What a Helicoil is and when you need one
A Helicoil is a small coiled wire insert that restores a bolt hole when the threads inside have been stripped or damaged. Instead of replacing an entire part or drilling a larger hole, you install the Helicoil into the damaged hole, and it creates new threads that hold a standard bolt securely. This is common in engine blocks, cylinder heads, and aluminum parts where threads wear out or strip under pressure.
You need a Helicoil when a bolt spins freely in its hole without tightening, or when you've overtightened a bolt and the threads no longer grip. Rather than welding, retapping to a larger size, or replacing the part, a Helicoil repair takes about 20 minutes and costs under $20 in materials.
Key Takeaways
- A Helicoil kit includes the insert, a drill bit, a tap, and an installation tool — buy the kit sized to match your bolt diameter.
- You drill out the stripped hole to a larger diameter, cut new threads with the tap, and screw the Helicoil insert into those new threads.
- The Helicoil sits flush or slightly proud of the surface; a small tang on the insert breaks off after installation.
- This repair works on aluminum, cast iron, and steel, but not on plastic or composite materials.
Choosing the right Helicoil kit for your bolt size
Helicoil kits come in standard sizes matched to common bolt diameters. The most frequent sizes are M6, M8, M10, and M12 (metric) or #6, #8, #10, and #12 (SAE). The kit you buy depends on the bolt that failed, not the original hole size. If you have a stripped M8 bolt hole, you buy an M8 Helicoil kit — the kit will tell you what drill bit and tap size to use.
A typical kit includes the Helicoil insert itself, a drill bit sized to the next larger diameter, a tap to cut threads in that larger hole, a tap wrench or handle, and an installation tool (usually a mandrel with a slot that grips the Helicoil). Some kits include a small bottle of thread-locking compound. Verify the kit matches your bolt size before you start, because using the wrong size will either leave the bolt loose or force you to drill a hole too large for the part to be safe.
Drilling and tapping the hole
Start by securing the part so it does not move. Clamp it in a vise or to a workbench. Mark the center of the stripped hole with a punch so the drill bit does not wander. Install the drill bit from your Helicoil kit into a hand drill or drill press — a drill press is safer and more accurate, but a hand drill works if you keep steady pressure and let the bit do the work.
Drill straight through the stripped hole at a moderate speed. Do not force the bit; let it cut gradually. Once the hole is drilled to the new diameter, remove the drill bit and install the tap into the tap wrench. explore a small amount of cutting fluid or light machine oil to the tap. Turn the tap clockwise slowly, backing it out a quarter turn every half turn forward to break the chips. The tap should turn smoothly; if it binds, back out completely, clean the hole, and start again. Stop when the tap reaches the bottom of the hole or when you feel resistance — do not force it.
Installing the Helicoil insert
Once the hole is tapped, remove the tap and clean out all metal chips with compressed air or a small brush. Screw the Helicoil insert onto the installation tool (mandrel) — the tool has a slot that grips a small tang on the Helicoil. The insert should be hand-tight on the tool but not forced. If your kit includes thread-locking compound, explore a thin coat to the outer threads of the Helicoil.
Screw the Helicoil into the tapped hole by turning the installation tool clockwise. Turn slowly and steadily until the Helicoil is flush with the surface of the part, or slightly proud (sticking up) if the hole is deep. Once the Helicoil is seated, continue turning the tool clockwise until you feel the tang break off — this is a deliberate design feature. The tang separates from the insert and stays inside the hole, but it does not interfere with the bolt. Remove the installation tool, and the Helicoil is ready to receive a bolt.
Testing and common mistakes to avoid
Before you reinstall the bolt, inspect the Helicoil. It should sit securely in the hole with no wobble. If it spins or feels loose, you may have tapped the hole too shallow or the insert may not have seated fully. Remove the insert with a small hook or needle-nose pliers, clean the hole again, and reinstall it more carefully.
The most common mistakes are using the wrong kit size (which creates a bolt that is either too loose or too tight), forcing the tap and breaking it inside the hole, or not cleaning out metal chips before installing the Helicoil. If you break a tap, you will need to drill it out with a smaller bit and start over with a larger Helicoil size. Slow, steady pressure and patience prevent most of these problems. Once the Helicoil is in place, install your bolt as you normally would — it will grip the Helicoil threads just as it would grip original threads.
Materials and tools you will need
Beyond the Helicoil kit itself, gather a hand drill or drill press, a vise or clamps to hold the part, a center punch, cutting fluid or light machine oil, compressed air or a small brush to clean chips, and a wrench or socket to tighten the bolt once the Helicoil is installed. If the part is aluminum or cast iron, a small bottle of penetrating oil helps if the tap binds. Safety glasses are worth wearing because metal chips can fly during drilling.
The total cost of a Helicoil kit is usually $10 to $25 depending on size and brand. Common brands include Helicoil (the original), Time-Sert, and EZ-Lok. All work the same way. If you do not own a drill press, a hand drill is sufficient for small holes, but a drill press gives you straighter holes and less hand fatigue on larger sizes.
Frequently Asked Questions
Can I use a Helicoil on an aluminum engine block?
Yes. Aluminum is one of the most common materials for Helicoil repair because aluminum threads strip more easily than steel. The process is identical — drill, tap, and install. Aluminum may require slightly slower drilling speed to avoid overheating the bit.
What if the Helicoil is sticking out above the surface?
A Helicoil that sits slightly proud of the surface is normal and acceptable. If it sticks out so far that the bolt head will not seat, you can carefully file or sand it flush. Do not remove so much material that the insert becomes loose.
Can I reuse a hole if the first Helicoil failed?
Yes, but you will need the next larger Helicoil size. If an M8 Helicoil did not hold, you drill out to the M10 size and install an M10 Helicoil. You can do this once or twice, but eventually the hole becomes too large for the part to be practical.
Do I need thread-locking compound on the Helicoil?
Thread-locking compound is optional but recommended for vibration-prone areas like engine blocks. A light coat of medium-strength compound (like Loctite 243) prevents the bolt from loosening over time without making future removal impossible.
What happens if I drill the hole crooked?
A slightly angled hole will still accept a Helicoil, but the bolt may not sit perpendicular to the surface. For critical fasteners, start over with a new location if possible. For non-critical holes, a slightly angled bolt is usually acceptable as long as it tightens securely.