What happens when you plug into city water at an RV park or campground

When you connect your RV to a city water hookup, you are running pressurized water directly from the municipal supply into your RV's fresh water tank or plumbing system. The connection uses a standard RV water inlet — a threaded port on the exterior of your RV — and a potable water hose that screws onto it. Water flows by pressure alone; you do not need a pump running. This is different from boondocking, where you carry water in your tank and manage it manually.

City water connections are found at most established RV parks, many state and national forest campgrounds, and some day-use areas. The water quality is treated and safe to drink, though mineral content and chlorine levels vary by location. Once connected, you can run your shower, toilet, and kitchen sink as if you were in a house — with one important difference: you need to manage pressure and prevent backflow into the municipal system.

Key Takeaways

  • RV water inlets are threaded ports on your RV's exterior that accept a standard potable water hose, and you should know where yours is located before arriving at a hookup site.
  • You need a dedicated potable water hose rated for drinking water, not a garden hose, because garden hoses can leach chemicals into your water supply.
  • Most city water connections deliver 40 to 60 pounds per square inch of pressure, which can damage your RV's plumbing if you do not use a pressure regulator.
  • Connecting to city water bypasses your fresh water tank, so you can run indefinitely without refilling, but you should still know how to switch back to tank water if the connection fails.

Finding and identifying the water inlet on your RV

Your RV's water inlet is a small threaded port, usually located on the exterior wall near the front or side of the unit. On travel trailers, it is often on the roadside (left side when towing). On motorhomes, check the driver's side or near the main entry door. The inlet is typically labeled with a blue cap or a small blue plastic cover to protect it from dirt and debris.

If you cannot find it, check your RV's manual or walk around the exterior looking for a port about the size of a quarter with a threaded opening. Some older RVs have the inlet on the tongue or frame. Once you locate it, remove the cap and inspect the threads for damage or corrosion. If threads are stripped or cracked, you will need a replacement inlet before you can safely connect to city water.

Choosing the right hose and connections

Use only a potable water hose rated for drinking water — never a standard garden hose. Garden hoses are treated with chemicals that leach into water over time, and they are not designed to carry drinking water. Potable water hoses are labeled clearly and are usually white or translucent. They cost between $15 and $40 for a 25-foot hose, depending on quality and brand.

The hose connects to your RV inlet with a threaded fitting. Most RVs use a standard 5/8-inch or 3/4-inch connection. Check your manual or measure the inlet opening to confirm which size you need. At the other end, the hose connects to the campground's water spigot, which typically has a standard threaded faucet connection. Some campgrounds provide hoses, but bringing your own ensures you know the hose is clean and in good condition.

Installing a pressure regulator to protect your plumbing

City water pressure ranges from 40 to 80 pounds per square inch, depending on the location and time of day. Your RV's plumbing — tanks, valves, and fixtures — is designed for much lower pressure, typically 20 to 40 PSI. Without a pressure regulator, high-pressure water can crack seals, burst hoses, and damage your water heater. A pressure regulator is not optional; it is essential.

A basic pressure regulator costs $15 to $30 and screws onto the campground spigot before you attach your hose. It reduces incoming pressure to a safe level automatically. Some regulators include a filter that removes sediment and chlorine taste. If you use city water regularly, a regulator with a filter is worth the extra $10 to $20. Screw the regulator onto the spigot first, then attach your potable water hose to the regulator's outlet.

Connecting and disconnecting step by step

Before you connect, locate the campground's water spigot — usually a faucet on a post or wall near your site. Turn the spigot handle to confirm it is off, then screw your pressure regulator onto the spigot's threaded outlet. Hand-tighten only; do not use a wrench, which can crack the fitting.

Attach your potable water hose to the regulator's outlet and hand-tighten that connection as well. Walk to your RV and screw the other end of the hose onto your water inlet, again hand-tightening only. Once connected, turn on the campground spigot slowly. Water will flow into your RV's plumbing system. If you have a fresh water tank, you can leave the connection on indefinitely and the tank will stay full. If you want to fill only the tank and then disconnect, turn off the spigot and monitor the tank gauge.

To disconnect, turn off the campground spigot first. Wait a few seconds for pressure to drop, then unscrew the hose from your RV inlet. Water may drip from the connection; have a towel ready. Unscrew the hose from the regulator, then unscrew the regulator from the spigot. Drain any water from the hose by holding it vertically and letting gravity empty it, or coil it loosely and let it dry before storing. Cap your RV's water inlet to keep dirt out.

Switching between city water and tank water

Most RVs have a valve that lets you choose between city water and your fresh water tank. This valve is usually located near your water heater or in a cabinet under the sink. When city water is connected and the valve is set to "city," water bypasses your tank entirely. When you disconnect or want to use stored water, switch the valve to "tank" mode.

If you are unsure where your valve is, check your manual or ask the campground host. Some RVs do not have a manual valve and instead use a one-way check valve that automatically prevents backflow. In those systems, city water pressure forces water into your plumbing, and when you disconnect, the check valve closes and your tank takes over. Either way, you should know how your system works before you need it.

Common problems and how to avoid them

The most frequent issue is forgetting to use a pressure regulator, which leads to burst hoses or damaged fixtures. Always use one, even if the campground says pressure is low. The second common problem is using a garden hose instead of a potable water hose, which contaminates your water. Buy a dedicated potable hose and label it clearly so it does not get mixed up with other hoses.

Frozen hoses are a problem in cold weather. If temperatures drop below freezing, disconnect the hose at night and drain it completely. Some RVers wrap hoses with heat tape or insulation, but disconnecting is simpler and safer. If your hose freezes while connected, do not force it; let it thaw naturally or pour warm (not boiling) water over the frozen section.

Leaks at the connection points are usually caused by cross-threading or over-tightening. Hand-tighten only, and if water drips from a connection, turn off the spigot, unscrew the hose, and reconnect it carefully. If the leak persists, the threads may be damaged and you may need a new hose or inlet.

Frequently Asked Questions

Can I leave my RV connected to city water overnight?

Yes. City water connections are designed for continuous use. Your fresh water tank will stay full, and you can use water normally. The only reason to disconnect is if you are leaving the site for an extended period or if temperatures will drop below freezing.

What if the campground water pressure is very high?

Use your pressure regulator — that is exactly what it is for. If pressure is still causing problems (very slow flow or very fast flow), the regulator may be faulty or set incorrectly. Some regulators have an adjustment screw; check the instructions. If adjusting does not help, try a different regulator.

Do I need to winterize my RV if I use city water?

If you stay connected to city water through winter, you do not need to winterize the plumbing because water is constantly flowing and fresh. However, if you disconnect and temperatures drop below freezing, you should winterize by blowing out the lines or adding RV antifreeze to prevent ice damage in the tanks and pipes.

What happens if I connect without a pressure regulator?

High pressure can crack seals in your water heater, burst hoses, and damage valves and fixtures. Repairs often cost $200 to $500 or more. A $20 pressure regulator prevents all of this damage, so it is always worth using one.

Can I use city water and my tank at the same time?

No. Your RV's valve system switches between one or the other. When city water is connected and the valve is set to city, your tank is isolated. When you switch to tank mode, city water is cut off. You cannot run both simultaneously.