The hood release is inside the cabin, below the steering wheel
To open a Jeep Wrangler hood, pull the hood release lever located on the left side of the dashboard, underneath the steering wheel. This lever is usually black or silver and sits near the floor. Pull it toward you with moderate force — it should click and the hood will pop up slightly. Then walk to the front of the vehicle, reach under the raised hood, and push the secondary latch (a metal bar or lever in the center) away from you to fully release the hood.
The exact location and style of the release lever varies slightly between model years. In older Wranglers (1997–2006), the lever is a straightforward pull handle. In newer models (2007 and later), it may be a lever that you pull or twist. If you cannot locate it under the steering wheel, check your owner's manual for your specific year — the manual will have a diagram showing the exact spot.
Key Takeaways
- The hood release lever is always inside the cabin on the left side below the steering wheel, not on the hood itself.
- Pull the interior lever first, then push the secondary latch at the front center of the hood to fully open it.
- The secondary latch prevents the hood from flying up while driving if the interior release accidentally opens.
- If the lever is stuck or broken, you may need to access the latch from underneath the vehicle or have a mechanic inspect the cable.
What the secondary latch does and why it matters
After you pull the interior release lever, the hood pops up a few inches but does not open all the way. This is intentional. The secondary latch — a metal catch at the front center of the hood — holds it in place as a safety feature. If only the interior lever controlled the hood, a broken cable or accidental bump could cause the hood to fly open while you are driving, blocking your view.
To release the secondary latch, reach under the partially open hood and locate the metal bar or lever in the center. Push it away from you (toward the windshield). The hood will then swing up freely. This two-step design is standard on nearly all vehicles and takes only a few seconds once you know where to look.
Troubleshooting a stuck or broken hood release
If the interior lever does not click or the hood does not pop up, the release cable may be broken or disconnected. Try pulling the lever several times with steady, firm pressure — sometimes the cable is just stiff from age or lack of use. If that does not work, spray a small amount of penetrating oil (such as WD-40) around the base of the lever where it enters the dashboard and wait a few minutes before trying again.
If the lever still does not work, you have two options. First, you can access the latch from underneath the vehicle by crawling under the front bumper area and manually pushing or pulling the secondary latch mechanism — this requires some space and visibility but works in a pinch. Second, and more reliably, take the Wrangler to a mechanic who can inspect the cable, replace it if needed, or repair the lever itself. A broken hood release cable typically costs between $150 and $300 to replace, depending on your model year and local labor rates.
Differences between Wrangler generations
Older Wranglers (1997–2006) have a straightforward pull lever under the steering wheel that is hard to miss — it is usually bright colored or clearly labeled. Newer Wranglers (2007–present) sometimes use a lever that twists or pulls, and the design can vary between the two-door and four-door models. In some 2018 and newer models, the release may be a push-button or electronic lever, though the secondary latch at the hood itself remains mechanical.
If you own a Wrangler and are unsure which generation you have, check the year on your registration or the door jamb label. Your owner's manual will have a diagram specific to your model year showing exactly where the release is located and how to operate it. Many owners keep a photo of the release location on their phone for quick reference.
Keeping the hood release in good working order
The hood release cable can corrode or seize over time, especially in areas with salt air or heavy rain. To keep it working smoothly, occasionally spray a small amount of penetrating oil around the base of the lever where it meets the dashboard. Do not spray directly into the mechanism — just a light mist around the edges is enough. Wipe away any excess with a clean cloth.
If you use your Wrangler off-road or in wet conditions regularly, inspect the cable and lever every six months. Look for signs of rust, fraying, or loose connections. A small amount of preventive maintenance now can save you from being stuck with a hood you cannot open later.
Frequently Asked Questions
Can I open the hood from outside if the interior release is broken?
Yes, but it requires getting under the vehicle. Crawl under the front bumper area and locate the secondary latch mechanism at the center of the hood. You can manually push or pull it to release the hood. This is awkward and dirty but works as a temporary fix until you can have the interior cable repaired.
Why does my hood only pop up partway?
That is the secondary latch doing its job. You must reach under the partially open hood and push the metal latch away from you to fully open it. If the hood will not open past the halfway point even after you push the latch, the latch may be bent or stuck and needs inspection.
Is the hood release the same on two-door and four-door Wranglers?
The location and basic operation are the same on both body styles, but the exact lever design may differ slightly. Check your owner's manual for your specific model to see the exact diagram for your Wrangler.
What should I do if the interior lever is stuck and will not budge?
explore penetrating oil around the base of the lever and wait 10 to 15 minutes. Then try pulling it again with steady pressure. If it still will not move, do not force it — you may break the cable. Have a mechanic inspect it instead.