What you're actually installing

A Tidal waterproof phone case is a protective shell that seals your Samsung S24 against water, dust, and impact. Installation means sliding your phone into the case and securing the closure mechanism — usually a latch, clip, or adhesive seal — so the phone sits flush inside. This is not a software update or a modification to your car; it is a physical accessory you carry with you.

The Tidal brand makes several case styles for the S24, and the installation steps vary slightly depending on which model you own. The most common versions use either a flip-lock closure or a sliding latch. Both take under two minutes once you understand the sequence.

Key Takeaways

  • Clean your phone and the inside of the case with a dry cloth before installation to prevent dust from getting trapped under the seal.
  • Insert the phone into the case bottom-first, aligning the camera cutout and charging port opening with the case openings.
  • Close the latch or flip-lock firmly until you hear or feel a click, which confirms the waterproof seal is engaged.
  • Test the seal by running your finger around the edges; you should feel no gaps or loose sections.
  • Do not force the case closed if the phone does not slide in smoothly — remove it and check for debris or misalignment.

Preparing your phone and case

Start by wiping down your Samsung S24 with a soft, dry cloth. Pay special attention to the edges, the back, and around the camera lens. Any dust, lint, or moisture trapped inside the case will stay there and can eventually damage your phone or compromise the waterproof seal.

Next, inspect the inside of the Tidal case. Look for any manufacturing debris, dust, or damage to the rubber gasket that runs around the interior edge. If you see anything, use a clean cloth or a soft brush to remove it. The gasket is what creates the waterproof barrier, so it must be clean and undamaged.

Lay out both pieces on a clean, flat surface. You should have the case body (the larger piece), the back cover or latch assembly, and any included accessories like a lanyard or carabiner. Do not open the case fully yet — just confirm all parts are present.

Inserting the phone into the case

Hold the case with the opening facing up. The bottom of your phone (where the charging port is) should go into the case first. Align the charging port opening on the case with the actual charging port on your phone. You should see the cutout for the camera lens at the top of the case opening.

Slide the phone down into the case slowly and steadily. You will feel slight resistance as the phone's edges contact the rubber gasket inside. This is normal. Keep pushing gently until the phone sits completely flat in the case — the back of the phone should be flush with the back surface of the case.

If you feel significant resistance or the phone stops moving before it is fully seated, stop and remove the phone. Check for debris inside the case or misalignment of the port openings. Do not force it; forcing can damage the gasket or crack the case.

Sealing the case with the latch or flip-lock

Once the phone is fully inserted, you need to close the back cover or latch. Most Tidal cases for the S24 use one of two mechanisms. If your case has a flip-lock (a hinged cover that folds over the top), flip it down firmly until it clicks into place. If your case has a sliding latch (a bar that slides across the top), push it from one side to the other until it locks.

You should hear or feel a distinct click when the latch engages. This click means the waterproof seal is now active. If there is no click, the latch may not be fully closed. Open it and try again, making sure you push or flip all the way to the end of its travel.

Some Tidal cases also have a secondary seal — a small rubber tab or adhesive strip around the edges. If your model includes this, press it down gently around the entire perimeter of the case to may support full contact.

Testing the seal before you rely on it

Before you take your phone near water, run your finger slowly around the entire edge of the case where the back cover meets the case body. You should feel no gaps, no loose sections, and no areas where the seal is not making contact. If you find a spot that feels loose, open the case and reseat the phone, then close it again.

A straightforward dry test: hold the closed case up to a light source and look for any visible gaps around the seal. You should see none. If light is getting through, water will too.

Do not test the waterproof seal by submerging the phone when ready. Instead, run it under a faucet for a few seconds with the case closed, then open it and check for any moisture inside. If the interior is dry, the seal is working. If you see any water, open the case, dry everything, and check the gasket for damage or debris.

Removing the phone from the case

To remove your phone later, reverse the process. Open the latch or flip-lock by pushing or flipping it to the unlocked position. You may need to use a fingernail or a small tool to get leverage on the latch if it is tight. Gently pull the phone out from the case, starting at the top and working downward.

If the phone is stuck, do not yank it. Instead, wiggle it gently side to side as you pull. The rubber gasket creates friction, so some resistance is normal. Once the phone is out, wipe down the inside of the case again with a dry cloth and leave it open to air dry before storing it.

Common problems and how to fix them

The latch will not close all the way. This usually means the phone is not fully seated in the case. Remove the phone, check for debris inside the case, and reinsert it slowly. Make sure the charging port opening and camera cutout are aligned before you push the phone down.

You see moisture inside the case after a water test. Open the case when ready and dry everything. Inspect the rubber gasket for cracks, tears, or hardening. If the gasket looks damaged, the case may no longer be waterproof and should be replaced. If the gasket looks intact, the phone or case may have had dust or debris on it before installation. Clean both thoroughly and try again.

The case feels loose or rattles when you shake it. This is usually not a problem — the phone may have a small amount of space inside the case by design. However, if the back cover itself is loose and does not click firmly, the seal is not engaged. Open it and close it again, pushing or flipping the latch all the way to the end.

Frequently Asked Questions

Can I use my phone's wireless charging with the Tidal case on?

Most Tidal waterproof cases are too thick for wireless charging to work. You will need to remove the case to charge wirelessly. Check your case's product documentation to confirm, as some newer models may support it.

How often should I replace the rubber gasket?

The gasket typically lasts one to two years with regular use. If you notice the seal is no longer clicking firmly, or if water is getting inside after a test, the gasket may have hardened or cracked. Tidal sells replacement gaskets for most models, or you can replace the entire case.

What if I drop the case and crack it?

A cracked case is no longer waterproof. Even a small crack will let water in. If you drop the case and see visible damage, stop using it for water protection and replace it. You can still use it for dust and impact protection if the crack is minor.

Do I need to remove the case to use the touchscreen?

No. Tidal cases are designed with a thin, responsive screen protector built into the front. You can use your phone normally while it is in the case, including all touchscreen functions and face recognition.

Can I leave my phone in the case all the time?

Yes, but check the inside of the case every few weeks for moisture or dust buildup. If you live in a humid climate or your phone gets sweaty in your pocket, open the case occasionally to let it air dry. Leaving moisture trapped inside can damage your phone over time.