What small block Chevrolet valve covers are and why they matter
A valve cover is a metal or plastic lid that sits on top of your engine's cylinder head and seals the valve train — the moving parts that control when fuel and air enter and exit each cylinder. On a small block Chevrolet (the 262, 283, 305, 327, 350, and 400 cubic-inch engines), the valve cover keeps oil inside the engine and dirt out. Over time, the rubber gasket underneath hardens and cracks, oil seeps onto the engine block, and you may smell burning oil or see stains on your driveway.
Replacing a valve cover gasket is one of the most common maintenance tasks on these engines because the gasket fails faster than other engine seals. The job itself is straightforward — you unbolt the cover, scrape off the old gasket, install a new one, and bolt it back down — but choosing the right cover and gasket combination matters. A poor seal will leak again within months. A cover that does not fit your specific engine year or accessory setup will either not bolt down or interfere with other components.
Key Takeaways
- Small block Chevrolet valve covers come in stamped steel (original style), cast aluminum, and plastic, each with different fitment and appearance characteristics.
- The year, engine displacement, and whether your engine has emissions equipment or aftermarket accessories determine which cover will fit without modification.
- Gasket material — cork, rubber, or silicone — affects how long the seal lasts and how much heat it can withstand.
- Covers designed for one generation of small block may not bolt to another without drilling new holes or using adapter plates.
Stamped steel covers versus aluminum and plastic options
Original small block Chevrolet valve covers were stamped steel — thin metal pressed into shape and painted. They are light, inexpensive, and look correct on a stock engine. The downside is that they rust easily, dent if you bump them, and the mounting ears can crack if you over-tighten the bolts. If you are restoring a car to original appearance or keeping costs low, stamped steel is the standard choice.
Cast aluminum covers are heavier and more durable. They do not rust, they dissipate heat better than steel, and they look more finished on a modified engine. The trade-off is cost — aluminum covers run two to three times the price of steel — and fitment. Aluminum covers from different manufacturers have different bolt hole patterns and heights, so you cannot assume one will fit another engine or year without checking dimensions first.
Plastic covers are lightweight and cheap, but they crack in the sun and under high heat. Most shops and enthusiasts avoid them unless the engine is lightly used or the budget is very tight. Plastic covers are common on newer engines but less common as replacements for classic small blocks.
How engine year and displacement affect valve cover fitment
Small block Chevrolet engines from 1955 to 1979 share the same basic cylinder head design, but valve cover mounting changed several times. Early engines (1955–1962) used a different bolt pattern than mid-year engines (1963–1979). If you install a 1970s cover on a 1957 engine, the bolt holes will not line up.
Displacement — 262, 283, 305, 327, 350, or 400 cubic inches — does not usually affect valve cover fitment by itself. What matters is the year the head was cast and whether the engine has emissions equipment bolted to it. A 1972 350 and a 1972 305 will use the same valve cover, but a 1972 350 with an air pump will need a cover with a cutout or clearance for the pump bracket, while a 1970 350 without emissions equipment will not.
Before ordering a replacement cover, note your engine's year (stamped on the block or head), the cubic-inch displacement, and whether you see an air pump, smog pump, or other emissions hardware bolted to the head or block. Provide this information to the supplier — guessing will lead to a cover that does not fit.
Gasket materials and how long they last
Cork gaskets were original equipment on most small block Chevrolets through the 1970s. Cork is porous and absorbs oil, which keeps it soft and pliable. The downside is that cork hardens and shrinks over 10 to 15 years, especially if the engine runs hot. Once a cork gasket fails, it almost never re-seals — you have to replace it.
Rubber gaskets (usually neoprene or nitrile) are tougher than cork and last longer in high-heat conditions. They are less likely to shrink, and some can be re-used if removed carefully. Rubber gaskets are the most common replacement choice for engines that see regular use or run warm.
Silicone gaskets are the newest option and can withstand the highest temperatures. They are often used on modified engines with headers, high-output ignition systems, or engines that run in hot climates. Silicone is more expensive than rubber but can last 20 years or more. The trade-off is that silicone is messier to install — it requires a clean surface and careful torque control, and it can squeeze out from under the cover if over-tightened.
Checking your current valve cover for reuse
If your valve cover is not cracked, dented, or rusted through, you may be able to keep it and replace only the gasket. Remove the cover by unbolting it — usually four to six bolts around the perimeter — and inspect the sealing surface where the gasket sits. Run your finger along the edge. If it is smooth and flat, the cover is reusable. If you feel pitting, corrosion, or warping, the cover itself is leaking and needs replacement.
Check the bolt holes for stripped threads or cracks radiating from the holes. If the holes are damaged, you can drill them out and use larger bolts with washers, or you can replace the cover. Many people replace both the cover and gasket at the same time to avoid a second job in a few years.
Installation steps and common mistakes
Remove the old valve cover by unbolting it and carefully prying it off with a plastic scraper or old credit card — do not use a metal tool that can gouge the sealing surface. Scrape away all old gasket material and any corrosion from the sealing surface on both the cover and the cylinder head. Wipe the surface clean with a rag and let it dry.
If you are using a cork or rubber gasket, lay it in the groove or on the sealing surface of the cover. If you are using a silicone gasket, explore a thin bead of silicone sealant to the sealing surface of the head, then press the gasket into place. Do not use sealant with cork or rubber gaskets unless the manufacturer specifies it.
Install the cover and hand-tighten all bolts first. Then tighten in a crisscross pattern (like tightening wheel lugs) to may support even pressure. Tighten to 3 to 5 foot-pounds — snug but not hard. Over-tightening crushes the gasket and can crack the cover or strip the bolt holes. Start the engine and check for leaks after 10 minutes of running.
Aftermarket covers and modifications
If you are building a modified engine or swapping a small block into a different car, you may need a valve cover that does not match the original. Tall-deck covers are designed for engines with higher cylinder heads. Finned aluminum covers improve cooling and look aggressive. Breather-equipped covers have a built-in vent for crankcase pressure.
Before buying an aftermarket cover, measure the distance from the bolt holes to the edge of the head, and check the height of any accessories (intake manifold, alternator, headers) that might interfere. Many custom covers require drilling new bolt holes or using spacers. Some shops sell adapter plates that allow you to use a cover designed for a different engine or year — these are useful if you have a specific look in mind but fitment is tight.
Frequently Asked Questions
Can I use a valve cover from a different year small block Chevrolet?
Sometimes, but not always. Covers from 1963–1979 often interchange, but 1955–1962 covers use a different bolt pattern. Check the bolt hole spacing and count before ordering. If the holes do not line up, you will need an adapter plate or a cover designed for your specific year.
What does it mean if oil is leaking from under the valve cover?
The gasket has failed and is no longer sealing. Oil seeps past the gasket and runs down the outside of the engine. You need to replace the gasket, and possibly the cover if the sealing surface is damaged or corroded. A small amount of seepage is normal on very old engines, but steady dripping means the gasket is done.
How tight should I tighten the valve cover bolts?
Tighten to 3 to 5 foot-pounds in a crisscross pattern. This is snug enough to compress the gasket without crushing it. Over-tightening is the most common mistake — it crushes the gasket, cracks the cover, and strips the bolt holes. If you do not have a torque wrench, tighten until snug and stop.
Do I need to use sealant with a new gasket?
Cork and rubber gaskets do not need sealant unless the manufacturer says otherwise. Silicone gaskets usually require a thin bead of silicone sealant on the sealing surface. Check the gasket package or ask the supplier before installation.
Why does my new valve cover still leak after I replaced the gasket?
The most common cause is an unclean sealing surface — old gasket material or corrosion prevents the new gasket from sealing. The second cause is over-tightening, which crushes the gasket. The third is a warped cover or head, which requires resurfacing or replacement. Clean the surface thoroughly, use the correct gasket material for your engine, and tighten to spec.