What the diverter valve does and why it fails
The diverter valve in your 2020 Chevy Trax sits on the turbocharger and controls where pressurized air goes when you lift off the throttle. When you're accelerating and then suddenly ease up, the valve vents excess boost pressure to prevent damage to the engine and transmission. If it sticks, cracks, or loses its seal, boost pressure leaks where it shouldn't, and you'll feel hesitation, hear a whistling sound, or see a check engine light.
The valve itself is a plastic and metal assembly that wears out from heat cycling and pressure changes. On the 2020 Trax with the 1.4-liter turbo engine, it's one of the more common wear items. Replacing it is a job you can do at home with basic tools if you're comfortable working around the engine bay, though the tight space makes it fiddly rather than difficult.
Key Takeaways
- The diverter valve sits directly on top of the turbocharger and controls boost pressure when you release the throttle.
- You'll need a socket set, screwdrivers, a hose clamp tool, and a new OEM or quality aftermarket valve; the part itself costs between $80 and $150.
- The job takes 45 minutes to an hour once you've removed the intake components that sit above it.
- Disconnect the negative battery terminal before you start, and let the engine cool completely so you don't burn yourself on the turbo housing.
- The hardest part is reaching the bolts and hose clamps in a confined space, not the mechanical work itself.
Tools and parts you'll need
Gather these before you start: a socket set (metric, 8mm through 15mm), a Phillips and flathead screwdriver, a hose clamp removal tool or needle-nose pliers, a new diverter valve (GM part number 55565139 for the OEM Chevy part, or equivalent aftermarket), and a container to catch any coolant that drips when you disconnect hoses.
You'll also want a clean rag, a flashlight or headlamp, and jack stands if you need to raise the vehicle for better access. The OEM Chevy valve runs $100 to $150 depending on your supplier; quality aftermarket valves from brands like Dorman or ACDelco cost $80 to $120. Do not buy the cheapest option on an auction site—diverter valves that fail prematurely often come from suppliers with no quality control.
Disconnect the battery and remove the intake components
Turn off the engine and let it cool for at least 30 minutes. The turbocharger housing gets hot enough to cause serious burns. Once it's cool, open the hood and disconnect the negative battery terminal using a 10mm socket. This prevents accidental electrical shorts while you're working.
The diverter valve sits under the intake manifold and air intake tube on the 2020 Trax. You'll need to remove the plastic air intake duct that runs from the air filter box to the throttle body. Loosen the hose clamp where it connects to the throttle body using your hose clamp tool or pliers, then twist and pull the duct free. Set it aside—you don't need to disconnect it from the air filter box.
Next, remove the intake manifold cover (the plastic piece on top of the engine). It's held by three bolts: two on the sides and one in the middle. Use a 10mm socket to remove all three, then lift the cover straight up and set it aside. You now have a clearer view of the diverter valve, which sits on the turbo housing below.
Locate and access the diverter valve bolts
The diverter valve is a cylindrical component about 3 inches long, mounted horizontally on top of the turbocharger. Two bolts hold it in place: one on the front and one on the rear. A vacuum hose connects to the top, and a vent hose connects to the bottom. The space is tight, and the rear bolt is the hardest to reach because it sits close to the firewall.
Use a flashlight to see both bolts clearly before you start. The front bolt is easier to access with a 13mm socket and a short extension. The rear bolt requires a 13mm socket as well, but you may need a flex-head ratchet or a universal joint to angle the socket properly. Take your time here—forcing a socket onto a bolt in a tight space can round it off.
Remove the old valve and disconnect the hoses
Once both bolts are loose, you can remove the front bolt completely. The rear bolt can stay partially threaded while you work on the hoses—this keeps the valve from dropping. Locate the vacuum hose on top of the valve and the vent hose on the bottom. The vacuum hose usually has a small clamp; use your hose clamp tool to loosen it, then twist the hose off. The vent hose may be held by a clamp as well, or it may straightforward push-fit onto a nipple.
Once the hoses are free, remove the rear bolt completely and carefully lower the valve out of the engine bay. Inspect the rubber seals on the valve—if they're cracked or hard, that confirms the valve failed. Check the hoses themselves for cracks or deterioration. If either hose is damaged, replace it now rather than discovering it later.
Install the new diverter valve
Before you install the new valve, compare it side-by-side with the old one to confirm they're identical. The bolt holes, hose connections, and overall shape should match exactly. If they don't, you have the wrong part—stop and verify the part number.
Position the new valve in the same orientation as the old one, with the vacuum hose connection on top and the vent hose connection on the bottom. Insert the rear bolt first and thread it by hand until it's snug—don't tighten it fully yet. Then insert the front bolt and thread it by hand as well. Once both bolts are hand-tight, use your socket and ratchet to tighten them firmly. They don't need to be cranked down hard; 15 to 20 foot-pounds is sufficient.
Reconnect the vacuum hose to the top of the valve and find the clamp. Reconnect the vent hose to the bottom and find its clamp if it has one. Make sure both hoses are seated fully and the clamps are tight enough that the hoses won't slip off under boost pressure.
Reassemble and test
Reinstall the intake manifold cover by aligning it over the three bolt holes and threading the bolts by hand first. Once all three are hand-tight, tighten them with your socket. Reconnect the air intake duct to the throttle body and tighten the hose clamp. Reconnect the negative battery terminal.
Start the engine and listen for any unusual sounds—a whistling or hissing that wasn't there before would indicate a hose isn't seated properly. Let the engine idle for a minute, then turn it off and check for any leaks around the new valve. If everything looks dry and sounds normal, take the vehicle for a short test drive. You should feel smoother throttle response and no hesitation when you accelerate and release the throttle.
If the check engine light was on before the replacement, it may take a few drive cycles to clear. If it stays on after 50 miles of normal driving, the issue may be elsewhere in the boost system, and you should have the fault codes read at a shop.
Frequently Asked Questions
Can I replace the diverter valve without removing the intake manifold cover?
Not easily. The cover sits directly above the valve and blocks access to both bolts. You could potentially work around it by removing only the front portion, but removing the whole cover takes five minutes and gives you much better visibility and access. It's worth doing.
What happens if I don't tighten the hose clamps enough?
The hoses will slip off under boost pressure, and you'll lose the diverter function. You'll hear a loud whistling sound and feel hesitation during acceleration. The engine won't be damaged, but you'll need to pull over and reseat the hoses or have it towed to a shop.
Do I need to replace the hoses when I replace the valve?
Only if they're cracked, hardened, or visibly deteriorated. If they look flexible and have no splits, they're fine to reuse. Hoses that are 4 or 5 years old on a 2020 model are usually still good, but inspect them carefully before you decide.
Will this fix a check engine light for a diverter valve code?
Yes, if the code is specifically for the diverter valve (P0045 or P0046 are common). If the code is for a boost pressure sensor or intake leak, the diverter valve replacement won't fix it. Have the fault code read before you assume the valve is the problem.
How long does the new valve last?
A quality OEM or aftermarket valve typically lasts 80,000 to 120,000 miles under normal driving. Some last longer; some fail sooner if the engine runs high boost pressure or if the cooling system isn't maintaining proper temperature. There's no scheduled replacement interval—you replace it when it fails.