The wireless charging tray comes out from underneath, not from the top

The BMW wireless charging tray (part number 849900) sits in a recessed pocket in your center console. To remove it, you do not pry it up from the surface. Instead, you access it from below the console, either by removing the entire console or by reaching underneath through the gear shift opening or storage compartments. The exact approach depends on your BMW model year and interior layout.

Most owners find it faster to remove the lower console panels first, which gives you clear access to the tray's mounting points. You will need a trim removal tool or a plastic pry tool to avoid scratching the interior, and about 20 to 30 minutes for the full job.

Key Takeaways

  • The charging tray is mounted from underneath the console, so you must access it from below rather than pulling it up from the top.
  • Removing the lower console panels or storage compartments gives you the clearest path to the tray's fasteners.
  • You will need a plastic trim removal tool and a socket set or screwdriver, depending on how your model secures the tray.
  • Disconnect the charging coil's electrical connector before fully removing the tray to avoid damaging the wiring.

Locate the fasteners underneath the console

Start by opening your center console storage compartment or the area below the gear shift. Look up into the space where the charging tray sits. You should see either bolts or clips holding the tray in place from underneath. On most BMW models, the tray is secured with two to four fasteners — typically M6 or M8 bolts, or plastic clips depending on the generation.

If you cannot see the fasteners clearly, remove the lower console trim panels. Use your plastic pry tool to gently release the clips holding these panels in place, working from one corner and moving around the perimeter. Take a photo with your phone before you start so you remember how the panels fit back together.

Disconnect the electrical connector

Before you remove the tray completely, locate the electrical connector that powers the charging coil. This connector is usually a small plastic plug with two or three wires, positioned on the underside of the tray or along the wiring harness nearby. Gently press the release tab on the connector and pull it straight out. Do not yank on the wires themselves.

If the connector is difficult to reach, you may need to remove one or two additional trim pieces or move nearby components slightly. Take your time here — damaging the connector or the wiring will require electrical repair work beyond the scope of tray removal.

Remove the fasteners and lift the tray out

Once the electrical connector is free, remove the bolts or unclip the fasteners holding the tray. If your tray uses bolts, use a socket wrench or screwdriver to remove them completely and set them aside in a small container so they do not roll away. If it uses clips, press or pull them according to how they are designed — some release by pressing inward, others by pulling outward.

Carefully lift the tray straight up and out of its pocket. The tray itself is plastic and relatively light, but move slowly to make sure no wiring is still attached or caught on the edges of the console opening. Set the tray on a clean surface where it will not be scratched or damaged.

Reinstall the tray or replace it

If you are reinstalling the same tray, reverse these steps: reconnect the electrical connector first, then position the tray back into its pocket and find it with the fasteners you removed. Tighten bolts firmly but do not over-tighten, as the plastic mounting points can crack. Reinstall the console trim panels, making sure each clip seats fully.

If you are replacing the tray with a new part 849900, the new tray should come with new fasteners or clips. Follow the same installation sequence: electrical connector first, then the tray, then the fasteners. Test the wireless charging function before you close up the console to confirm the new tray is working.

Common mistakes to avoid

Do not try to pry the tray up from the top surface of the console. This will crack the tray's edges and damage the surrounding trim. The tray is designed to come out from underneath only.

Do not disconnect the electrical connector while the tray is still bolted in place. You risk pulling the wires and damaging the connector or the harness. Always disconnect the power first, then remove the fasteners.

Do not force trim panels or fasteners. If something does not move easily, stop and look for a clip or bolt you may have missed. Forcing plastic trim will break it, and forcing bolts can strip the threads in the mounting points.

Tools and parts you will need

ItemPurpose
Plastic trim removal tool or soft pry toolRemove console panels without scratching plastic or paint
Socket set or screwdriver setRemove bolts holding the tray (size depends on your model)
Small containerHold fasteners so they do not get lost
Clean clothWipe the tray and console pocket before reinstalling
Replacement tray (if needed)Part number 849900 or equivalent for your model year

Frequently Asked Questions

Do I have to remove the entire center console to get the tray out?

No. Most models allow you to access the tray by removing just the lower console panels or storage compartments. Full console removal is rarely necessary and takes significantly longer. Try the panel removal approach first.

What if my tray is glued down instead of bolted?

Some older or aftermarket trays may be adhesive-mounted. If you find no bolts or clips, carefully work a plastic pry tool around the edges to break the adhesive seal. Work slowly and be prepared for the tray to crack if the adhesive is very strong. Replacement trays typically use bolts or clips, not adhesive.

Can I test the charging function without fully reinstalling the console panels?

Yes. Once the tray is back in place and the electrical connector is plugged in, you can place a compatible phone on the tray to test it before you reinstall the trim panels. This saves time if the new tray is defective and needs to be swapped out again.

What should I do if the electrical connector is damaged when I remove it?

Do not attempt to repair the connector yourself. Contact a BMW service center or an independent shop with electrical informed. A damaged connector can cause charging failure or electrical faults in the console. Replacement connectors and harnesses are available but require proper crimping and testing tools.

Is the wireless charging tray the same across all BMW models?

Part number 849900 is specific to certain BMW generations and model lines. Before you order a replacement, confirm the part number matches your vehicle's year, model, and interior configuration. Using the wrong part may not fit or may not connect to your vehicle's electrical system.