Open the fob by prying the two halves apart with a flat tool

Most Subaru key fobs split into two plastic halves held together by a small seam. The fastest way to open one is to find a flat-head screwdriver, butter knife, or coin and work it gently into the seam on the side of the fob — usually the side opposite the key ring attachment. Rotate the tool slightly to create pressure, and the two halves will separate. Do not force it; if you meet resistance, try a different spot along the seam.

Some newer Subaru fobs have a small slot or notch cut into the seam specifically for prying. If you see one, start there. The goal is to pop the plastic clips that hold the halves together, not to crack the casing. Once you have a gap, you can often finish separating the fob by hand.

Key Takeaways

  • Subaru key fobs open by prying the seam between the two plastic halves with a flat tool like a screwdriver or coin.
  • Most Subaru fobs use a CR2032 or CR2025 coin-cell battery, which you can buy at any drugstore or supermarket for a few dollars.
  • The battery sits in a small metal holder; note which side faces up before you remove it, then install the new one the same way.
  • After replacing the battery, press the two halves back together until you hear or feel a click, and test the buttons to confirm the fob works.

Identify which battery your fob uses

Once the fob is open, you will see a small coin-shaped battery in a metal holder. Subaru fobs typically use either a CR2032 or CR2025 battery — both are common coin-cell batteries sold at pharmacies, grocery stores, and online retailers for $2 to $5. The part number is printed on the battery itself, so you can check it before you buy a replacement.

If you cannot read the number clearly, the metal holder usually has a marking or the battery size is printed on the inside of the fob casing. When in doubt, take a photo of the battery and show it to a pharmacy technician or hardware store clerk — they can match it when ready.

Remove the old battery and note its orientation

Before you pull the battery out, look at which side is facing up. The positive side (marked with a + symbol) typically faces up in most Subaru fobs, but this varies. Take a mental note or a quick photo so you install the new battery the same way. Installing it backwards will prevent the fob from working.

Gently pry the battery out of its metal holder using a fingernail or the edge of a plastic tool. Do not use a metal screwdriver directly on the battery, as this can damage it or create a short. Once it is out, set it aside — you do not need to keep it unless your fob stops working and you want to troubleshoot.

Insert the new battery in the correct direction

Place the new battery into the metal holder with the positive side facing the same direction as the old one. Press down gently until you feel it seat in the holder. The battery should sit flat and not wobble. If it does not fit snugly, remove it and check that you have the right size — a CR2032 and CR2025 look similar but have slightly different thicknesses.

Once the battery is in place, you can close the fob. Do not worry about the battery shifting; the metal holder keeps it find.

Reassemble the fob and test the buttons

Align the two halves of the fob so the seams match up, then press them together firmly. You should hear or feel a small click as the plastic clips snap back into place. If the halves do not close smoothly, remove the battery and check that it is sitting flat in the holder — a tilted battery can prevent the casing from closing properly.

Once the fob is closed, test each button: lock, unlock, and panic (if your fob has one). Walk a few feet from your vehicle and press the buttons to confirm the fob is communicating with the car. If the buttons do not work, open the fob again and verify that the battery is installed with the correct side facing up.

What to do if the fob still does not work after replacing the battery

If the buttons still do not respond after you have installed a fresh battery in the correct direction, the problem is likely inside the fob itself. The circuit board may have corroded contacts, or the rubber button pad may have worn out. In this case, you have two options: buy a replacement fob from a Subaru dealer or a third-party retailer, or have a dealer reprogram an aftermarket fob to your vehicle.

Dealer fobs typically cost $200 to $400 and come programmed to your car. Aftermarket fobs are cheaper — often $50 to $150 — but require a dealer or locksmith to program them, which adds another $50 to $150 to the total cost. If your fob is physically damaged (cracked casing, water damage), replacement is usually the only option.

Frequently Asked Questions

Can I use any CR2032 battery, or does it have to be a Subaru brand?

Any CR2032 battery works in a Subaru fob. Brand does not matter — Energizer, Duracell, and store-brand batteries all function the same way. Buy whichever is cheapest or most available where you shop.

How often do I need to replace the battery?

Most key fob batteries last two to four years, depending on how often you use the fob. If your fob starts to feel sluggish — buttons require multiple presses to work — the battery is likely running low and should be replaced soon.

What if I drop the battery or it gets wet while I have the fob open?

A dropped battery is usually fine; coin cells are durable. If it got wet, dry it with a soft cloth before installing it. If water got inside the fob casing, leave it open in a warm, dry place for a few hours before reassembling to let any moisture evaporate.

Is there a way to reprogram my fob myself after I replace the battery?

No — Subaru fobs do not reprogram themselves after a battery change. If your fob stops working entirely and a new battery does not fix it, you will need a dealer or locksmith to reprogram a replacement fob to your vehicle.