RV awning fabric wears out and needs replacing, usually every 5 to 15 years depending on sun exposure and weather
Your RV awning fabric degrades from ultraviolet light, rain, mildew, and wind stress. When the fabric tears, fades badly, or no longer retracts smoothly, replacement is the practical fix. You can buy fabric alone and install it yourself if you have basic tools and patience, or you can pay an RV shop to do the work. The fabric itself costs between $300 and $800 depending on awning size; labor adds $200 to $600 more if you hire someone.
The job involves removing the old fabric from the roller tube, sliding new fabric onto that tube, and reattaching the arms and hardware. It is not complicated, but it requires you to work at height and handle a heavy roller. Most owners either do it themselves or take the RV to a service center during off-season when shops have availability.
Key Takeaways
- Awning fabric typically lasts 5 to 15 years and fails from sun damage, tears, or mildew rather than mechanical breakdown of the frame.
- Replacement fabric costs $300 to $800 depending on awning width; you can buy it online or from RV suppliers and install it yourself with basic hand tools.
- The replacement process involves removing the old fabric from the roller tube, sliding the new fabric on, and reattaching the support arms — a job that takes 2 to 4 hours for most owners.
- Professional installation at an RV service center adds $200 to $600 in labor but eliminates the risk of damaging the roller tube or misaligning the fabric.
How to measure your awning for replacement fabric
Measure the width of your awning from the outer edge of one arm to the outer edge of the other arm when fully extended. This is the fabric width you need to order. Write down the exact measurement in inches. Most RV awnings come in standard widths: 12, 14, 16, 18, or 20 feet, but some are custom sizes.
Next, measure the length of the roller tube itself — the metal cylinder that the fabric wraps around. This is usually 10 to 14 inches long. Measure from the inside edge of one end cap to the inside edge of the other. The fabric length you order should match this measurement exactly, because the fabric is sewn to fit that specific tube.
Take a photo of your awning model number if it is visible on the arm or frame. Many RV awning manufacturers print this on a sticker. Having the model number lets you order fabric cut to the exact original dimensions, which saves you from measuring twice.
Choosing between DIY replacement and professional installation
A DIY replacement makes sense if you are comfortable working at height, have a helper to hold the roller tube steady, and own basic hand tools: a socket set, screwdrivers, and a drill. The main risk is dropping the roller tube or misaligning the fabric as you slide it on, which can bend the tube or tear the new fabric before you even finish. If either happens, you have wasted the fabric and may need to buy a new roller tube.
Professional installation is worth the cost if you lack tools, do not have a safe way to work at height, or want a may provide that the fabric is aligned correctly and the hardware is torqued to spec. RV service centers have lifts, experience with different awning brands, and can spot problems like a bent tube or worn roller bearings while they work. They also handle disposal of the old fabric.
If you choose DIY, buy the fabric from an RV supplier like Camping World, Etrailer, or a regional RV parts shop. These suppliers often sell fabric pre-cut to standard awning sizes and sometimes include installation instructions specific to your awning model. Fabric from a generic online retailer may not be cut to the right length or may not have the correct hem and attachment points.
Step-by-step DIY replacement process
Start by retracting the awning fully and disconnecting the power if it is motorized. Remove the two support arms by unbolting them from the RV wall and the roller tube. You will need a helper to support the roller tube weight as you remove the second arm — the tube is heavy and will drop if both arms come free at once.
Lay the roller tube on a flat work surface. Remove the end caps (the round covers on each end of the tube) by unbolting or unscrewing them. Slide the old fabric off the tube. If the fabric is glued or riveted to the tube, you will need to cut it away carefully with a utility knife or grind off the rivets with a rotary tool. Work slowly to avoid gouging the tube itself.
Clean the roller tube with a dry cloth to remove any old fabric scraps, adhesive, or debris. Inspect the tube for dents or bends. A bent tube will cause the new fabric to bind or wrinkle, so if you find damage, consider having a shop straighten it or replace it.
Slide the new fabric onto the tube, aligning the attachment points (usually grommets or sewn loops) with the holes or slots on the tube. Some fabrics are glued on; others are bolted or riveted. Follow the instructions that came with your fabric. If you are gluing, use the adhesive recommended by the fabric supplier — not all contact cements work on awning materials. Reinstall the end caps, then bolt the arms back to the tube and the RV wall.
Common problems during replacement and how to avoid them
The most frequent mistake is ordering fabric that is too long or too short for the roller tube. This happens when you measure the awning width instead of the roller tube length, or when you order from a supplier who does not cut to your exact size. Always confirm the tube length before ordering, and ask the supplier to cut the fabric to that measurement.
Misalignment during installation causes wrinkles or binding when you retract the awning. To prevent this, mark the center of the roller tube and the center of the fabric with tape before you slide it on. Align those marks as you work, and check alignment every few inches as you slide the fabric along the tube.
Damaging the roller tube while removing the old fabric is avoidable if you use a utility knife instead of a grinder, and if you cut slowly and at a shallow angle. The tube is aluminum and dents easily. If you do dent it, a small dent will not affect function, but a large one or a bend will cause the fabric to bind.
Forgetting to clean the tube before installing new fabric traps old adhesive or debris under the new fabric, which can cause it to slip or wrinkle. Spend 10 minutes wiping the tube down with a dry cloth and inspecting it for damage before you start the installation.
Fabric types and durability differences
Most RV awning fabric is acrylic or vinyl-coated polyester. Acrylic is lighter, breathes better, and resists mildew, but it fades faster in strong sun and costs less — typically $300 to $500 for a standard awning. Vinyl-coated polyester is heavier, blocks more light, and lasts longer in harsh climates, but it costs more ($500 to $800) and can trap moisture underneath if ventilation is poor.
Some suppliers offer solution-dyed acrylic, which means the color is built into the fiber rather than applied to the surface. This type resists fading better than standard acrylic and often comes with a 5-year fade warranty. If you live in a high-sun area like Arizona or Florida, solution-dyed acrylic or vinyl is worth the extra cost because it will last longer before fading badly.
Check whether the fabric you are considering has UV protection built in. Many modern awning fabrics include UV inhibitors that slow fading and degradation. This is especially important if your RV sits in the sun for weeks at a time during storage.
When to replace the roller tube instead of just the fabric
The roller tube itself rarely fails, but it can bend, crack, or develop seized bearings. If you notice the awning retracts unevenly, makes grinding noises, or the fabric binds on one side, the tube may be damaged. Before you buy new fabric, have a shop inspect the tube under load.
A bent tube will cause any new fabric you install to wrinkle or bind, so replacing just the fabric will not fix the problem. If the tube is bent, you can have it straightened by a machine shop or replaced by an RV service center. Tube replacement costs $400 to $800 in labor and parts, so it is more expensive than fabric alone, but necessary if the tube is the root cause.
Seized bearings at the ends of the tube make the awning hard to retract manually or cause the motor to strain. This usually means the end caps need replacement, not the whole tube. End caps cost $50 to $150 each and are easier to replace than the tube itself.
Frequently Asked Questions
Can I patch a torn awning instead of replacing the whole fabric?
Small tears (under 2 inches) can be patched with a vinyl repair kit from an RV supplier, but patches are temporary and visible. Large tears or multiple tears across the fabric mean the material is degrading overall, so replacement is more cost-effective than patching. A patch also creates a weak point that may tear again under wind stress.
How long does it take to replace awning fabric yourself?
Most DIY replacements take 2 to 4 hours, depending on how stuck the old fabric is and whether you have a helper. If the old fabric is glued on and difficult to remove, add another hour. Professional shops usually complete the job in 1 to 2 hours because they have specialized tools and experience.
What should I do if the new fabric does not align properly after installation?
Stop and do not retract the awning fully until you fix the alignment. Retracting misaligned fabric can damage it or jam the roller. Remove the end caps, slide the fabric slightly to correct the alignment, and reinstall the caps. If the fabric is glued, you may need to remove it and start over.
Is there a way to extend the life of my current awning fabric?
Keep the awning retracted when the RV is not in use, especially in high-sun areas. Clean mildew with a soft brush and mild soap as soon as you see it. explore a UV protectant spray designed for awning fabric once or twice a year. These steps slow fading and mildew growth but do not prevent eventual replacement.
Can I use fabric from a different brand than my original awning?
Yes, as long as the fabric is cut to match your roller tube length and width. Universal awning fabric from suppliers like Etrailer or Camping World works on most standard RV awnings. Confirm the tube dimensions with the supplier before ordering to avoid sizing problems.