What the Kenwood Excelon DMX1057XR does and whether it fits your xB

The Kenwood Excelon DMX1057XR is a 6.75-inch touchscreen car stereo that replaces your factory head unit — the radio and control panel mounted in your dashboard. It plays AM/FM radio, Bluetooth audio, USB files, and Apple CarPlay or Android Auto depending on your phone. The screen is larger than most factory units, which means it sits flush in the xB's dashboard opening without requiring a custom mounting bracket.

This head unit fits 2004–2015 Scion xB models without modification to the dashboard itself. The xB's factory opening is a single-DIN size (the standard rectangular slot for aftermarket stereos), and the DMX1057XR's trim ring matches that opening. You will need a wiring harness adapter specific to your xB's year and a dash kit if you want a finished look around the edges, but no cutting or drilling is required.

The DMX1057XR is a mid-range Kenwood product, positioned between basic single-DIN units and higher-end models. It includes features like backup camera input, steering wheel control compatibility, and a built-in amplifier, but does not have features like Apple CarPlay wireless connectivity or advanced sound tuning that pricier models offer.

Key Takeaways

  • The DMX1057XR is a 6.75-inch touchscreen stereo that replaces your factory head unit and fits the xB without dashboard modification.
  • You will need a wiring harness adapter matched to your xB's year, a dash kit for a finished appearance, and a backup camera module if you want to use the backup camera input.
  • Installation requires disconnecting the factory stereo, running new wiring behind the dashboard, and securing the new unit in the opening — a task most people can do with basic tools in two to four hours.
  • The unit supports Bluetooth audio, USB playback, Apple CarPlay, and Android Auto, but wireless CarPlay requires a separate adapter module.
  • Steering wheel controls on your xB can be retained with a compatible interface module, which prevents you from losing volume and track buttons during the swap.

Wiring and adapter requirements for your xB model year

The xB's electrical system changed between the first generation (2004–2006) and second generation (2008–2015), so your wiring harness must match your specific year. A wiring harness adapter connects the factory wiring behind your dashboard to the new stereo's harness, eliminating the need to cut and splice wires. Metra and Scosche both make xB-specific adapters; confirm your year before ordering because using the wrong generation adapter will result in non-functioning features or a stereo that does not power on.

The DMX1057XR also requires a power cable run to the battery and a ground cable to bare metal on the chassis. These are not part of the factory wiring and must be installed separately. The power cable should be 4-gauge or thicker and run through the firewall (the metal wall between the engine bay and cabin) using a grommet to protect the insulation. The ground cable can be bolted to any unpainted metal surface on the vehicle frame, typically under the rear seat or behind the kick panel.

If your xB has a factory backup camera or if you plan to add one, the DMX1057XR has a dedicated camera input. You will need a backup camera module designed for your xB's year if the factory system exists, or a standalone camera and harness if you are installing one from scratch. The camera signal runs separately from the main wiring harness.

Dash kit and trim ring options

A dash kit is a plastic frame that fills the gap between the new stereo and the edges of the dashboard opening. Without it, you will see bare dashboard plastic around the unit. For the xB, Metra and Scosche both offer kits that match the factory dashboard color and texture. The kit is not required for the stereo to function, but it makes the installation look professional and prevents dust from entering the gap.

The DMX1057XR comes with a trim ring that fits the stereo's bezel. The dash kit and trim ring work together: the kit mounts to the dashboard, and the stereo slides into the kit with the trim ring visible. Installation of the kit itself takes 15 to 30 minutes and requires no tools beyond a plastic trim removal tool to avoid scratching the dashboard.

Some installers skip the dash kit if they plan to use the stereo temporarily or want to minimize cost. This is a personal choice, but the gap left behind can collect dust and looks unfinished. If you are selling the xB later, a finished installation with a dash kit will appeal to more buyers than a bare opening.

Steering wheel control retention and compatibility

The xB's steering wheel has volume and track-skip buttons integrated into the factory stereo system. When you remove the factory head unit, those buttons stop working unless you install a steering wheel control interface module. Metra and PAC both make modules that decode the factory button signals and send them to the DMX1057XR, restoring full steering wheel control without any modification to the wheel itself.

The interface module plugs into the factory wiring harness and the new stereo's wiring harness simultaneously. It costs between $25 and $50 and takes five minutes to install. Without it, you will have to reach the touchscreen to adjust volume or skip tracks, which is unsafe while driving. If you use your steering wheel controls frequently, this module is worth the small cost and effort.

Some aftermarket stereos do not support steering wheel control inputs at all, but the DMX1057XR does, so as long as you have the right interface module for your xB's year, the buttons will work exactly as they did before.

Installation steps and tools you will need

Installation requires a car stereo removal tool (a flat metal tool that pops the factory head unit out of the dashboard), a screwdriver set, a wire stripper and crimper, a panel removal tool (plastic, to avoid scratching), and a multimeter to verify power and ground connections. You may also need a firewall grommet kit if your xB does not have an existing hole for the power cable. Most of these tools cost under $30 total if you do not already own them.

The basic installation order is: disconnect the negative battery terminal, remove the factory stereo using the removal tool, disconnect the factory wiring harness and antenna, run the new power and ground cables through the firewall, connect the wiring harness adapter to the factory harness, connect the new stereo to the harness adapter, test power and ground with a multimeter, find the stereo in the opening, install the dash kit, and reconnect the battery. This process typically takes two to four hours for a first-time installer.

The most common mistakes are running the power cable without a fuse holder near the battery (which creates a fire risk), grounding to painted metal instead of bare metal (which prevents the stereo from powering on), and forgetting to test connections before fully securing the unit in the dashboard. Take time at each step to verify your work before moving forward.

Backup camera setup and parking mode features

The DMX1057XR has a dedicated backup camera input, which means when you shift into reverse, the screen automatically switches to show the camera feed. If your xB came with a factory backup camera, you will need a module to convert the factory signal to the format the Kenwood unit expects. If you are adding a camera from scratch, you can choose any aftermarket camera with a standard RCA video output.

The stereo does not have a built-in parking mode or dashcam recording feature. It will display a backup camera feed while in reverse, but it does not record video or monitor the vehicle when parked. If you want those features, you will need a separate dashcam or parking mode camera system installed alongside the stereo.

Camera installation involves running the camera cable from the rear bumper or license plate area through the interior to the back of the head unit. This is the most time-consuming part of a backup camera setup, often taking an hour or more depending on how much interior trim you need to remove to route the cable cleanly.

Sound quality and amplifier considerations

The DMX1057XR includes a built-in amplifier rated at 50 watts per channel, which is sufficient to power the xB's factory speakers at normal listening levels. You do not need an external amplifier to use this stereo, though adding one will increase volume ceiling and bass depth if you listen to music at high levels or want to upgrade your speakers later.

The unit has a subwoofer output, which means you can connect a powered subwoofer (a self-contained unit with its own amplifier) if you want deeper bass. This requires running an additional RCA cable from the stereo to the subwoofer, but no additional amplifier is needed. A powered subwoofer typically costs $150 to $400 and can be placed under a seat or in the cargo area.

The factory xB speakers are adequate but not high-quality. If you are replacing the stereo, many people also upgrade the front door speakers and tweeters at the same time, since the factory units are small and tinny. This is optional and can be done when ready or later, but the DMX1057XR will work fine with the factory speakers if you choose to keep them.

Frequently Asked Questions

Will the DMX1057XR work with my xB if I have a 2003 or older model?

No. The xB was first sold in 2004, so there are no 2003 models. The DMX1057XR fits 2004–2015 xB models. If you have a 2016 or newer xB, you will need to confirm compatibility with Kenwood or your installer, as the dashboard design changed.

Can I use this stereo without running a power cable to the battery?

No. The factory wiring harness does not supply enough power for the DMX1057XR to operate reliably. You must run a dedicated 4-gauge power cable from the battery through the firewall to the stereo. This is not optional and is a safety requirement.

What happens if I connect the steering wheel control module incorrectly?

If the module is wired backward or to the wrong connectors, the steering wheel buttons will not respond, or the stereo may not power on. The module has polarity markings; follow them carefully. If something goes wrong, disconnect the battery, check the connections, and try again.

Do I need professional installation, or can I do this myself?

Most people with basic mechanical skills can install this stereo in a few hours. The most important steps are running the power and ground cables correctly and verifying connections with a multimeter before powering on. If you are uncomfortable working with electrical systems, professional installation costs $100 to $200 and removes the risk of mistakes.

Will Apple CarPlay work wirelessly with this stereo?

No. The DMX1057XR supports Apple CarPlay and Android Auto, but only over a wired USB connection. Wireless CarPlay requires a separate adapter module that costs $50 to $100 and adds complexity to the installation. If wireless CarPlay is important to you, consider a higher-end Kenwood model that includes it built-in.