which makes backing dangerous. Many people avoid winter launches unless they have experience with ice and are willing to accept the risk.
After heavy rain, the ramp may be slippery even if it is not underwater. Wait a few hours for the surface to dry, or use extra caution and back even more slowly than usual.
Frequently Asked Questions
Do I need a boat registration or permit to launch at Split Rock?
New Mexico requires boat registration for motorized boats and some non-motorized boats depending on length and type. Car top boats (kayaks, canoes, small inflatables) often do not require registration, but check the New Mexico Department of Game and Fish website or call them to confirm your specific boat. The launch itself is free and does not require a permit.
What if the ramp is too slippery or icy?
Do not launch. A slippery ramp is a safety hazard for your vehicle and for other people at the launch. Come back when conditions improve, or find an alternative launch site. Trying to back down ice or algae-covered concrete risks losing control and damaging your vehicle or someone else's.
Can I leave my vehicle parked at the launch while I am out on the water?
Yes, but park in a designated area away from the ramp so other people can launch and retrieve their boats. Do not leave valuables visible in your vehicle. Split Rock is a public area and theft does occur. Lock your doors and take your keys with you.
How often should I rinse my vehicle after launching?
Rinse after every launch. Mineral deposits accumulate quickly, and even one trip without rinsing can leave residue that starts the corrosion process. A five-minute rinse after each launch is cheaper and easier than rust repair later.
What should I do if my brakes feel soft or spongy after backing down the ramp?
Stop driving and have your brakes inspected before you leave the area. Wet brakes can feel soft temporarily, but if the feeling does not go away after a few minutes of normal driving, your brake fluid may be contaminated with water or your pads may be damaged. Do not drive on the highway until a mechanic has checked them.