Aluminum heads cost more upfront but save weight and run cooler than cast iron
Small block Chevy aluminum cylinder heads typically cost between $800 and $3,000 per pair, depending on the brand, whether they're new or used, and how much porting work has been done. Cast iron heads for the same engine run $200 to $800 per pair. The aluminum versions weigh 40 to 50 pounds less per pair, dissipate heat faster, and allow higher compression ratios without detonation — but they require more careful maintenance and machine work if you rebuild them.
Whether aluminum heads make financial sense depends on what you're building. A street car that sees occasional track days benefits from the weight savings and cooling. A daily driver that rarely sees boost doesn't need them. A dedicated race engine or a heavily modified street engine often justifies the cost because the performance gains compound with other upgrades.
Key Takeaways
- Aluminum heads cost $800 to $3,000 per pair new; cast iron runs $200 to $800, so budget the difference into your total engine build.
- Aluminum dissipates heat roughly 25 percent faster than cast iron, which matters if you're running higher boost, compression, or ambient temperatures.
- Aluminum requires valve seat inserts and more careful torque procedures during assembly, so factor in machine shop costs if you're rebuilding.
- Used aluminum heads are common and cheaper but need pressure testing and valve seat inspection before installation.
- Popular brands include Edelbrock, Trick Flow, and World Products; each has different port shapes that affect intake manifold compatibility.
How aluminum heads perform differently from cast iron
Aluminum conducts heat roughly three times faster than cast iron, which means coolant flows through the head more efficiently and combustion chamber temperatures stay lower. That lower temperature lets you run higher compression ratios or boost without hitting detonation. A small block Chevy with aluminum heads can safely run 11:1 compression on pump gas; the same engine with cast iron heads typically maxes out around 9.5:1 before pinging under load.
The weight difference is real but often overstated. A pair of aluminum heads weighs 35 to 45 pounds; cast iron weighs 80 to 95 pounds. On a full car, that's noticeable in acceleration and braking feel, especially in a lightweight chassis. On a 3,500-pound street car, the difference is measurable but not transformative. On a 2,200-pound race car, it matters more.
Aluminum also expands and contracts more than cast iron when temperature changes. That's why aluminum heads require a specific torque sequence and often need retorquing after the first heat cycle. Cast iron is more forgiving in this regard.
Common aluminum head options for small block Chevy
Edelbrock Performer RPM heads are the entry point: around $1,200 to $1,600 per pair new, with decent flow numbers and a port shape that works with most intake manifolds. They're commonly found used for $600 to $900. Trick Flow heads run $1,800 to $2,400 new and flow better at higher valve lifts, making them popular for engines over 400 horsepower. World Products Motown heads are in the $1,400 to $1,900 range and split the difference on flow and price.
Brodix and AFR make premium heads that exceed $2,500 per pair and are typically reserved for race engines or high-end street builds. Used examples of any brand are worth considering if you can inspect them in person or have a machine shop pressure test them before purchase.
Port shape matters: Edelbrock and Trick Flow heads have different intake port angles, so swapping between them may require a different intake manifold. Check compatibility before buying. Casting quality varies by year and brand; heads cast in the 1990s and early 2000s are generally more consistent than older stock castings.
Machine work and assembly costs you need to budget
If you're rebuilding aluminum heads, expect $400 to $800 per pair for valve seat inserts, new valve guides, and a full cleanup and inspection. Cast iron heads need similar work but are cheaper to machine because the material is easier to cut. Aluminum also requires careful honing of the valve seats because the material is softer and wears faster.
Assembly requires a torque wrench and a specific sequence. Most aluminum heads use a three-step torque pattern: typically 25 foot-pounds, then 50, then a final pass to 65 foot-pounds. Skipping steps or torquing in random order can warp the head or crack the casting. If you're not comfortable with this, a machine shop will assemble them for $150 to $300 per pair.
Gasket selection matters more with aluminum. Use a quality multi-layer steel gasket designed for aluminum heads; cheap gaskets fail faster because aluminum expands differently than the gasket material. Expect to spend $40 to $80 on head gaskets instead of $15 to $25 for cast iron.
Cooling system changes when you switch to aluminum
Aluminum heads dissipate heat faster, which means your coolant temperature may drop 10 to 15 degrees under load compared to cast iron. That's usually good — it reduces detonation risk and extends engine life. But if your cooling system is marginal, the faster heat rejection can expose other problems like a weak water pump or a radiator that's too small.
Some builders add a small electric fan or upgrade the water pump when switching to aluminum heads, especially on older cars with original cooling systems. The cost is $200 to $600 for a quality electric fan kit. If your current system keeps coolant below 210 degrees with cast iron heads, aluminum heads alone won't require upgrades.
Intake manifold compatibility and port matching
Aluminum heads have different intake port shapes depending on the manufacturer. Edelbrock Performer RPM ports are taller and narrower than Trick Flow ports. If you buy a used intake manifold designed for one brand and bolt it to heads from another, you'll have a mismatch that reduces flow and creates vacuum leaks.
Before buying aluminum heads, confirm that your intake manifold is compatible. If you're starting from scratch, buy the heads first, then source an intake manifold designed for that specific head. A quality aluminum intake manifold runs $400 to $800 new; used ones are $200 to $400. Mismatched combinations cost you 10 to 20 horsepower and fuel economy.
Used aluminum heads: what to check before buying
Used aluminum heads are common because many builders upgrade or swap engines. Before buying, have a machine shop pressure test them for cracks — this costs $50 to $100 and is non-negotiable. Aluminum cracks are invisible to the eye but will leak coolant or oil once installed.
Inspect the valve seats for pitting or erosion. If the previous owner ran them without proper cooling or detonated, the seats may be damaged. Ask the seller whether the heads have been rebuilt, how many miles they have, and what engine they came from. Heads from a 350 small block are the same casting as heads from a 383, but heads from a 400 small block have different port shapes and won't bolt on without modification.
Check the intake and exhaust ports for cracks or casting defects. Look at the combustion chambers for carbon buildup, which is normal, but also for erosion or pitting, which suggests the engine ran hot or detonated. A used pair in good condition should cost $400 to $700; anything cheaper may have hidden damage.
Frequently Asked Questions
Can I bolt aluminum heads onto my existing small block Chevy engine?
Yes, if the engine is a 262, 283, 305, 327, or 350 small block. The bolt pattern is the same. You'll need new head gaskets, new intake and exhaust manifolds may be required depending on port shapes, and you should have the block deck checked for flatness before assembly. A 400 small block has a different bolt pattern and won't work without modification.
Do aluminum heads need a special coolant?
No, but use a coolant that's compatible with aluminum — most modern long-life coolants are. Avoid old-style green coolant if you're mixing aluminum and cast iron parts, because it can cause galvanic corrosion. Use either all aluminum-compatible coolant or stick with one type throughout the system.
How much horsepower do aluminum heads add compared to cast iron?
On a stock small block, aluminum heads add 15 to 25 horsepower through better cooling and slightly improved flow. On a modified engine with a performance cam and intake, the gain is 20 to 40 horsepower because the better cooling allows higher compression or boost. The exact number depends on what else is in the engine.
Are aluminum heads worth it for a street car that doesn't see the track?
If your car runs stock compression and boost, cast iron heads are fine and save you $600 to $1,200. If you're adding a supercharger, turbo, or higher compression, aluminum heads pay for themselves through better reliability and detonation margin. For a mild street engine, they're a luxury, not a necessity.
What's the difference between new and used aluminum heads?
New heads come with a warranty and known history; used heads are cheaper but require pressure testing and inspection. A used pair in good condition costs 40 to 50 percent less than new. The risk is hidden cracks or worn valve seats. If you buy used, budget $50 to $100 for pressure testing and $200 to $400 for valve seat work if needed.