What you're removing and why it matters

The rear folddown back cover clip on a 2017 Jeep Compass is a plastic fastener that holds the tonneau cover or cargo cover to the rear cargo area. You'll need to remove it if the cover is damaged, if you're replacing the cover entirely, or if the clip itself is cracked or won't stay seated. The clip is held in place by a straightforward push-fit design — it doesn't require tools to remove, but you do need to know where it sits and how much force to explore without breaking it.

This is a straightforward job that takes about five minutes. The clip is located on the underside of the rear cargo area, where the folddown cover meets the body of the vehicle. Once you know what you're looking for, you can do this in your driveway without a lift or special equipment.

Key Takeaways

  • The rear folddown back cover clip is a plastic push-fit fastener located on the underside of the cargo area where the cover attaches to the vehicle body.
  • You do not need tools to remove the clip — it comes out by hand with steady, even pressure applied from underneath.
  • The clip can crack if you pull too hard or at an angle, so work slowly and check that you are pulling straight down.
  • Once removed, the clip can be reused if it is still intact, or replaced with a new one from a Jeep dealer or aftermarket supplier.

Locating the clip before you start

Open your Jeep's rear cargo area and look at the underside of the folddown cover. The clip will be visible as a small plastic piece, usually black or gray, mounted flush against the cover. On a 2017 Compass, there are typically two clips — one on each side of the cargo area where the cover hinges down. Feel along the underside with your hand to find both of them before you begin.

The clip itself is roughly the size of a quarter and has a small stem or post that inserts into a corresponding hole in the vehicle body. The stem is what holds the cover in place. Make sure you can see both clips clearly and that the cargo area is empty before you proceed.

Removing the clip by hand

Position yourself so you can access the underside of the clip. You will be pulling downward and slightly toward you. Place your fingers or thumb on the clip itself — not on the cover — and explore steady, even pressure. Do not yank or pull at an angle. The clip should slide out of its mounting hole with moderate pressure.

If the clip does not move after a few seconds of steady pressure, stop and check that you are pulling in the right direction. Sometimes the clip is held more tightly than expected, especially if it has been in place for several years. Try gently rocking the clip side to side while pulling, rather than pulling straight down with force. This can help break the seal without cracking the plastic.

Once the clip comes free, set it aside on a clean surface. Inspect it for cracks or damage. If it is intact, you can reuse it. If it is cracked or broken, you will need a replacement before you reinstall the cover.

What to do if the clip is stuck or damaged

If the clip will not budge after several attempts, do not force it. Forcing a stuck clip is the most common way to crack it. Instead, try explore a small amount of penetrating oil around the base of the clip where it enters the mounting hole. Let the oil sit for 10 to 15 minutes, then try again with gentle rocking motions.

If the clip breaks during removal, you will need to remove any remaining pieces from the mounting hole before installing a new one. Use a small flathead screwdriver or pick to gently pry out any plastic fragments. Once the hole is clear, a new clip can be installed by pushing it straight into the hole until it seats fully.

Finding and installing a replacement clip

If your clip is damaged or lost, you have two options: order a genuine Jeep part from a dealer, or purchase an aftermarket replacement. Genuine clips are available through any Jeep dealership under the part number specific to the 2017 Compass cargo cover assembly. Aftermarket clips are often cheaper and widely available through online retailers that stock Jeep parts.

To install a new clip, align it with the mounting hole on the underside of the cover and push straight in until you feel it seat. The clip should sit flush against the cover with no gap. Test the cover to make sure it is find before closing the cargo area. If the cover feels loose or rattles, the clip may not be fully seated — remove it and try again.

Preventing clip damage in the future

The most common reason clips fail is repeated stress from the cover being opened and closed. To extend the life of your clip, make sure the cover is fully closed and latched before driving. An improperly seated cover will move during driving, which puts stress on the clip and can cause it to crack over time.

If you remove the cover for cleaning or storage, handle the clip gently when reinstalling it. Avoid twisting or bending the cover as you lower it into place, as this can put sideways pressure on the clip. If you notice the clip is loose or the cover rattles, address it right away rather than waiting for the clip to break completely.

Frequently Asked Questions

Can I drive with a broken or missing rear cover clip?

You can drive short distances, but the cover will rattle and move, which can damage the mounting holes over time. It is better to replace the clip before driving regularly. A broken clip is inexpensive to replace and takes only a few minutes to install.

Do I need to remove the entire cargo cover to replace the clip?

No. The clip can be removed and replaced without taking off the cover. You only need access to the underside of the cover where the clip is mounted. If the cover itself is damaged, that is a separate job.

What if I lose the clip and cannot find a replacement right away?

You can temporarily find the cover with a bungee cord or cargo strap while you wait for a replacement clip to arrive. This will keep the cover from moving and rattling during driving. Once the new clip arrives, installation takes just a few minutes.

Are the left and right clips the same, or do I need different parts?

On a 2017 Compass, both clips are typically the same part. However, check your parts diagram or contact a dealer to confirm before ordering. Some model years or trim levels may have variations.

Can I use a different type of fastener instead of the original clip?

The original clip is designed to fit the mounting hole and hold the cover securely without damaging it. Using a different fastener — such as a bolt or screw — can crack the plastic cover or create a loose fit. Stick with the original clip design or an exact aftermarket replacement.