What tappet clearances are and why they matter
Tappet clearance is the small gap between the valve stem and the rocker arm (or cam follower) in your engine's valve train. When your engine is cold and at rest, this gap must be precisely set — usually between 0.004 and 0.012 inches, depending on your vehicle's make and model. If the gap is too small, the valve won't close fully and you'll lose compression and power. If it's too large, the valve opens late and closes early, which also costs you power and can cause a tapping noise from the engine.
Most modern engines with hydraulic valve adjusters don't need manual tappet adjustment — the hydraulics do it automatically. But older vehicles, many motorcycles, and some truck engines still use solid valve lifters that require manual adjustment. If your engine has started making a rhythmic ticking sound from the top of the engine, or if you've noticed rough idle or loss of power, incorrect tappet clearance is often the culprit.
Key Takeaways
- Tappet clearance must be checked and adjusted when the engine is cold, with the piston at top dead center on the compression stroke for each cylinder.
- You will need your vehicle's service manual to find the correct clearance specification and the exact firing order for your engine.
- A feeler gauge is the standard tool — you slide it between the valve stem and rocker arm until it fits snugly with light resistance.
- Incorrect clearance causes power loss, rough running, and valve damage over time, so this is preventive maintenance that protects your engine.
- If your engine has hydraulic valve adjusters, you do not adjust tappets manually — the system self-adjusts and requires only oil changes.
Check your service manual first
Before you touch anything, get the correct specifications for your vehicle. Open your service manual and find the valve clearance table — it will list the clearance in inches or millimeters for intake and exhaust valves. Intake and exhaust are often different, so write both down. The manual will also show you the firing order and which cylinders to adjust in which sequence.
If you don't have a manual, you can order one from the manufacturer, read a PDF from a parts supplier, or borrow one from a library or local mechanic. The cost of a manual is far less than the cost of setting clearances wrong and damaging valves. Do not guess at the specification — even 0.002 inches off will cause problems.
Gather your tools and prepare the engine
You will need a feeler gauge set (a set of thin metal blades in graduated thicknesses), a socket wrench to fit your rocker arm adjusting nut, and a wrench to turn the engine over by the crankshaft bolt. Some engines have a bolt on the front of the crankshaft; others require you to remove the spark plugs and turn the engine by hand. Check your manual for the method on your vehicle.
Park on level ground, set the parking brake, and let the engine cool completely — at least two hours. Tappet clearance must be measured when the engine is cold because metal expands as it heats, and a clearance set hot will be too tight when cold. Remove the valve cover and any other components blocking access to the rocker arms. Keep track of where everything came from; take photos if you're unsure.
Position the engine and identify which valve to adjust
Turn the engine over slowly until the piston in cylinder number one reaches top dead center on the compression stroke. You can find this by removing the spark plug from cylinder one, placing your thumb over the hole, and turning the engine until you feel pressure pushing your thumb out — that's compression stroke. When the piston reaches the top, the intake and exhaust valves for that cylinder will both be closed, and the rocker arms will be resting on the base circle of the cam lobe (the lowest point).
At this position, you can adjust both valves in cylinder one. Then turn the engine one full rotation plus the number of degrees specified in your manual (usually 120 degrees for a four-cylinder, 90 degrees for a six-cylinder) and adjust the next cylinder in the firing order. Your manual will show the exact sequence. This ensures you never adjust a valve while its cam lobe is pushing on the rocker arm.
Measure and adjust each valve
Slide the correct feeler gauge between the valve stem and the rocker arm. The gauge should fit snugly with light resistance — you should feel a slight drag as you pull it out, but it should not be tight enough to bend. If the clearance is too small, the gauge won't fit. If it's too large, the gauge will slide through with no resistance.
If adjustment is needed, loosen the locknut on the rocker arm adjusting screw with one wrench while holding the screw steady with another. Turn the adjusting screw clockwise to decrease clearance (make the gap smaller) or counterclockwise to increase it. After each small turn, recheck with the feeler gauge. Once the clearance is correct, hold the adjusting screw steady and tighten the locknut firmly — do not overtighten, as this can bend the rocker arm.
Repeat this process for every valve in the firing order sequence. Write down each clearance as you go so you have a record. If you find that several valves are far out of specification, the engine may have worn valve seats or rocker arms, and you should have a mechanic inspect before continuing.
Reassemble and test
Once all valves are set, reinstall the valve cover gasket and bolts. Use a new gasket if the old one is cracked or flattened — a leaking valve cover will let oil escape and dirt enter. Reinstall any other components you removed, reconnect the spark plug wires or coils in their original order, and start the engine.
The engine should start smoothly without excessive ticking from the valve train. If you hear a loud tapping noise, stop when ready and recheck your work — you may have set a clearance too large. If the engine runs rough or idles poorly, verify that all spark plug connections are tight and in the correct order. Take the vehicle for a short test drive to confirm smooth acceleration and no hesitation.
When to adjust tappets and what goes wrong if you don't
Check your service manual for the recommended interval — some manufacturers suggest every 12,000 miles, others every 24,000 miles or longer. If your engine has begun to tick, or if you're rebuilding an engine, you must set tappets before running it. Worn valve seats, bent pushrods, or a damaged cam lobe will cause clearance to drift out of specification faster than normal, so if you find yourself adjusting frequently, have a mechanic inspect the valve train.
Ignoring tappet clearance leads to real damage. Too-tight clearance prevents valves from closing fully, which causes compression loss, overheating, and eventually a burned valve seat that requires cylinder head removal to repair. Too-loose clearance causes late opening and early closing, which reduces power and can allow a valve to strike the piston if clearance is extremely large. Both conditions accelerate wear on the cam lobe and rocker arms. Setting tappets correctly is cheap insurance against expensive engine work.
Frequently Asked Questions
Do I need to adjust tappets if my engine has hydraulic valve lifters?
No. Hydraulic lifters automatically maintain the correct clearance as the engine runs and the oil pressure changes. These engines require only regular oil changes. If your engine has hydraulic lifters and is making valve noise, the problem is usually low oil level, dirty oil, or a failing lifter — not clearance adjustment.
What happens if I set the clearance too tight?
Too-tight clearance prevents the valve from closing fully, which causes compression loss, rough running, and overheating. Over time, the valve seat will burn and the valve will leak. This requires removing the cylinder head to repair and is expensive.
Can I adjust tappets with the engine warm or running?
No. Clearance must be measured cold because metal expands as it heats. A clearance set warm will be too tight when the engine cools, and you risk valve damage. Always wait for the engine to cool completely before measuring.
How do I know which cylinder is number one?
Your service manual will show a diagram of the engine with cylinder numbers marked. Cylinder one is always the reference point for timing and valve adjustment. On most vehicles, it's the first cylinder in the firing order, but check your manual to be certain.
What if I can't get the feeler gauge to fit between the valve stem and rocker arm?
The clearance is too tight. Loosen the rocker arm adjusting screw by turning it counterclockwise, then recheck. If the clearance is still too tight after backing off the screw, the rocker arm or valve stem may be worn or bent, and you should have a mechanic inspect before continuing.