What a Lippert leveling system reset does and when you need one

A Lippert leveling system is the hydraulic mechanism that raises and lowers your RV's jacks to level the vehicle when parked. A reset clears error codes from the system's control panel and recalibrates the sensors so the jacks can operate normally again. You need a reset when the panel displays an error code, the jacks won't respond to button commands, or the system thinks your RV is level when it clearly isn't.

The reset process differs slightly depending on which Lippert control panel you have — the most common are the Leveling Cohn and the Lippert StableLoad systems — but the basic steps are similar across models. A reset does not fix mechanical damage to the jacks themselves, broken hydraulic lines, or a dead battery; it only tells the electronics to start fresh and recalibrate.

Key Takeaways

  • A Lippert leveling system reset clears error codes and recalibrates sensors, but does not repair physical damage to jacks or hydraulic components.
  • The reset process usually involves locating the control panel (often under the kitchen sink or in a cabinet), holding a reset button for several seconds, and waiting for the system to recalibrate.
  • Your RV must be parked on level ground and the battery must be fully charged before you attempt a reset.
  • If the system still shows an error code after a reset, the problem is likely mechanical or electrical and requires a technician to diagnose.

Prepare your RV before attempting a reset

Before you touch the control panel, make sure your RV is parked on level ground — not slightly tilted or on a slope. The leveling system uses sensors to detect what "level" means, and if the RV is already tilted, the recalibration will lock in that tilt as the new baseline. Use a bubble level on your kitchen counter or a smartphone level app to verify.

Check that your RV battery is fully charged. A low battery can cause the reset to fail or the system to malfunction during recalibration. If you are plugged into shore power, the battery should charge while you work. If you are boondocking, run the engine or a generator for 30 minutes before starting the reset.

Turn off the leveling system at the control panel and wait 30 seconds. This clears any temporary glitches before you begin the formal reset. Then locate your control panel — it is usually mounted inside a cabinet near the kitchen sink, in a bedroom closet, or under a dinette seat. Check your owner's manual if you cannot find it; the manual will also tell you which model panel you have.

Reset steps for Lippert Leveling Cohn panels

The Leveling Cohn panel has a small reset button, usually recessed so you cannot press it by accident. You may need a pen or a straightened paperclip to reach it. Press and hold the reset button for 5 to 10 seconds until you see the display flash or hear a beep. Release the button and wait for the panel to cycle through its startup sequence — this usually takes 30 to 60 seconds.

Once the panel finishes its startup, it will display the current status of each jack. The system is now recalibrated. Press the "Level" or "Auto" button to run a full leveling cycle. The jacks will extend and retract as the system re-learns the height of each corner. Do not interrupt this cycle — let it run to completion even if it seems to take longer than usual.

After the leveling cycle finishes, check the display. If it shows all jacks at zero or displays a level indicator, the reset worked. If an error code reappears, note the code number and consult your manual or contact Lippert customer support with that code.

Reset steps for Lippert StableLoad and newer systems

Newer Lippert systems, including StableLoad models, often have a touchscreen or button panel instead of a recessed reset button. Look for a "Menu" or "Settings" button on the panel face. Press it to enter the settings menu, then scroll to "System Reset" or "Recalibrate." Select that option and confirm when the panel asks you to verify.

The system will display a countdown or progress bar while it recalibrates. This process can take 2 to 5 minutes. Do not turn off the RV, close the cabinet, or press any other buttons during this time. Once the recalibration is complete, the panel will return to the main screen and display the jack status.

Run a test leveling cycle by pressing the "Level" or "Auto" button. Watch the jacks extend and retract to confirm they are responding to commands. If the system levels the RV smoothly and the error code is gone, the reset was successful.

What to do if the error code returns after a reset

If you complete the reset and the same error code reappears within a few minutes, the problem is not a software glitch — it is a mechanical or electrical fault. Common causes include a broken sensor on one of the jacks, a hydraulic leak, a corroded electrical connector, or a faulty solenoid valve that controls hydraulic pressure.

Write down the exact error code displayed on the panel. Contact Lippert customer support at 1-844-LIPPERT (1-844-547-7738) or visit their website to look up what that code means. You can also consult your RV manufacturer's service department; they often have Lippert technicians on staff or can refer you to a certified dealer.

Do not attempt to operate the jacks repeatedly if an error code persists. Forcing a faulty system to work can damage the hydraulic pump or cause the jacks to lower unexpectedly, which is a safety hazard. Have the system inspected by a technician before using it again.

Common reasons a reset does not solve the problem

A reset clears the control panel's memory but does not fix a broken jack, a cracked hydraulic line, or a dead battery. If your jacks were not responding before the reset, they likely will not respond after it either — the reset just confirmed that the electronics are working and the problem is elsewhere.

Sensor failures are another common reason a reset does not help. Each jack has a height sensor that tells the control panel how far the jack has extended. If a sensor is corroded, loose, or damaged, the panel will not trust its reading and will throw an error code even after a reset. A technician can test each sensor with a multimeter to identify which one is failing.

Battery voltage that is too low can also prevent a successful reset. If your battery is below 12 volts, the control panel may not have enough power to complete the recalibration sequence. Charge the battery fully and try again before assuming the system is broken.

When to call a technician instead of resetting

If your RV is still under warranty, contact your RV dealer before attempting any reset. Some dealers require that you let them diagnose the problem first, and a reset might void your warranty claim if the issue turns out to be a manufacturing defect.

If you hear grinding, squealing, or hissing sounds from the jacks when you press the level button, do not reset the system. These sounds usually mean the hydraulic pump is failing or there is a leak. Resetting will not fix these problems and may make them worse. Have a technician inspect the hydraulic system before you operate the jacks again.

If the jacks lower on their own without you pressing any buttons, or if they lower faster than usual, stop using the system when ready. This is a sign of a hydraulic leak or a faulty solenoid. A reset will not address these safety issues.

Frequently Asked Questions

Will resetting my leveling system erase any other settings in my RV?

No. A Lippert leveling system reset only affects the leveling control panel and jacks. It does not touch your RV's main computer, appliances, or other systems. Your radio presets, thermostat settings, and other configurations will remain unchanged.

How often should I reset my leveling system?

You should only reset the system when an error code appears or the jacks stop responding to commands. Resetting it regularly is not necessary and will not improve performance. Frequent resets may indicate a recurring problem that needs professional diagnosis.

Can I reset the system while my RV is plugged into shore power?

Yes. Shore power charges your battery while you work, which is actually ideal. Make sure the battery itself is in good condition and fully charged before you start. If your battery is old or damaged, shore power alone may not provide enough voltage for a successful reset.

What does it mean if the panel shows different error codes after each reset?

Changing error codes usually mean the control panel is detecting different faults each time it recalibrates. This often points to a loose electrical connection, a corroded sensor, or inconsistent hydraulic pressure. Write down all the codes you see and provide them to a technician, as the pattern can help identify which component is failing.

Is it safe to drive my RV after a reset if the jacks are still extended?

No. Never drive with the jacks extended. Retract all jacks fully before moving the RV, even if you just completed a reset. If the jacks will not retract after a reset, do not drive the RV. Have it towed to a service facility instead.