What the Motion Pro Cable Luber does
The Motion Pro Cable Luber is a hand-operated tool that forces lubricant into the inner cable of motorcycle and ATV throttle, clutch, and brake cables without removing them from the bike. It works by creating a seal around the cable housing, then using a plunger to push oil down the length of the cable under pressure. The tool costs between $25 and $40 and is designed to extend cable life by reducing friction and corrosion inside the housing.
Most riders use it when a cable starts feeling stiff or sticky — the kind of problem that shows up as sluggish throttle response or a clutch that doesn't fully disengage. The alternative is replacing the cable entirely, which costs more in parts and labor. The luber lets you refresh an existing cable in about five minutes without disconnecting anything.
Key Takeaways
- The Motion Pro Cable Luber pumps oil into sealed cable housings to restore smooth operation without cable removal.
- You use it when a cable feels stiff or sticky, which usually happens after 1,000 to 3,000 miles of riding or after exposure to salt and moisture.
- The tool works on any motorcycle or ATV cable with a sealed housing, but not on older open-style cables or sealed cables that have no access point.
- A single lubrication session takes about five minutes and costs less than $5 in oil, compared to $30 to $80 for a new cable plus installation time.
How to use the Motion Pro Cable Luber
Start by locating the cable housing access point — usually a small opening at the top or bottom of the cable run. Wipe away any dirt or debris around that opening. Unscrew the luber's cap and fill the reservoir with light machine oil or the cable lube Motion Pro sells separately; don't use heavy gear oil or grease, which will clog the cable.
Slide the luber's nozzle over the cable housing opening and push down firmly until you feel it seal. Pump the plunger handle 10 to 15 times in steady strokes. You should feel resistance as the oil is forced down the cable. Stop when oil begins to drip out the other end of the housing, or when the plunger becomes very hard to push — either sign means the cable is saturated. Wipe away any excess oil with a rag and test the cable's movement by working the lever or throttle by hand.
If the cable still feels stiff after lubrication, the housing may be kinked, the cable may be frayed inside, or the problem may be at the lever itself rather than the cable. In those cases, replacement is the next step.
When lubrication actually helps versus when it doesn't
Lubrication works best on cables that have become stiff due to dried-out lube or light surface corrosion — the kind of problem that develops gradually over a season or two. If you ride in salt spray, rain, or dusty conditions, your cables will dry out faster, and regular lubrication can add months or years to their life.
Lubrication does not fix a cable that is already kinked, frayed, or broken inside the housing. It also won't help if the problem is at the lever end — a bent lever, a stuck pivot, or a worn cable anchor. Before you lubricate, work the lever or throttle by hand to feel where the resistance is. If it's smooth at the lever but stiff in the middle of the cable run, lubrication will likely help. If the stiffness is at the lever itself, you're looking at a different repair.
On older bikes with open-style cables (no housing), the luber won't work at all — those cables need to be removed and hand-lubricated or replaced. Check your cable before buying the tool; if there's no sealed housing, you'll need a different approach.
Comparing the Motion Pro Cable Luber to other options
| Method | Cost | Time | Best for |
|---|---|---|---|
| Motion Pro Cable Luber | $25–$40 tool + $3–$5 per use | 5 minutes | Stiff cables on sealed housings; repeated maintenance |
| Spray cable lube (WD-40, Tri-Flow) | $5–$8 per can | 2 minutes | Quick temporary relief; open-style cables |
| Cable replacement | $30–$80 parts + labor | 30 minutes to 1 hour | Kinked, frayed, or broken cables |
| Remove and hand-lubricate | $3–$5 oil | 45 minutes to 1 hour | Thorough cleaning; older bikes with open cables |
Spray lubes like WD-40 or Tri-Flow are cheaper and faster but don't penetrate sealed housings as effectively — the oil sits on the outside and runs off. They work better on open cables or as a temporary fix between deeper lubrications. If you ride regularly and want to keep cables in good shape, the Motion Pro tool pays for itself after three or four uses.
Hand-lubrication (removing the cable and oiling it by hand) is the most thorough method but requires disconnecting the cable, which takes time and carries the risk of losing adjustment. Most riders reserve this for off-season maintenance or when a cable is already damaged.
Who should own a Motion Pro Cable Luber
Buy one if you ride a motorcycle or ATV regularly and want to extend cable life without replacing them often. It's especially useful if you ride in wet, salty, or dusty conditions, or if you keep your bike for several years. Casual riders who put on a few hundred miles a year may not need it — their cables won't dry out as fast.
If you own multiple bikes or work on bikes for others, the tool is a worthwhile investment. It's small, stores easily, and works on any sealed cable. If you only own one bike and rarely ride it, a can of spray lube and a replacement cable on hand will probably serve you better.
Maintenance and storage
After each use, wipe the nozzle clean with a rag to prevent oil buildup. Store the luber with the cap on and the reservoir either empty or filled — an empty reservoir is safer if you're storing it for months. The tool itself has no moving parts that wear out, so it should last indefinitely if you don't drop it or crack the plastic reservoir.
Keep your oil separate from the tool. Light machine oil, 3-in-1 oil, or Motion Pro's branded cable lube all work; don't mix types or store oil in the reservoir for more than a few months, as it can thicken or separate. If you're storing the tool for winter, empty the reservoir completely to avoid spills.
Frequently Asked Questions
Can I use the Motion Pro Cable Luber on car door locks or other cables?
The tool is designed for motorcycle and ATV throttle, clutch, and brake cables, which have a specific housing diameter. Car door lock cables and other automotive cables may have different dimensions and may not seal properly with the luber's nozzle. Check the diameter of your cable housing against the luber's specifications before trying it on anything other than a motorcycle or ATV.
What happens if I use the wrong type of oil?
Heavy oils like gear oil or grease will clog the cable and make it harder to move, not easier. Stick to light machine oil, 3-in-1 oil, or cable-specific lube. If you accidentally use the wrong oil, you'll need to remove the cable and flush it out by hand or replace it entirely.
How often should I lubricate my cables?
Most riders lubricate cables once or twice a season, or whenever they start to feel stiff. If you ride in wet or salty conditions, you may need to do it more often — every few months. If you ride in dry conditions and store your bike indoors, once a year may be enough.
Will lubrication fix a cable that won't return to idle?
If the throttle cable is sticking and won't snap back, lubrication may help if the problem is friction inside the housing. However, if the cable is kinked, the housing is bent, or the return spring is broken, lubrication won't fix it. Test the cable by hand first — if it moves smoothly at the lever but sticks in the middle, lubrication is worth trying.
Do I need to remove the cable to use the Motion Pro Cable Luber?
No — that's the main advantage of the tool. It works while the cable is installed on the bike. You just need access to the cable housing opening, which is usually at the top or bottom of the cable run.