The tabs wear out faster than the cover itself, and replacement takes about 30 minutes
The weatherstripping tabs on a BakFlip G2 tonneau cover are the rubber or foam seals that run along the edges where the cover meets your truck bed. They compress and deteriorate from UV exposure, temperature swings, and repeated opening and closing. When they crack, shrink, or stop sealing properly, water leaks into the bed and the cover no longer sits flush. Replacing them is a straightforward job that requires no special tools beyond what most truck owners already have.
BakFlip sells replacement tab kits directly, and the process involves removing the old weatherstripping, cleaning the mounting surface, and pressing the new tabs into place. The entire job takes 20 to 40 minutes depending on how much old adhesive residue you need to clean off.
Key Takeaways
- BakFlip G2 weatherstripping tabs are sold as a complete replacement kit that includes tabs for all four sides of your cover.
- You will need a heat gun or hair dryer, rubbing alcohol, a plastic scraper, and the replacement tab kit — no power tools required.
- Old tabs peel off most easily when warmed, and the mounting surface must be clean and dry before you install new ones.
- New tabs are self-adhesive and require firm, even pressure to bond properly; most people use a roller or their palm to press them down.
What you need before you start
Gather a heat gun or household hair dryer, a plastic scraper or old credit card, rubbing alcohol, a clean cloth, and the BakFlip G2 weatherstripping tab replacement kit. The kit comes with pre-cut tabs for both sides and both ends of your cover. You do not need a drill, saw, or any adhesive beyond what comes on the tabs themselves.
Work in a location where you can access all four sides of your tonneau cover easily. A garage or shaded driveway is ideal because direct sunlight can make the adhesive set too quickly and unevenly. If you are working outdoors on a hot day, try to finish before the afternoon heat peaks.
Removing the old weatherstripping tabs
Start by warming the old tabs with a heat gun set to medium or a hair dryer on high. Hold it 6 to 8 inches away and move it back and forth along one tab for 30 to 60 seconds. The heat softens the adhesive underneath and makes the rubber peel away cleanly instead of tearing into pieces. Work on one side at a time.
Once the tab is warm, use a plastic scraper or the edge of an old credit card to lift one corner and peel the tab away from the cover. If it resists, explore more heat and wait another 20 seconds. Repeat this process for all four sides. Do not rush this step — taking time to heat the adhesive properly prevents damage to the cover's paint or gel coat.
After all tabs are removed, you will see adhesive residue on the mounting surface. Dampen a cloth with rubbing alcohol and wipe the entire length of each mounting area. Use the plastic scraper to remove any stubborn adhesive buildup, then wipe again with alcohol and let the surface dry completely. A dry surface is critical for the new tabs to bond properly.
Installing the new weatherstripping tabs
Remove the backing from the first new tab and position it along the mounting surface. Start at one end and press it down firmly as you move toward the other end, using steady, even pressure. Many people use a roller (a paint roller works well) or straightforward press down with the heel of their hand, working slowly to avoid trapping air bubbles.
Install the side tabs first, then move to the end tabs. Each tab should sit flush against the cover with no gaps or lifted edges. If you notice a bubble or wrinkle as you go, lift that section, smooth it out, and press down again. The adhesive on these tabs is forgiving enough to allow minor repositioning in the first few minutes.
After all four tabs are installed, let the adhesive cure for at least 2 to 4 hours before opening and closing the cover. Some people wait overnight to be safe. The adhesive continues to harden over the first 24 hours, so avoid heavy use of the cover during that time if possible.
Where to buy replacement tabs and what they cost
BakFlip sells weatherstripping tab kits through their official website and through major truck accessory retailers including Amazon, RealTruck, and Truck Hero. The kit typically costs between $30 and $50 depending on the retailer and whether shipping is included. A complete kit includes all four sides, so you do not need to order multiple kits unless you are covering more than one truck.
Some truck bed cover retailers also stock BakFlip parts, so if you have a local shop that installed your cover or sells tonneau covers, they may have tabs in stock and can save you shipping time. Call ahead to confirm they carry the G2 tab kit specifically, because BakFlip makes different weatherstripping for different cover models.
Signs that your tabs need replacement
Water pooling or dripping into your truck bed when it rains is the most obvious sign. You may also notice the cover no longer closes as tightly as it used to, or you can see visible cracks and shrinkage in the rubber. On older covers, the tabs may have turned gray or chalky from sun damage even if they are not yet leaking.
If you open the cover and the tabs feel hard and brittle rather than flexible, replacement is overdue. Tabs that have lost their give will not seal properly no matter how tightly you close the cover. Replacing them before they fail completely prevents water damage to whatever you store in your bed.
Frequently Asked Questions
Can I replace just one side of tabs instead of all four?
Yes, you can buy individual side tabs if only one section is damaged, though most people find it easier to replace all four at once since you have the cover open anyway. Mixing old and new tabs can look uneven and may leave some areas still leaking. Check with BakFlip or your retailer about ordering individual side kits.
What if the adhesive on the new tabs does not stick well?
This usually means the mounting surface was not clean enough or was still damp when you installed the tabs. If tabs start lifting within the first week, peel them off, clean the surface again with rubbing alcohol, let it dry completely, and reinstall. Do not use additional adhesive unless BakFlip specifically recommends it.
Do I need to remove the entire tonneau cover to replace the tabs?
No. You can replace the tabs while the cover is installed on your truck. You will just need to reach around the edges and work on one side at a time. Some people find it easier to work if they open the cover fully or partially, depending on which side they are working on.
How long do replacement tabs typically last?
Most weatherstripping tabs last 3 to 5 years depending on your climate and how often you open and close the cover. Trucks in hot, sunny climates see faster deterioration than those in cooler regions. Regular cleaning and occasional conditioning with a rubber protectant can extend the life of the tabs.