What a John Deere track loader is and what it does

A John Deere track loader is a compact construction machine with a cab, engine, and hydraulic arms mounted on a steel frame that rides on rubber or steel tracks instead of wheels. The tracks grip soft ground, mud, and snow far better than tyres would, which is why you see them on job sites where the ground is torn up or unstable. The machine lifts and moves material—dirt, gravel, mulch, snow—using a bucket or other attachment on the front arm.

The engine powers a hydraulic system. That system is the real workhorse: it moves the arm up and down, opens and closes the bucket, and turns the tracks left and right. Everything you see the machine do comes from pressurised fluid flowing through hoses and cylinders. When something breaks on a track loader, it is almost always either the engine, the hydraulic system, or the tracks themselves.

John Deere makes several sizes, from the CT332 (compact, about 3 tonnes) to the CT575 (larger, about 5.7 tonnes). The bigger the machine, the more power it has and the more material it can move in a day. Rental yards stock them because they are tough, parts are available, and dealers know how to fix them.

Key Takeaways

  • Track loaders use a hydraulic system to move the bucket and tracks, so hydraulic fluid condition and hose integrity are the first things to check before each use.
  • The tracks themselves wear out and can be adjusted or replaced; loose tracks cause poor steering and damage to the undercarriage.
  • Engine oil, coolant, and fuel filters need regular changes because the machine often works in dusty or muddy conditions that clog filters faster than on a car.
  • Hydraulic fluid heats up during heavy work, so the cooler must stay clean and the fluid level must stay correct or the system will overheat and fail.
  • Most track loader maintenance is visual—checking for leaks, listening for odd noises, and feeling whether the controls respond smoothly—before you rent or buy.

How the hydraulic system works and why it fails

The engine turns a pump that forces hydraulic fluid (usually a mineral oil) into a network of hoses, cylinders, and valves. When you move the joystick, you open a valve that lets pressurised fluid flow into a cylinder. The fluid pushes a piston, the piston moves a rod, and the rod lifts the arm or closes the bucket. When you release the joystick, the valve closes and the fluid stops moving.

Hydraulic fluid degrades over time. Heat, moisture, and dirt all break it down. When fluid breaks down, it becomes thicker, flows slower, and loses its ability to protect metal parts from friction. A machine that works hard in summer or in dusty conditions will degrade its hydraulic fluid faster than one that sits in a climate-controlled shed.

Hoses crack and leak. A small leak drips fluid onto the ground and slowly empties the reservoir. A large leak means the arm drops suddenly or the tracks stop responding. You can spot a leak by looking under the machine after it has been parked for an hour—fluid will pool or drip. Hoses also fail when they are kinked, rubbed against sharp edges, or exposed to extreme heat near the engine.

The hydraulic cooler (a radiator-like device that cools the fluid) gets clogged with dirt and dust. When the cooler is blocked, fluid temperature rises. Hot fluid is thin fluid, and thin fluid leaks more easily and protects less well. A machine that overheats will lose power, move slowly, and eventually shut down as a safety measure.

Track wear, adjustment, and replacement

The tracks are rubber or steel belts that wrap around wheels and idlers (unpowered wheels that support the frame). As the machine moves, the belt flexes and the rubber or steel wears. Wear happens faster on hard ground, on slopes, and when the machine is turned sharply while moving forward.

A loose track causes the machine to pull to one side, makes steering sluggish, and allows the track to slip off the wheels. You can check track tension by pushing on the track midway between the wheels—it should move about 25 to 50 millimetres (1 to 2 inches) up and down. If it moves more than that, it needs tightening. Tightening is done by adjusting bolts on the idler wheel; it is not a job for someone without experience, because over-tightening breaks the idler bearing.

A worn track loses grip and can slip on slopes or soft ground. The rubber or steel becomes thin, and the lugs (the raised bumps that dig into soil) wear smooth. When a track is worn out, it must be replaced. A new track costs between £500 and £1500 depending on the machine size and whether you choose rubber or steel. Replacement takes a few hours and requires a lift or pit to get the machine off the ground.

Engine maintenance and fuel system care

The engine in a track loader is usually a diesel engine—tough, fuel-efficient, and able to run all day. Like any engine, it needs clean oil, clean fuel, and clean air to run well. Dirt in any of those three will clog the engine and cause it to lose power or fail to start.

Oil changes should happen every 250 to 500 hours of use, depending on the model and how dirty the work is. A machine that digs in sandy soil will need oil changes more often than one that moves gravel on a paved lot. The oil filter should be changed at the same time. Skipping oil changes is the fastest way to wear out an engine—metal particles build up in the oil, and they scratch the cylinder walls and bearings.

Fuel filters clog faster on track loaders than on cars because the machines often work in dusty places and fuel tanks can collect sediment. A clogged fuel filter starves the engine of fuel, and the machine will not start or will stall under load. Fuel filters should be inspected every 100 hours and changed every 500 hours or when the machine becomes hard to start.

The air filter protects the engine from dust. In very dusty work, the air filter can clog in a single day. A clogged air filter makes the engine run rich (too much fuel, not enough air), which wastes fuel and creates black smoke. Check the air filter before each day of work if the site is dusty; replace it when you can see dirt caked on the pleats.

Coolant system and temperature management

The engine produces heat, and the coolant system carries that heat away. Coolant flows through passages in the engine block, then through a radiator where air cools it, then back to the engine. If the coolant level drops, the engine overheats. If the radiator is clogged with dirt, the coolant cannot cool properly and the engine overheats.

Check the coolant level when the engine is cold, before you start work. The reservoir has a minimum and maximum line; the level should be between them. If it is low, top it up with the correct coolant type—mixing coolant types can cause corrosion inside the engine. If the level drops repeatedly, there is a leak somewhere: check hoses, the radiator, and the water pump for cracks or loose clamps.

The radiator fins (the thin metal blades that cool the fluid) collect dirt, chaff, and dust. Blow them clean with compressed air or rinse them gently with water from a hose. Never use a pressure washer on the radiator—the force can bend the fins and reduce cooling. A dirty radiator is one of the most common reasons a track loader overheats on a hot day.

Steering, brakes, and control system checks

Track loaders steer by slowing or stopping one track while the other keeps moving. There is no steering wheel—you use a joystick or levers to control each track independently. If one track does not respond, the machine will not turn properly and may pull hard to one side.

Brakes on a track loader are usually wet brakes—brake pads that sit inside the hub of each track wheel and are cooled by hydraulic fluid. Wet brakes are reliable but need the correct fluid level to work. If the hydraulic fluid level is low, braking power drops and the machine will not stop as quickly. This is a safety issue: a machine that cannot stop is dangerous on a slope or near people.

Before you use a track loader, test the controls on flat ground. Move the joystick or levers through their full range and listen for grinding, squealing, or hesitation. The machine should respond smoothly and both tracks should move at the same speed when you move the joystick straight forward. If one track lags or the machine pulls to one side, the steering system or a track needs attention.

Pre-operation inspection and what to look for

Before you rent or buy a track loader, walk around it and look for signs of neglect or damage. Check for hydraulic fluid leaks under the machine and along all hoses. Leaks are dark stains or wet spots on the ground or on the frame. A few drops are normal; a puddle means something is broken.

Look at the tracks. Are they cracked, torn, or missing lugs? Do they sit evenly on the wheels, or is one side higher than the other? Uneven tracks mean the machine has been in an accident or the frame is bent. Spin each track by hand (if the machine is off) and feel for grinding or rough spots—those suggest a bearing is failing.

Check the engine compartment. Is the oil level correct? Is the coolant level correct? Are hoses cracked or leaking? Is the air filter clogged? Start the engine and listen for knocking, grinding, or squealing. Let it idle for a minute and watch the temperature gauge—it should rise slowly and level off, not spike suddenly.

Move the bucket and arm through their full range. They should move smoothly and hold their position when you release the controls. If the arm drifts down slowly, the hydraulic cylinders are leaking internally. If the bucket does not close fully, the hydraulic valve may be stuck or the cylinder may be damaged.

Frequently Asked Questions

How often should I change the hydraulic fluid?

Hydraulic fluid should be changed every 1000 to 2000 hours of use, depending on how hard the machine works and how dirty the environment is. If the machine works in dusty or wet conditions, change it more often. You can also have the fluid tested—a lab can tell you whether it is still good or has degraded too much to use.

What does it mean if the track loader pulls to one side?

Pulling usually means one track is loose, one track is worn more than the other, or the steering system is not balanced. Check track tension first—a loose track is the most common cause. If both tracks are tight and wear looks even, the steering valve may need adjustment or the hydraulic pressure to one track may be low.

Can I use a track loader in winter?

Yes, but you need to prepare it. Use winter-grade hydraulic fluid and engine oil rated for cold temperatures. Keep the coolant topped up with the correct antifreeze. Check the battery—cold reduces battery power, and a weak battery will not turn over a diesel engine. Clear snow and ice from the radiator and cooler so they can cool properly.

What is the difference between rubber and steel tracks?

Rubber tracks grip soft ground better and are quieter on pavement. Steel tracks last longer on rough ground and sharp rocks, but they are noisier and can damage asphalt. Rubber tracks cost less to replace but wear faster. Steel tracks cost more but last two to three times as long. Choose based on where the machine will work most.

How much does it cost to replace a track loader engine?

A used engine costs £2000 to £5000 depending on hours and condition. A new engine costs £8000 to £15000. Labour to remove and install an engine takes 20 to 40 hours. Most owners choose to rebuild the engine instead—a rebuild costs £3000 to £7000 and takes 40 to 60 hours. For a rental machine, engine replacement usually means the machine is retired.