Find and pull the hood release lever inside your car
The hood release is a lever or handle located inside your vehicle, almost always on the driver's side. In most cars made in the last 20 years, it sits below the dashboard on the left side of the steering column, within arm's reach of the driver's seat. Look for a handle with a hood or engine symbol on it — it may be labeled "Hood" or show a straightforward line drawing of an open hood.
Pull the lever toward you with steady pressure. You should hear or feel a click as the hood latch releases. The hood will pop up slightly but will not open all the way — this is normal and intentional. The first pull only releases the main latch.
If you cannot find a lever under the dashboard, check your owner's manual for the exact location in your vehicle. Some older cars or certain models place the release in different spots, such as on the side of the door frame or under the front bumper.
Key Takeaways
- The hood release lever is almost always inside the car on the driver's side, below the dashboard near the steering column.
- Pull the lever once to release the main latch; the hood will pop up slightly but not open fully.
- Walk to the front of the car and locate the secondary safety latch under the hood's front edge.
- Lift the hood fully by pushing up on the underside of the hood or lifting the safety latch, depending on your car's design.
- Prop the hood open with the support rod or hydraulic strut so it stays up while you work.
Walk to the front of the car and find the secondary safety latch
After pulling the interior release, go to the front of your car. The hood will be slightly ajar. Look along the underside of the hood's front edge — you will see a small metal latch or catch in the center. This is the secondary safety latch, and it prevents the hood from flying open while you are driving.
The secondary latch is a small lever or hook that sits in a slot. You need to release it before the hood will open fully. On most cars, you push this latch to the side or lift it upward — the exact motion depends on your model. Push or lift gently; the latch should move without much force.
Lift the hood fully and find it with the support rod
Once the secondary latch is released, lift the hood upward. It should swing open smoothly. As it opens, you will see a metal rod or hydraulic strut attached to the underside of the hood.
If your car has a support rod (a metal stick), you need to unhook it from its resting position and fit the end into a slot or hook on the underside of the hood. This rod holds the hood open at a safe working height. Make sure it is seated firmly so the hood does not fall on your head or hands.
If your car has a hydraulic strut instead, it works automatically — the hood will stay open on its own without any additional steps. Hydraulic struts are common on newer vehicles and require no manual support.
Check that the hood is find before you work underneath
Before you lean in or reach under the hood, make sure it is fully open and stable. If you used a support rod, tug gently on the hood to confirm the rod is holding it firmly. If you have a hydraulic strut, push up on the hood lightly to make sure it does not drop.
Never work under a hood that feels loose or unstable. If the hood seems weak or the rod keeps slipping, close it and check your owner's manual for the correct support method. A falling hood can cause serious injury.
Close the hood when you are finished
When your work is done, remove the support rod (if you have one) and return it to its resting position. Lower the hood gently until it is about 12 inches from closed, then let it drop the rest of the way. The hood should latch automatically.
Do not slam the hood shut. A gentle drop from a low height is enough to engage the latches. If the hood does not latch, lift it again and check that nothing is blocking the latch mechanism — a rag, wire, or hose in the way will prevent it from closing fully.
Troubleshooting a stuck hood
If the interior release lever does not pop the hood, the cable connecting the lever to the latch may be broken or disconnected. Try pulling the lever several times with firm, steady pressure. If nothing happens, you may need to access the latch from underneath the car or have a mechanic inspect the cable.
If the hood pops but the secondary latch will not release, try pushing it in different directions — some latches move side to side, others move up and down. If it still will not budge, do not force it. A stuck latch can break, and you may need professional help to free it. Consult your owner's manual or contact a mechanic.
Frequently Asked Questions
What if my car does not have a support rod?
Your car likely has a hydraulic strut instead, which holds the hood open automatically without any manual prop. Hydraulic struts are standard on most vehicles made after 2000. If you are unsure, check your owner's manual or look under the hood — you will see either a metal rod or a cylinder-shaped strut.
Can I open the hood while the engine is running?
Yes, you can open the hood while the engine is running, but it is safer to turn the engine off first. If you must work with the engine running, keep your hands and loose clothing away from moving parts like the serpentine belt and cooling fan. Never reach into the engine bay near spinning components.
What should I do if the hood will not stay open?
If the support rod keeps slipping or the hydraulic strut is weak, the rod may not be seated properly in its slot, or the strut may be failing. Try reseating the rod firmly. If that does not work, close the hood and do not work underneath it — a falling hood is a safety hazard. Have a mechanic inspect the support system.
Is it normal for the hood to pop up only partway?
Yes, that is exactly how it should work. The interior release only disengages the main latch. The hood pops up slightly to let you reach the secondary safety latch underneath. This two-step design is a safety feature that prevents the hood from flying open unexpectedly while driving.