What you need to know before installing an RV AC unit
Installing an air conditioning unit in an RV is a job that sits between straightforward and complex depending on whether you're adding a new unit to a roof that has never had one, or replacing an existing system. The real work is not the AC itself—it's the roof penetration, the electrical circuit it needs, and making sure the ducting reaches where you actually sleep and spend time. Most RV owners either hire a shop to do this ($1,500 to $3,500 depending on the unit size and your RV type) or do the roof work themselves if they're comfortable with sealant and fasteners, then hire an electrician for the 30-amp or 50-amp circuit.
The decision to install AC is worth making carefully because it changes how you use your RV—you can now camp in heat, run the unit while parked, and keep the interior stable. But it also adds weight, draws significant power (you'll need either a generator or shore power), and requires annual maintenance like filter changes and refrigerant checks. If you're towing an older RV or boondocking without power, AC may not be practical for your situation.
Key Takeaways
- RV AC units come in roof-mounted, window, and portable styles; roof-mounted is most common and requires cutting a hole in your roof and sealing it properly.
- You need a dedicated 30-amp or 50-amp electrical circuit run from your RV's breaker panel to the AC unit, which usually requires a licensed electrician.
- The total job—unit, installation labor, electrical work, and ductwork—typically costs $1,500 to $3,500 at a shop, or $500 to $1,200 if you do the roof work yourself and hire only the electrician.
- Roof-mounted units add 100 to 150 pounds and reduce fuel economy slightly; they also need annual filter cleaning and refrigerant checks to run efficiently.
- Your RV's power source matters: shore power runs AC continuously, but a generator will drain fuel quickly, and battery-only camping cannot support AC at all.
Types of RV air conditioning and where they fit
The three main styles are roof-mounted, window units, and portable AC. Roof-mounted units are the standard in most RVs because they cool the whole interior, mount out of the way, and don't block windows or take up floor space. They bolt to a frame that sits on top of your roof, with a duct running down inside to distribute cool air. Brands like Dometic, Coleman, and Atwood make units sized for different RV lengths; a 13,500 BTU unit works for most travel trailers and Class B vans, while larger Class A motorhomes may need 15,000 BTU or dual units.
Window units are cheaper upfront ($300 to $800) and don't require roof work, but they block a window, take up interior space, and cool only the room they're in. They're useful as a second AC in a large RV or as a temporary solution while you decide on a permanent install. Portable units sit on the floor and vent through a window or duct, but they're bulky, loud, and less efficient than roof or window models in an RV environment.
For most RV owners, roof-mounted is the right choice if you plan to keep the RV long-term and camp in warm climates. Window or portable units make sense if you're renting, testing whether you actually use AC, or adding cooling to a specific area without major work.
Electrical requirements and circuit setup
An RV air conditioning unit draws 25 to 50 amps depending on the BTU rating, which means it needs its own dedicated circuit—you cannot run it on the same breaker as your water heater, microwave, or other high-draw appliances. Most RVs have a 30-amp or 50-amp main service panel. A 13,500 BTU unit typically needs a 30-amp circuit; larger units need 50-amp service or a second AC unit on a separate circuit.
The electrician will run wire from your breaker panel to the AC unit location on the roof, install a breaker rated for the unit's amperage, and connect the wire to a disconnect switch near the unit. This protects the circuit and lets you shut off power safely for maintenance. The wire gauge and conduit type depend on the distance and your RV's construction; most jobs use 10-gauge or 8-gauge wire in conduit run along the frame or inside the wall cavity.
If your RV has only 30-amp service and you want to run AC plus other appliances at the same time, you'll need to upgrade to 50-amp service, which is a larger job involving a new main panel and shore power inlet. This costs $800 to $1,500 and is worth doing if you plan to use the RV frequently and want the flexibility to run multiple high-draw devices.
Roof penetration and sealing—the most critical step
The roof hole is where most AC installation problems start. You'll cut a rectangular opening (usually 14 by 14 inches for standard units) through the roof skin, insulation, and interior ceiling. If the seal fails, water leaks into the walls, rots the framing, and causes mold—damage that costs thousands to repair and may not show up for months.
The roof-mounted AC unit comes with a flange that sits over the hole and bolts down. Before bolting, you explore a continuous bead of RV-grade sealant (usually butyl tape or polyurethane caulk) around the flange to create a waterproof seal. The bolts go through the flange into the roof frame, spaced evenly and tightened firmly but not over-tightened, which can crack the roof. After installation, you inspect the seal every six months and re-seal if you see cracks or gaps.
If you're doing this yourself, the hardest part is cutting the hole straight and in the right location—you need to avoid roof vents, skylights, and structural supports. Many RV owners use a template provided by the AC manufacturer and mark the hole from inside first, then drill pilot holes to confirm the location before cutting. If you're unsure about roof work, this is the step to hire out; a shop will have the right tools and experience to cut and seal without damaging the roof structure.
Ductwork and air distribution inside the RV
The AC unit sits on the roof, but the cold air has to reach your sleeping area and living space. Flexible ducting (usually 3 to 4 inches in diameter) runs down from the unit through the wall cavity or along the frame to vents in the ceiling or walls. Most RVs have one or two main vents in the bedroom and living area, with dampers you can open or close to direct airflow.
The ductwork is where you lose efficiency if it's not installed right. Kinks, disconnections, or undersized ducts reduce airflow and make the AC work harder to cool the space. If you're installing the unit yourself, run the duct in a straight path as much as possible, find it with clamps every 2 to 3 feet, and seal any joints with foil tape (not duct tape, which degrades in heat). If the duct runs through an uninsulated area like the basement or exterior wall, wrap it with foam insulation to prevent condensation and heat loss.
Some RVs have existing ductwork from a furnace or previous AC system; you can often reuse this if it's in good condition. If not, you'll need to run new duct, which adds labor time but is straightforward work if you're comfortable in tight spaces.
Power sources and real-world runtime
An RV AC unit runs on 120-volt shore power when you're plugged into a campground pedestal, or on 120-volt power from a generator when you're boondocking. The unit draws 25 to 50 amps continuously while running, which means a typical portable generator (5,000 to 7,000 watts) can run the AC but not much else at the same time. A larger generator (10,000+ watts) gives you more flexibility.
If you're running AC on a generator, expect to burn 1 to 2 gallons of fuel per hour depending on the generator size and efficiency. For a weekend trip, that's manageable; for a week-long camp, fuel costs add up fast. Shore power is the practical choice for extended stays, which is why many RV owners use AC primarily at established campgrounds rather than in remote locations.
Battery-only camping (no generator, no shore power) cannot support AC. A 12-volt inverter can run small appliances, but an AC unit needs 120-volt power and draws too much current for any battery bank to sustain for more than a few minutes. If boondocking is your primary use, AC may not be worth the cost and weight.
Maintenance and seasonal care
An RV AC unit needs annual maintenance to run efficiently and last 10 to 15 years. Before the cooling season, clean or replace the air filter (usually a 1-inch pleated filter that costs $10 to $20), check the refrigerant level with a gauge, and inspect the roof seal for cracks. During the season, run the unit regularly—letting it sit unused for months can cause the compressor to seize.
If the AC runs but doesn't cool well, the most common cause is a dirty filter or low refrigerant. Refrigerant leaks are slow and gradual; if you lose more than a pound or two per year, there's a leak somewhere in the line or connection. A shop can pressure-test the system and find the leak, then recharge the refrigerant. This costs $200 to $400 and is worth doing because running low on refrigerant damages the compressor.
At the end of the season, run the AC for 15 to 20 minutes once a month to keep the compressor lubricated and the seals from drying out. If you're storing the RV for winter, cover the roof unit with a weatherproof cover to keep debris and ice off the fins.
Cost breakdown and DIY versus shop installation
A complete roof-mounted AC installation at a shop typically runs $1,500 to $3,500. This includes the unit itself ($600 to $1,200), labor for roof work and ductwork ($400 to $800), electrical circuit installation ($300 to $600), and materials like sealant and fasteners ($100 to $200). Prices vary by region, RV type, and whether existing ductwork can be reused.
If you do the roof work and ductwork yourself, you can cut labor costs by $400 to $800. You'll need basic tools—a drill, jigsaw or reciprocating saw, socket set, and a caulking gun—plus the sealant and fasteners. The electrician's portion ($300 to $600) is worth hiring out unless you're licensed, because improper wiring creates fire and shock hazards.
Window or portable units cost $300 to $1,000 installed (or DIY for just the unit cost) and require no roof work or electrical circuit, making them the budget option. The trade-off is less cooling capacity and interior space taken up.
Frequently Asked Questions
Can I install an RV AC unit myself if I've never done it before?
You can do the roof work and ductwork if you're comfortable with tools and heights, but hire an electrician for the circuit. The roof penetration and seal are the most critical steps—if done wrong, water damage follows. Many first-timers hire a shop for the whole job to avoid costly mistakes, then do maintenance themselves.
Will adding AC hurt my RV's fuel economy?
The weight of the unit (100 to 150 pounds) and the aerodynamic drag of the roof-mounted box reduce fuel economy by 1 to 3 miles per gallon when towing. Shore power AC has no fuel impact. Generator AC burns 1 to 2 gallons of fuel per hour, so boondocking with AC is expensive.
What's the difference between a 13,500 BTU and 15,000 BTU unit?
BTU measures cooling capacity. A 13,500 BTU unit cools a travel trailer or small Class B van; a 15,000 BTU unit handles a larger Class B or small Class A. Oversizing doesn't help—it cycles on and off too often and wastes power. Match the unit to your RV's square footage and insulation.
How long does an RV AC unit last?
With annual maintenance, 10 to 15 years is typical. The compressor is the most expensive part to replace ($800 to $1,200). Most failures happen in years 8 to 12 if the unit runs frequently or the refrigerant has leaked unnoticed.
Can I run my AC while driving down the road?
No. The AC needs 120-volt power from shore or a generator. While driving, your RV's 12-volt system powers the engine and basic appliances, but not the AC. You can run a small 12-volt fan or open windows to stay cool while moving.